HP 345524-B21 User manual

SATA Hard Drive
Installation Guide
SATAハー ド デ ィ スク ドライブ
インストール ガイド
Document Part Number: 345524-B21
August 2003
This document provides instructions on installing a serial
advanced technology attachment (SATA) hard drive into your
computer.
このマニュアルでは、コンピュータにSerial ATA（SATA）ハードディ
スク ドライブを取り付 る方法について説明します。
345524-B21.book 1 ページ ２００３年８月２２日 金曜日 午後４時６分

345524-B21.book 2 ページ ２００３年８月２２日 金曜日 午後４時６分

1
Preparing for Installation
Although HP computers are designed for easy access to the
upgradeable areas, it is strongly recommended that only an HP
authorized dealer, reseller, or service provider install accessories.
HP authorized dealers, resellers, and service providers are
company trained in the installation of accessories and can ensure
that the accessory is installed and functioning properly.
f you decide to install the hard drive accessory yourself, you will
need a Torx T-15 screwdriver.
For additional information on SATA
technology, consult the white paper
“Implementation of Serial ATA on HP
Business Desktops” available at
http://www.hp.com/support.
345524-B21.book 1 ページ ２００３年８月２２日 金曜日 午後４時６分

Preparing for Installation
1–2 SATA Hard Drive Installation Guide
Disassembling the Computer
1. Turn off the computer and any external devices.
2. Disconnect the AC power cord and any external devices.
3. Unlock the external chassis keylock (if applicable).
4. f necessary, loosen the screws on the computer to remove
the access panel or computer cover.
5. Remove the access panel or computer cover and front bezel.
Refer to the documentation that came with your computer
for model specific instructions on accessing the inside of the
computer.
ÄCAUTION: Ensure that the power to the computer is off
and the AC power cord disconnected to avoid electrical
shock or damage to the computer.
HP accessories are for use in HP computer
products. They have been extensively tested for
reliability and are manufactured to high quality
standards. HP warrants only those accessories that
are manufactured or sold by HP.
345524-B21.book 2 ページ ２００３年８月２２日 金曜日 午後４時６分

2
Installing a Hard Drive
This chapter covers:
Qnstalling an additional hard drive.
QReplacing an existing hard drive.
If you are installing a SATA hard drive on an
hp workstation xw series, please refer to
www.hp.com/go/bizsupport for
workstation-specific installation information.
This information may be in the form of a SATA
whitepaper and/or embedded in the service
and technical reference guide
(www.hp.com/support/workstation_manuals)
for your specific workstation.
345524-B21.book 1 ページ ２００３年８月２２日 金曜日 午後４時６分

Installing a Hard Drive
2–2 SATA Hard Drive Installation Guide
It is strongly recommended that only an HP
authorized dealer, reseller, or service
provider replace your primary hard drive.
ÅWARNING: To reduce the risk of personal
injury from hot surfaces, allow the internal
system components to cool before touching.
ÄCAUTION: Ensure that the power to the computer
is off. Disconnect the AC power cord to avoid
electrical damage to the computer. Electrostatic
discharge (ESD) can damage electronic
components. Be sure you are properly grounded
before beginning this procedure. Refer to
Appendix A, “Electrostatic Discharge,” for more
information.
Refer to the documentation that came with your
computer for detailed instructions on installing an
optional drive.
345524-B21.book 2 ページ ２００３年８月２２日 金曜日 午後４時６分

Installing a Hard Drive
SATA Hard Drive Installation Guide 2–3
Installing an Additional Hard
Drive
1. f your system uses guide screws to hold the drives in the
bay, install the screws on the hard drive. These guide screws
are stored behind the front bezel.
345524-B21.book 3 ページ ２００３年８月２２日 金曜日 午後４時６分

Installing a Hard Drive
2–4 SATA Hard Drive Installation Guide
2. nstall the hard drive assembly by sliding it into the drive
bay as shown in the illustration below.
For comprehensive instructions on installing an
additional hard drive, refer to the documentation
that came with your computer.
345524-B21.book 4 ページ ２００３年８月２２日 金曜日 午後４時６分

Installing a Hard Drive
SATA Hard Drive Installation Guide 2–5
3. Locate the appropriate connectors, identified in the
following illustration, on the back of the SATA hard drive.
Hard Drive Connectors
1SATA power connector
2SATA data connector
3Debugging connector
4Legacy power connector (not present on all models)
345524-B21.book 5 ページ ２００３年８月２２日 金曜日 午後４時６分

Installing a Hard Drive
2–6 SATA Hard Drive Installation Guide
4. Connect the data cable to the SATA data connector on the
new drive as shown in the following illustration.
Five data cables are provided in the kit. Refer
to the “SATA Hard Drive Cables” card
included in the kit to determine which cable
is required for your system board.
ÄCAUTION: The data cable end is keyed to
ensure proper alignment. To avoid damage
to the cable header pins, check the
header/connector alignment and push
gently when connecting the data cable
header to the SATA connector on the drive
and system board.
345524-B21.book ページ ２００３年８月２２日 金曜日 午後４時６分