HP cc2300 Guide

Manufacturing Part Number: A6898-96002
HP cc2300 Carrier Grade Server Quick
Start Guide
This guide contains basic instructions for setting up the system and accessing
the HP cc2300 Carrier Grade Server Product Guide from the HP Server cc2300
and cc3300 User Information Diagnostics and Utilities Resource CD.
Document Release Date: July 2000

Disclaimer
Information in this document is provided in connection with HP®products. No license, express or implied, by estoppel or
otherwise, to any intellectual property rights is granted by this document. Except as provided in HP's Terms and Conditions
of Sale for such products, HP assumes no liability whatsoever, and HP disclaims any express or implied warranty, relating to
sale and/or use of HP products including liability or warranties relating to fitness for a particular purpose, merchantability, or
infringement of any patent, copyright or other intellectual property right. HP products are not designed, intended or
authorized for use in any medical, life saving, or life sustaining applications or for any other application in which the failure of
the HP product could create a situation where personal injury or death may occur. HP may make changes to specifications
and product descriptions at any time, without notice.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
No part of this document may be copied, or reproduced in any form, or by any means without prior written consent of HP.
Intel is a registered trademark of Intel Corporation or its subsidiaries in the United States and other countries.
†Other names and brands may be claimed as the property of others.
Copyright © 2001 HP Corporation. All rights reserved.

HP cc2300 Carrier Grade Server Quick Start Guide iii
Contents
Specifications .......................................................................................................5
Regulatory Specifications and Disclaimers............................................................................6
Declaration of the Manufacturer or Importer .................................................................6
Removing the Server from the Box........................................................................................9
Selecting a Site .....................................................................................................................9
Checking the Power Connection .........................................................................................10
Connections and Controls ...................................................................................................13
Front Panel.................................................................................................................13
Back Panel .................................................................................................................15
Connecting the Monitor, Keyboard, and Mouse...................................................................16
Applying Power for the First Time........................................................................................16
The HP Server cc2300 and cc3300 User Information, Diagnostics and
Utilities Resource CD .....................................................................................................17
The cc2300 Carrier Grade Server Product Guide................................................................18
Warnings .............................................................................................................19
WARNING: English (US)....................................................................................................20
AVERTISSEMENTS : Français ..........................................................................................22
WARNUNG: Deutsch .........................................................................................................24
AVVERTENZA: Italiano......................................................................................................26
ADVERTENCIA: Español...................................................................................................28
Figures
1. Front View....................................................................................................................5
2. Front Panel Control Locations ....................................................................................13
3. DC Input Back Panel (AC Input Power Supply Shown Below) ....................................15
Tables
1. HP cc2300 CARRIER GRADE SERVER Physical Specifications................................5
2. Front Panel Features..................................................................................................14
3. Back Panel Features ..................................................................................................15

iv HP cc2300 Carrier Grade Server Quick Start Guide

HP cc2300 Carrier Grade Server Quick Start Guide 5
Specifications
Table 1. HPcc2300 CARRIER GRADE Server Physical Specifications
Specification Value
Height 1.7 inches (43 mm)
Width 17.12 inches (435 mm)
Depth 20 inches (508 mm)
Front clearance, minimum 2 inches (50.8 mm)
Side clearance, minimum 1 inches (25.4 mm)
Rear clearance, minimum 3.6 inches (92 mm)
Weight 22.5 lbs
Figure 1. Front View

6 HP cc2300 Carrier Grade Server Quick Start Guide
Regulatory Specifications and Disclaimers
Declaration of the Manufacturer or Importer

HP cc2300 Carrier Grade Server Quick Start Guide 7
Safety Compliance
USA: UL 1950 – 3rd Edition/CSA 22.2. No. 950-M93
Canada: UL Certified – 3rd Edition/CSA 22.2. No. 950-M93 for Canada (product bears
the single UL mark for U.S. and Canada)
Europe: Low Voltage Directive, 73/23/EECTUV/GS to EN60950 2nd Edition with
Amendments, A1 = A2 + A3 + A4
International: TUV/CB to IEC 60950 3rd Edition, EN60 950 2nd Edition + Amd 1-4,
EMKO-TSE (74-SEC) 207/94 plus international deviations
Australian / New Zealand: CB Report to IEC 60950, 3rd Edition plus Australian deviations
Electromagnetic Compatibility (EMC)
USA: FCC CFR 47 Part 2 and 15, Verified Class A Limit
Canada: IC ICES-003 Class A Limit
Europe: EMC Directive, 89/336/EEC
· EN55022, Class A Limit, Radiated & Conducted Emissions
· EN55024, ITE Specific Immunity Standard
· EN61000-4-2, ESD Immunity (Level 2 Contact Discharge, Level 3 Air
Discharge)
· EN61000-4-3, Radiated Immunity (Level 2)
· EN61000-4-4, Electrical Fast Transient (Level 2)
· EN61000-4-5, AC Surge
· EN61000-4-6, Conducted RF
· EN61000-4-8, Power Frequency Magnetic Fields
· EN61000-4-11, Voltage Dips and Interrupts
· EN61000-3-2, Limit for Harmonic Current Emissions
· EN61000-3-3, Voltage Flicker
Japan: VCCI Class A ITE (CISPR 22, Class A Limit) IEC 1000-3-2 Limit for Harmonic
Current Emissions
Australia/New Zealand: AS/NZS 3548, Class A
Taiwan: BSMI Approval, Class A
Korea: RRL Approval, Class A
Russia: GOST Approved
International: CISPR 22, Class A Limit
FCC Electromagnetic Compatibility Notice (USA)
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operating in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference. In this
case, the user is required to correct the interference at their own expense. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the

8 HP cc2300 Carrier Grade Server Quick Start Guide
equipment off and on; the user is encouraged to try to correct the interference by one or more of the
following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and the receiver.
· Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
· Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the grantee of this device could void the
user’s authority to operate the equipment. The customer is responsible for ensuring compliance of
the modified product.
Electromagnetic Compatibility Notices (International)
Europe (CE Declaration of Conformity)
This product has been tested in accordance too, and complies with the Low Voltage Directive
(73/23/EEC) and EMC Directive (89/336/EEC). The product has been marked with the CE Mark
to illustrate its compliance.
Japan EMC Compatibility
English translation of the notice above:
This is a Class A product based on the standard of the Voluntary Control Council for Interference
by Information Technology Equipment (VCCI). If this equipment is used in a domestic
environment, radio disturbance may arise. When such trouble occurs, the user may be required to
take corrective actions.
ICES-003 (Canada)
Cet appareil numérique respecte les limites bruits radioélectriques applicables aux appareils
numériques de Classe A prescrites dans la norme sur le matériel brouilleur: “Appareils
Numériques”, NMB-003 édictée par le Ministre Canadian des Communications.
English translation of the notice above:
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital
apparatus set out in the interference-causing equipment standard entitled “Digital Apparatus,”
ICES-003 of the Canadian Department of Communications.

HP cc2300 Carrier Grade Server Quick Start Guide 9
BSMI (Taiwan)
The BSMI Certification number and the following warning is located on the product safety label
which is located visibly on the external chassis.
Removing the Server from the Box
Carefully unpack the server. Save all packing materials in case the server needs to be shipped at a
later time.
Selecting a Site
Select a site that meets these criteria:
· Clean and relatively free of excess dust.
· Well-ventilated and away from sources of heat, with the ventilating openings on the server kept
free of obstructions.
· Away from sources of vibration or physical shock.
· Isolated from strong electromagnetic fields and noise caused by electrical devices such as
elevators, copy machines, air conditioners, large fans, large electric motors, radio and TV
transmitters, and high-frequency security devices.
For AC-powered servers:
· Place the server near a properly earthed, grounded, three-pronged power outlet.
¾ In the United States and Canada: a NEMA-compliant, 110-125 V outlet rated for 20 amps.
¾ In other geographic areas: a properly earthed, grounded outlet in accordance with the local
electrical authorities and electrical code of the region.
For DC-powered servers:
· Place the server near a -48 to -60 V DC supply.
· Verify that proper DC grounding is provided.
· Verify that proper insulation protects the DC connection terminals and wires.
CAUTION, ESD precautions
Electrostatic discharge (ESD) can damage disk drives, add-in boards, and
other parts. This server can withstand normal levels of environmental ESD.
However, we recommend doing all procedures in this guide only at an
ESD-protected workstation. If one is not available, you can provide some

10 HP cc2300 Carrier Grade Server Quick Start Guide
ESD protection by wearing an anti-static wrist strap attached to chassis
ground of the server when handling components (e.g. any unpainted metal
surface).
CAUTION, Use grounded outlet
Make sure that the power service connection is through a properly grounded
outlet.
Checking the Power Connection
WARNING
The Power button on the Front Control Panel of the server does not
completely remove AC power. To completely remove AC power from
the server, you must unplug/disconnect the power connection from the
system. Unplugging/disconnecting the power connection removes the
+12 Volt standby power that is present when the server is powered
down.
WARNING
Do not modify or use a supplied AC power cord if it is not the exact type
required in the region where the server will be installed and used.
Replace the cord with the correct type. Refer to the cord requirements
described below.
Do not connect power to the server (AC or DC) if you will be adding
internal parts (boards, DIMMs, removable media drives). For these
installation procedures, see the cc2300 Carrier Grade Server Product
Guide.
WARNING
The DC power source may produce hazardous voltage levels
exceeding -60 VDC and high energy levels above 240VA that may cause
electric shock or burns. All DC input connections should be made only
by a qualified service person only to prevent injury. All wiring
terminals connected to the DC input terminal block must be fully
insulated with no exposed bare metal.
If an AC power supply is installed:

HP cc2300 Carrier Grade Server Quick Start Guide 11
Mains AC power disconnect: The AC power cord(s) is considered the
mains disconnect for the server and must be readily accessible when
installed. If the individual server power cord(s) will not be readily
accessible for disconnection then you are responsible for installing an
AC power disconnect for the entire rack unit. This mains disconnect
must be readily accessible, and it must be labeled as controlling power to
the entire rack, not just to the server(s). To remove all power, the
AC cord must be removed.
Grounding the rack installation: To avoid the potential for an electrical
shock hazard, you must include a third wire safety ground conductor
with the rack installation. If the server power cord is plugged into an
AC outlet that is part of the rack, then you must provide proper
grounding for the rack itself. If the server power cord is plugged into a
wall AC outlet, the safety ground conductor in the power cord provides
proper grounding only for the server. You must provide additional,
proper grounding for the rack and other devices installed in it.
Overcurrent protection: The server is designed for an AC line voltage
source with up to 20 amperes of overcurrent protection per cord feed. If
the power system for the equipment rack is installed on a branch circuit
with more than 20 amperes of protection, you must provide
supplemental protection for the server. The overall current rating of the
server is less than 4 amperes.
If a DC power supply is installed:
The DC source must be electrically isolated by double or reinforced
insulation from any hazardous AC or DC source. The DC source must
be capable of providing up to 300 mW of continuous power. Connection
with a DC source should only be performed by trained service
personnel.
Mains DC power disconnect: You are responsible for installing a
DC power disconnect for the entire rack unit. This mains disconnect
must be readily accessible, and it must be labeled as controlling power to
the entire unit, not just to the servers(s).
Grounding the rack installation: To avoid the potential for an electrical
shock hazard, you must include a third wire safety ground conductor
with the rack installation. The safety grounding conductor must be a
minimum 14AWG connected to the earth ground stud on the rear of the
server. The safety ground conductor should be connected to the chassis
stud with a two hole crimp terminal with a maximum width of 0.25 inch.
The nuts on the chassis studs should be installed with a 10 in/lbs torque.
The safety ground conductor provides proper grounding only for the
server. You must provide additional, proper grounding for the rack and
other devices installed in it.

12 HP cc2300 Carrier Grade Server Quick Start Guide
Overcurrent protection: Overcurrent protection circuit breakers must
be provided as part of each host equipment rack and must be installed
between the DC source and the server. The server is designed for a
DC line voltage power source with up to 10 amperes of overcurrent
protection per feed pair. If the DC power system for the equipment rack
is installed with more than 10 amperes of protection, you must provide
supplemental protection for the server. The overall current rating of the
server is less than 7 amperes.
WARNING
Do not attempt to modify or use an AC power cord that is not the exact
type required. You must use a power cord that meets the following
criteria:
· Rating: For U.S./Canada cords must be UL Listed/CSA Certified
type SJT, 18-3 AWG. For outside U.S./Canada cords must be
flexible harmonized (<HAR>) or VDE certified cord with
3 x 0.75mm conductors rated 250 VAC.
· Connector, wall outlet end: Cords must be terminated in
grounding-type male plug designed for use in your region. The
connector must have certification marks showing certification by
an agency acceptable in your region and for U.S. must be rated
125% of overall current rating of the server.
· Connector, server end: The connectors that plug into the
AC receptacle on the server must be an IEC 320, sheet C19, type
female connector.
· Cord length and flexibility: Cords must be less than 4.5 meters
(14.76 feet) long.
NOTES
Surge Suppressor Recommendations: In geographic regions that are
susceptible to electrical storms, we highly recommend that you plug the
server into a surge suppressor.
EMI INFORMATION:
FOR INFORMATION ABOUT COMPLYING WITH ELECTROMAGNETIC
INTERFERENCE REGULATIONS, SEE “ELECTROMAGNETIC
COMPATIBILITY” IN THE CC2300 CARRIER GRADE SERVER PRODUCT
GUIDE.
CAUTION
Temperature: The temperature in which the server operates when installed
in an equipment rack, must not go below 5 °C (41 °F) or rise above 40 °C
(104 °F). Extreme fluctuations in temperature can cause a variety of
problems in your server.

HP cc2300 Carrier Grade Server Quick Start Guide 13
Ventilation: The equipment rack must provide sufficient airflow to the front
of the server to maintain proper cooling. The rack must also include
ventilation sufficient to exhaust a maximum of 1023 BTU's per hour for the
server. The rack selected and the ventilation provided must be suitable to the
environment in which the server will be used.
Connections and Controls
Front Panel
Figure 2 shows the front view of the system including the front panel. The front panel contains
system control switches, alarm indicators relays, connectors, and status indicators. Front panel
features are summarized in Table 2.
A NMI Switch G Alarm: PWR (green)
B System Power Switch H Status: NIC (green)
C System Reset I Status: DSK (HDD Activity, green)
D Alarm: CRT (Critical) J Status: Main Power (green)
E Alarm: MJR (Major) K Status: User ID (white)
F Alarm: MNR (Minor)
Figure 2. Front Panel Control Locations

14 HP cc2300 Carrier Grade Server Quick Start Guide
Table 2. Front Panel Features
Item Feature Description
Front Panel Switches
A NMI switch A momentary switch used to instruct the processor to copy system memory to
the hard drive. Pressing the recessed button with a paper clip or pin puts the
server in a halt state for diagnostic purposes and allows you to issue a
non-maskable interrupt. After issuing the interrupt, a memory dump can be
performed to determine the cause of the problem.
B Power switch Toggles the system power.
C Reset switch Reboots and initializes the system.
Front Panel Alarm LEDs and Relays
D Critical (amber) When continuously lit, indicates the presence of a Critical System Fault. A
critical system fault is an error or event that is detected by the system with a
fatal impact to the system. In this case, the system cannot continue to operate.
An example could be the loss of a large section of memory. The front panel
critical alarm relay will be engaged.
E Major (amber) When continuously lit, indicates the presence of a Minor System Fault. A major
system fault is an error or event that is detected by the system that has
discernable impact to system operation. In this case, the system can continue
to operate but in a “degraded” fashion (reduced performance or loss of
non-fatal feature reduction). An example could be the loss of one of two
mirrored disks. The front panel major alarm relay will be engaged.
F Minor (amber) When continuously lit, indicates the presence of a Major System Fault. A minor
system fault is an error or event that is detected by the system but has little
impact to actual system operation. An example would be a correctable ECC
error. The front panel minor alarm relay will be engaged.
G Power (amber) When continuously lit indicates the presence of a Power System Fault.
Additionally, the front panel power alarm relay will engage.
Front Panel Status LEDs
H NIC activity
LED (green)
Indicates NIC activity.
I HDD activity
LED (green)
Indicates any system SCSI hard drive activity.
J Main power
LED (green)
When continuously lit, indicates the presence of DC power in the server. The
LED goes out when the power is turned off or the power source is disrupted.
When it is blinking green, it indicates that the system is in ACPI sleep mode.
K User ID
LED (white)
When continuously lit, indicates that the user ID function has been activated.
Front Panel Connectors (Concealed by the Bezel)
RJ45 Serial
Connector
Serial Connector (also available on the back panel through a second
RJ45 connector).
2 x USB
Connectors
USB Port 2 and USB Port 3.

HP cc2300 Carrier Grade Server Quick Start Guide 15
Back Panel
Figure 3 shows the back panel view of the system.
Figure 3. DC Input Back Panel (AC Input Power Supply Shown Below)
You will find the back panel’s feature summary in Table 3.
Table 3. Back Panel Features
Item Description
A USB port 1
B One low profile, half-length 64-bit, 66 MHz PCI add-in board slot (3.3V riser board)
C Video connector
D External wide SCSI Ultra160 68-pin connector
E Dual NIC 10/100 E/N RJ45 connectors NIC 1 (lower) and NIC 2 (upper)
F DB-15 male connector for front panel alarm relay contacts
G PS/2†-compatible keyboard port, 6-pin connector
H Serial port, 8-pin RJ45 connector
I USB port 0
J One full height, full length 64-bit, 33 MHz PCI add-in board slot (5 V riser board), or,
One full height, full length 64-bit, 66 MHz PCI add-in board slot (3.3 V riser board)
K Two grounding lugs for attachment of grounding wire to chassis. For use only when configured
for DC input power supply
L 250 W power supply (DC input version shown above, AC Input version shown below)

16 HP cc2300 Carrier Grade Server Quick Start Guide
Connecting the Monitor, Keyboard, and Mouse
CAUTION:
UNPLUG THE SERVER. Before connecting external devices, make sure
the server is not plugged in, or equipment could be damaged.
Before turning on the server, you must connect these devices to the back of the cc2300 server.
1. Connect a video monitor to the video port (C in Figure 3 ).
2. Connect a keyboard and a mouse to the PS/2 y-cable shipped with the server. (Figure 3).
Applying Power for the First Time
WARNING
The DC power source may produce hazardous voltage levels exceeding
–72 VDC and high energy levels above 240VA that may cause electric
shock or burns. All DC input connections should be made only by a
qualified service person only to prevent injury. All wiring terminals
connected to the DC input terminal block must be fully insulated with no
exposed bare metal.
The first time you turn the server on you need to enter the BIOS Setup Utility and set the correct
date and time values. After setting these values the server executes its Power-On Self-Test (POST)
sequence and passes control to the Boot Manager.
For information on the Boot Manager, refer to the cc2300 Carrier Grade Server Product Guide.
Follow these steps to power up the cc2300 server for the first time:
1. Make sure all external devices, such as a monitor, keyboard, and mouse, have been connected.
2. Plug in the AC power cord or connect the DC power wiring to the back of the chassis (L in
Figure 3).
3. Plug the male ends of the server AC power cords into wall outlets (grounded, three-pronged
AC power outlets) or rack power distribution units.
4. Turn on the video monitor.
5. Press the Power button on the front panel (B in Figure 2). Pressing this button causes the server
fans to start up and POST to begin.
6. When POST displays the message: “Hit <F2> if you want to run SETUP,” enter <F2> and the
system will enter the BIOS Setup Utility. (If you see a prompt asking for a system password,
pressing the <ENTER> key will get you directly to the BIOS Setup Utility.)
NOTE
For information on how to use the BIOS Setup Utility, see the cc2300
Carrier Grade Server Product Guide.

HP cc2300 Carrier Grade Server Quick Start Guide 17
7. From the Main menu of the BIOS Setup Utility, use the arrow keys to move the cursor down to
the system date and time selections. Position the cursor over the date and time values and enter
appropriate values.
8. Use the <TAB> key to access the Exit menu and select the item to save changes and exit the
BIOS Setup Utility. After you exit the utility the boot procedure resumes. You can monitor the
remainder of the boot progress on the video display.
The HP Server cc2300 and cc3300 User Information,
Diagnostics and Utilities Resource CD
The cc2300/cc3300 ResourceCD has the following contents:
· Utilities:
¾ CSSU
¾ SSU
¾ ISC 3.5
¾ FRU/SDR Load Utility
¾ Service Partition Admin Utility
· cc2300 Carrier Grade Server Product Guide
· Adobe Acrobat Reader
The cc3300/cc2300 resource CD comes with a menu driven program that can be used for the
following:
1. Install ISC Service Partition. The ISC service partition provides the ability to remotely
access the cc2300 server via modem or LAN for the purpose of executing
configuration/setup utilities and diagnostics.
2. Run cc2300 Intel Server Control (ISC) based utilities. Refer to the Intel®Server Control
User’s Guide For the HP cc2300 & cc3300 Carrier Grade Servers for detailed ISC
information.
3. To invoke the cc2300/cc3300 Resource CD menu: Insert the Resource CD into the
CDROM drive.
4. Restart the server.
5. When the “F2 to enter setup” message appears, quickly press F2.
6. In Setup, use the arrow keys to select the Boot menu.
7. Use the arrow keys to select Boot Device Priority then press Enter.
8. Select ATAPI CDROM and use the + key to move the selection to the top of the list.
9. Press F10.
10. Select Yes to confirm saving of the current settings and press Enter. The server restarts and
boots from the Resource CD.
11. When the menu appears, use the arrow keys to select the Utilities menu.

18 HP cc2300 Carrier Grade Server Quick Start Guide
The cc2300 Carrier Grade Server Product Guide
The cc2300 Carrier Grade Server Product Guide comes as a single .PDF file shipped on the
cc2300/cc3300 Resource CD. Select the documentation directory to access the Product Guide.
NOTE
The product guide can only be read and printed from an IA-32 operating
system.

HP cc2300 Carrier Grade Server Quick Start Guide 19
Warnings
WARNING: English (US)
AVERTISSEMENTS : Français
WARNUNG: Deutsch
AVVERTENZA: Italiano
ADVERTENCIA: Español

20 HP cc2300 Carrier Grade Server Quick Start Guide
WARNING: English (US)
The power supply in this product contains no user-serviceable parts. There may be more
than one supply in this product. Refer servicing only to qualified personnel.
Do not attempt to modify or use the supplied AC power cord if it is not the exact type
required. A product might be equipped with more than one AC power cord.
The Power button on the system does not turn off all system power. To remove all power
from the system, you must unplug/disconnect the power cord from the system.
To avoid injury from electrical and mechanical hazards, chassis covers should only be
removed by qualified service personnel.
SAFETY STEPS: Whenever you remove the chassis covers to access the inside of the
system, follow these steps:
1. Turn off all peripheral devices connected to the system.
2. Turn off the system by pressing the Power button.
3. Unplug/disconnect the power cord from the system.
4. Label and disconnect all telecommunication cables and all other cables connected to I/O
connectors or ports on the back of the system.
5. Provide some electrostatic discharge (ESD) protection by wearing an anti-static wrist
strap attached to chassis ground of the system—any unpainted metal surface—when
handling components.
6. Do not operate the system with the chassis covers removed.
After you have completed the five SAFETY steps above, you can remove the system covers.
To do this:
1. Remove and save all screws from the covers.
2. Remove the covers.
For proper cooling and airflow, always reinstall the chassis covers before turning on the
system. Operating the system without the covers in place can damage system parts. To
install the covers:
1. Check first to make sure you have not left loose tools or parts inside the system.
2. Check that cables, add-in boards, and other components are properly installed.
3. Attach the covers to the chassis with the screws removed earlier, and tighten them
firmly.
4. Connect all external cables and the power cord to the system.
continued