HP cc2300 Owner's manual

Manufacturing Part Number: A6900-96001
E0502
Mfg. P/N: A6900-96001
*A6898-96001*
Safety and Regulatory Information
HP cc3300 Carrier Grade Server
Sicherheitshinweise und -normen
HP cc3300 Carrier Grade Server
Sécurité et réglementations
Serveur télécom HP cc3300
Información de Seguridad y Normativa
Servidor de Nivel de Operador HP cc3300
Informazioni sulla sicurezza e sulle norme vigenti
Server Carrier Grade HP cc3300
Informacje o zasadach bezpieczeństwa i zgodności z przepisami
HP cc3300 Carrier Grade Server
安全および規制に関する規約
HP cc3300 Carrier Grade Server
시스템 안전 및 규정 정보
HP cc3300 Carrier Grade 서버
安全和规格信息
HP cc3300 电信级服务器
安全及法規資訊
HP cc3300 電信級伺服器

Safety and Regulatory Information
HP cc3300 Carrier Grade Server
Regulatory Model: RSVLA-0108 and RSVLA-0108-DC
Manufacturing Part Number: A6900-96001
First Edition
© Copyright 2002

2 English
Notice
Hewlett-Packard makes no warranty of any kind with regard to this material, including but not limited to,
the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be
liable for errors contained herein or for incidental or consequential damages in connection with the furnishing,
performance, or use of this material.
Hewlett-Packard assumes no responsibility for the use or reliability of its software on equipment that is not
furnished by Hewlett-Packard.
All rights are reserved. No part of this document may be photographed, reproduced, or translated to another
language without prior written consent of Hewlett-Packard Company.
The information contained in this document is subject to change without notice.
Restricted Rights Legend. Use, duplication or disclosure by the U.S. Government is subject to restrictions as set
forth in subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS
252.227-7013 for DOD agencies, and subparagraphs (c) (1) and (c) (2) of the Commercial Computer Software
Restricted Rights clause at FAR 52.227-19 for other agencies.
HEWLETT-PACKARD COMPANY 3000 Hanover Street Palo Alto, California 94304 U.S.A.
Copyright Notices. ©copyright 1983-2002 Hewlett-Packard Company, all rights reserved.
Reproduction, adaptation, or translation of this document without prior written permission is prohibited, except as
allowed under the copyright laws.
Trademark Notices UNIX is a registered trademark in the United States and other countries, licensed exclusively
through X/Open Company Limited.

HP Carrier Grade Server Safety and Regulatory Information
English 3
HP Carrier Grade Server Safety and Regulatory
Information
Notational Conventions
WARNING Warnings highlight procedures or information necessary to avoid injury to personnel. The
warning shall tell the reader exactly what will result from what actions and how to avoid
them.
CAUTION A caution highlights procedures or information necessary to avoid damage to equipment, damage to
software, loss of data, or invalid test results.
NOTE A note highlights supplemental information.
Overview
Hewlett-Packard utilizes numerous marketing model numbers and nomenclature to identify Enterprise Server
products. Within a product family, the marketing modelnumber typically identifies differences in the processor and
I/O options. A product family is defined as a group of products wherein the form, fit, function, and power
subsystem are essentially the same. Our practice is to assign a "regulatory number" to a product family to support
monitoring and control of changes that potentially impact safety and EMC. The assigned regulatory product
numbers for this product are RSVLA-0108 and RSVLA-0108-DC. The regulatory product numbers RSVLA-0108
and RSVLA-0108-DC are equivalent to the marketing designations referenced throughout this document.
Regulatory Compliance statements are required by some countries or areas for international importation of the HP
Carrier Grade Server. The following information is provided:
Product Information
Regulatory Information
Electrical Safety
Electrostatic Discharge (ESD) Precautions
International Symbols (IEC 417)
Associated Documents
Installation Conditions
Fuse Warnings

HP Carrier Grade Server Safety and Regulatory Information
4 English
Lithium Battery Warning
Cabinet Safety Precautions
Declaration of Conformity
FCC Statement (USA Only)
Canada RFI Statement
European Union RFI Statement
Acoustics (Germany)
Australian C-Tick Label
Laser Safety
Product Information
For detailed information on the HP Carrier Grade Server product, please go to the http://docs.hp.com Web site (in
the Systems Hardware selection).
Regulatory Information
For your protection, this product has been tested for conformance to various national and international regulations
and standards. The scope of this regulatory testing includes electrical and mechanical safety, electromagnetic
emissions, immunity, acoustics and hazardous materials.
When required, approvals are obtained from third party test agencies. Approval marks appear on the product label.
In addition, various regulatory bodies require some information under the headings listed in this section.
Electrical Safety
Locate the DC outlet near the computer! The DC power cords are this product's main DC disconnect devices and
must be easily accessible at all times.
Electrostatic Discharge (ESD) Precautions
When handling any electronic component or assembly (such as, a PCI card or Memory SIMM), you must observe
the following antistatic precautions to prevent damage. An ESD kit (HP Part Number A5201-68004) is available
(or supplied with Memory additions). This kit contains one wrist strap, one conductive sheet, and one anti-static
foam pad.
• Always wear a grounded wrist strap when working around the system, and when handling printed circuit
boards.
• Treat all assemblies, components and interface connections as static-sensitive.
• Avoid working in carpeted areas, and keep body movement to a minimum while removing or installing boards,
to minimize buildup of static charge.

HP Carrier Grade Server Safety and Regulatory Information
English 5
International Symbols (IEC 417)
Figure 1 Protective Earth (ground)
Figure 2 Direct Current
Figure 3 Alternating Current
Figure 4 On (Supply)
Figure 5 Off (Supply)

HP Carrier Grade Server Safety and Regulatory Information
6 English
Associated Documents
The following documents provide more details on the topics presented in this manual:
• Standard for the Protection of Electronic Computer Data Processing Equipment, (NFPA75) National
Fire Protection Association
• EIA Standard RS-232-C, Electronic Industries Association
• Electrostatic Discharge Failures of Semiconductor Devices, Unger, B.A. 1981, Bell Laboratories
• HP Carrier Grade Server: Installation Guide
Installation Conditions
See installation instructions before connecting to the supply.
WARNING This equipment is configured with multiple power sources. Hazardous voltages and
energy may be present even after the removal of a single input source. Trained
service personnel must follow guidelines stipulated in the service guidelines in the
HP Carrier Grade Server EPSS.
WARNING NORDIC Class 1 Equipment
Denmark: Før tilslutning af de øvrige ledere, se medfølgende installationsvejledning.
Sweden: Apparaten skall anslutas till jordat uttag, när den ansluts till ett nätverk.
Fuse Warnings
WARNING No internal serviceable fuses. Factory replacement of the non-operating module is
required.
Lithium Battery Warning
Battery Disposal
This hp product contains one or more Lithium ion batteries located on the cell board that may require
special handling at end-of-life.
In the Netherlands: Batteries are delivered with this product. When empty do not throw them away, but
collect them as small chemical waste.
Bij dit product zijn batterijen geleverd. Wanneer de batterijen leeg zijn, dient u deze niet als huisvuil weg
te gooien, maar als KCA in te leveren.

HP Carrier Grade Server Safety and Regulatory Information
English 7
Cabinet Safety Precautions
WARNING Cabinets are heavy even when empty. Exercise caution when moving cabinets whether
equipment is installed in the cabinet or not. Avoid rolling cabinets on rough or uneven
surfaces or inclines greater than 10 degrees. Unloading cabinets from the pallet and
movement of cabinets should be performed by at least two people.
WARNING Slideable products are not to be extended from the cabinet while the equipment is on the
shipping pallet. The cabinet must be unloaded from the pallet and both front and rear anti-tip
feet properly installed prior to extending any slideable product.
WARNING Once installed, both the front and rear anti-tip feet must remain in place to maintain stability.
Only one slideable product must be extended at a time.
WARNING Use of any slide mount product requires the installation of a cabinet anti-tip device.
The anti-tip device for the following cabinet products is a pair of anti-tip feet: A4900A,
A4901A, A4902A, A5134A, A5135A, A5136A, J1500A, J1501A, and J1502A.
Install both front and rear anti-tip feet on the cabinet before installing any slide mount
product.
The anti-tip device for the following cabinets is the installation of ballast in the bottom of the
cabinet: A1896A, A1897A, A1883A, A1884A, C2785A, C2786A, and C2787A.
To determine ballast requirements, refer to the ballast worksheets in documentation
accompanying the cabinet or http://www.hp.com/racksolutions/prodinfo/index.html.
Failure to follow these precautions can result in damage to equipment or injury to personnel.

HP Carrier Grade Server Safety and Regulatory Information
8 English
Procedimentos de Segurança - Armários
ATENÇÃO Os armários são pesados, mesmo quando vazios. Tenha cuidado ao movimentar os
armários, quer haja equipamentos instalados quer não. Evite deslizar os armários
sobre superficies acidentadas, irregulares ou com inclinação superior a 10 graus. A
retirada dos armários do palete e sua movimentação deverão ser feitas por, no
mínimo, duas pessoas.
ATENÇÃO Partes deslizantes não deverão ser abertas enquanto o armário encontrar-se no
palete de embarque. O armário deve ser descarregado do palete e os anteparos nos
pés dianteiros e traseiros devem ser instalados adequadamente antes de se abrir
qualquer parte deslizante.
ATENÇÃO Uma vez instalados, tanto os anteparos nos pés dianteiros quanto nos traseiros
devem permanecer em seus lugares adequados para garantir a estabilidade da peça.
Deve-se abrir apenas uma parte deslizante por vez.
ATENÇÃO O uso de qualquer produto de montagem deslizante requer a instalação de um
dispositivo anti-tombamento para armários.
Um par de pés anti-tombamento é o dispositivo anti-tombamento para os seguintes
armários: A4900A, A4901A, A4902A, A5134A, A5135A, A5136A, J1500A, J1501A, e
J1502A.
Instalar ambos os pés anti-tombamento na frente e atrás do armário antes da
instalação de qualquer produto de montagem deslizante.
A instalação de um lastro no fundo do armário é o dispositivo anti-tombamento para
os seguintes armários: A1896A, A1897A, A1883A, A1884A, C2785A, C2786A, e C2787A.
Para determinar os requisitos de lastro, referir-se a planilha de lastro na
documentação que acompanha o armário ou em
http://www.hp.com/racksolutions/prodinfo/index.html.
A não observância destas precauções pode resultar em danos ao equipamento ou
lesões as pessoas.