HP 6000 SERIES Assembly instructions

HP Series 6000
Mass Storage Systelll
Hardware Installation Manual
Fli;W HEWLETT
~~ PACKARD
HP Part No. 5960-0884
Printed in U.S.A. July 1991
First Edition
E0791

Notice
The information contained in this document is subject to change without notice.
Hewlett-Packard makes no warranty of any kind with regard to this material,
including, but not limited to, the implied warranties of merchantability and
fitness for a particular purpose. Hewlett-Packard shall
not be liable for errors
contained herein or for incidental or consequential damages in connection with
the furnishing, performance, or use of this material.
Hewlett-Packard assumes no responsibility for the use or reliability of its
software
on equipment that is not furnished by Hewlett-Packard.
This document contains proprietary information, which is protected by
copyright.
All rights are reserved. No part of this document may be
photocopied, reproduced, or translated to another language without the prior
written consent of Hewlett-Packard Company.
RESTRICTED RIGHTS LEGEND
Use, duplication or disclosure by the U.S. Government is subject to restrictions
as
set forth in Subparagraph (c) (1) (ii) of the Rights in Technical Data and
Computer Software clause at DFARS 252.227-7013 for DoD agencies, Computer
Software Restricted Rights clause at FAR 52.227-19 for other agencies.
Hewlett-Packard Company
3000 Hanover Street
Palo Alto,
CA 94304 U.S.A.
© Copyright 1991 by Hewlett-Packard Company.

BP Series 6000
Hardware Installation Manual
Printing History
New editions are complete revisions of the manual. Update packages, which are
issued between editions, contain additional and replacement pages to be merged
into the manual by
the customer. The dates on the title page change only when
a new edition or a new update is published. No information is incorporated into
a reprinting unless
it appears as a prior update; the edition does not change
when an update is incorporated.
Many product updates do not require manual changes and, conversely, manual
corrections may be done without accompanying product changes. Therefore, do
not expect a one-to-one correspondence between product updates and manual
updates.
July 1991
First Edition
iii

Hardware Installation Manual HP Series 6000
Safety Symbols and Conventions
The following conventions are used throughout this manual:
• Italic is used for emphasis or manual titles.
Note
Caution
,
Warning
iv
Notes contain important information set off from the text.
Caution messages indicate procedures which, if
not observed,
could result in damage to equipment.
Do not proceed beyond
a
CAUTION sign until the indicated conditions are fully
understood and met.
Warning
messages indicate procedures or practices which,
if not observed, could result in personal injury. Do not
proceed beyond a WARNING sign until the indicated
conditions are fully understood and met.

Contents
1. Mass Storage System
Installing Your Mass Storage System .
Unpacking
..... .
Handling
........ .
Electrostatic
Discharge. . .
Connecting
the Power Cord
Host Computer System Connection
Connecting
the SCSI Cable ...
Setting the SCSI Address Switches
Adding Devices . . . . . . . . . .
Preparing
to Install a SCSI Device .
Removing
the Front Panel
Removing
the Top Cover .
Removing
the RFI Bracket
Installing the SCSI Devices .
Reinstalling
the Top Cover
Reinstalling the Front Panel ....
Mounting the Mass Storage System in a Cabinet .
Configuration
Record. .
Device Serial Numbers
....... .
2. 5.25-inch Hard Disk Drive Installation
Unpacking the Upgrade Kit. . . . . . .
Options/Address Jumpers ...... .
Installing
the 5.25-inch Hard Disk Drive ..
Connecting the Cables . . . . . . . . .
1-2
1-2
1-2
1-3
1-5
1-7
1-8
1-9
1-10
1-10
1-11
1-11
1-14
1-14
1-18
1-18
1-19
1-21
1-21
2-1
2-3
2-5
2-9
Contents·1

8. 8.5-inch Hard Disk Drive Installation
Unpacking the Upgrade Kit. . . . . .
Options/Address
Jumpers. . . . . .
Adding a Second 3.5-inch
Hard Disk Drive .
Installing
the 3.5-inch Hard Disk Drive
Connecting
the Cables . . . . . . .
4. DDS-format DAT Drive Installation
Unpacking the Upgrade Kit. . . . . .
Options/Address
Jumpers. . . . .
Installing
the DDS-format DAT Drive
Connecting
the Cables . . . . . . .
5. Rewritable Optical Disk Drive Installation
Unpacking the Upgrade Kit. . . . . . . . .
Options/Address
Jumpers ........ .
Installing
the Rewritable Optical Controller PCA
Connecting the Cables to the Controller PCA
Installing the Rewritable Optical Disk Drive
Connecting Cables
to the Drive . . . . . . . .
6. CD-ROM Drive Installation
Unpacking the Upgrade Kit .
Options/Address
Jumpers .....
Adding a Second CD-ROM Drive
Installing
the CD-ROM Drive ....
Connecting the Cables . . . . .
Index
Contents~2
3-1
3-3
3-5
3-7
3-11
4-1
4-3
4-5
4-8
5-1
5-3
5-5
5-8
5-10
5-12
6-1
6-3
6-5
6-7
6-10

Figures
1-1. Packaging Details . . . . . . . . . . . . . . . 1-4
1-2. Controls
and Connectors . . . . . . . . . 1-6
1-3. Removing
the Front Panel and Top Cover 1-12
1-4. Mass Storage System Chassis . . . 1-13
1-5. Removing
the RFI Bracket . . . 1-15
1-6. Removing
the Front Panel Bezels . . 1-16
1-7. Connecting
the DC Power Cable 1-17
1-8. Installing
the Mass Storage System into C2785A/86A Cabinets 1-20
2-1. 5.25-inch Hard Disk Drive Upgrade Kit Contents. . . 2-2
2-2. 5.25-inch Hard Disk Drive
Connectors. . . . . . . . 2-4
2-3. Installing
the 5.25-inch Hard Disk Drive into Slot 1 2-6
2-4. Installing
the 5.25-inch Hard Disk Drive into Slot 2 2-7
2-5. Installing
the 5.25-inch Hard Disk Drive into Slot 3 2-8
2-6. Connecting Cables to
the 5.25-inch Hard Disk Drive 2-10
3-1. 3.5-inch Hard Disk Drive Upgrade Kit Contents . . 3-2
3-2. 3.5-inch Hard Disk Drive Connectors . . . . . . . . 3-4
3-3. Installing a 3.5-inch Hard Disk Drive into a Mounting Bracket 3-6
3-4. Installing
the 3.5-inch Hard Disk Drive into Slot 1 3-8
3-5. Installing
the 3.5-inch Hard Disk Drive into Slot 2 . 3-9
3-6. Installing
the 3.5-inch Hard Disk Drive into Slot 3 . 3-10
3-7. Connecting Cables to the 3.5-inch Hard Disk Drive. 3-12
4-1. DDS-format
DAT Drive Upgrade Kit Contents . 4-2
4-2. DDS-format
DAT Drive Connectors . . . . . . . . 4-4
4-3. Installing
the DDS-format DAT Drive into Slot 1 4-6
4-4. Installing
the DDS-format DAT Drive into Slot 3 4-7
4-5. Connecting Cables to
the DDS-format DAT Drive. 4-9
5-1. Rewritable Optical Disk Drive Upgrade Kit Contents 5-2
5-2. Rewritable Optical Disk Drive Connectors . . . . . . 5-4
5-3. Installing
the Rewritable Optical Controller peA . . 5-6
5-4. Sliding
the Controller PCA into the PCA Guides (top view) . 5-7
5-5. Connecting Cables to
the Rewritable Optical Controller PCA 5-9
5-6. Installing
the Rewritable Optical Disk Drive . . . . . . . . 5-11
Contents·3

5-7. Connecting Cables to the Rewritable Optical Disk Drive
6-1.
CD-ROM Drive Upgrade Kit Contents . . . . . . .
6-2. CD-ROM Drive Connectors . . . . . . . . . . . .
6-3. Installing a
CD-ROM Drive into a Mounting Bracket
6-4. Installing a
CD-ROM Drive into Slot 1 .
6-5. Installing a CD-ROM Drive into Slot 3 ..
6-6. Connecting Cables to a CD-ROM Drive
Contents·4
5-13
6-2
6-4
6-6
6-8
6-9
6-11

Thbles
1-1. Mass Storage System Address Switches
1-2.
SCSI Device Configuration Record. . . 1-9
1-22
Contents·5

1
Mass Storage System
This manual describes installation of the mass storage system. Details of the
host computer control functions are described in the computer's documentation.
Note
This installation manual is written for personal computer
dealers, technicians, and others who are familiar with setting
up mass storage devices.
If you are not experienced with such
tasks, please find an experienced person to help you, or contact
your local Hewlett-Packard Sales and Support Office.
Mass Storage System 1·1

Hardware Installation Manual HP Series 6000
Installing Your Mass Storage System
This section describes how to install your mass storage system. These
instructions include unpacking instructions, a check of equipment supplied,
and how to connect the mass storage system to a power source and the Small
Computer System Interface (SCSI) bus.
Unpacking
The mass storage system is shipped in a reusable shipping container as shown
in Figure 1-1. Remove the mass storage system from this container and inspect
it for any damage that may have occurred during shipment. If any damage
is observed, immediately notify your dealer or a Hewlett-Packard Sales and
Support
Office.
Handling
Although the mass storage system has been designed to withstand a certain
shock level, it is still a delicate device. Observe the following precautions when
handling
or transporting the mass storage system. Failure to observe these
handling precautions could result in loss of data or damage to the product.
• Avoid sudden shocks to the mass storage system.
• Always package the mass storage system in approved containers when
transporting the product from one
area to another. Use the original packaging
material
or a similar substitute.
1·2 Mass Storage System

HP Series 6000
Hardware Installation Manual
Electrostatic Discharge
Caution
, • A static charge of 39,000 volts can be generated on a
carpeted
floor. If you do not protect against electrostatic discharge, you
may damage your product
and void your warranty.
• Handle the devices with care. Devices are susceptible to
mechanical shock and vibration until
they are secured into
the mass storage system chassis.
To ensure continuously successful operation of this product in a carpeted office
environment, Hewlett-Packard recommends
the use of anti-static mats and
anti-static carpets with this product. Refer to the Hewlett-Fhckard Computer
Users Catalog, part number 5953-2450D, for a complete list of static-control
equipment, including anti-static mats and carpets.
Mass Storage System 1·3

Hardware Installation Manual
HP Series 6000
4
Figure 1-1. Packaging Details
I-Foam Cushions (C2200-80016)
2~ Mass Storage System
3-Antistatic Bag (9222-1030)
1-4 Mass Storage System
4-Shipping Carton (C2200-80017)
5~Manuals
6- Power Cord (part number
depends upon location)

HP Series 6000
Hardware Installation Manual
Connecting the Power Cord
The various power cords available are shown in the Disk Product Specifications
and Site Environmental Requirements Handbook, part number 5955-3456. Each
mass storage system is shipped with an appropriate power cord.
Warning
Note
• The ac branch service must be properly current-protected
by either a fuse or a circuit breaker.
• Use only a UL/CSA approved power cord, SVT type, rated
for suitable voltage and current. These power cords have
two conductors plus a ground. Failure to use the proper
power cord could result in a shock or fire hazard.
• Do not open the power supply. The power supply contains
no customer-serviceable parts.
Your mass storage system has an automatic ranging power
supply. This means that a voltage selector switch and external
fuse are unnecessary. Automatic ranging power supplies have
internal fuses
that only fail if the power supply malfunctions.
To attach the power cord:
1. Set the [LiNE-) switch to the 0 (out) position.
2. Connect
the female end of the power cord to the -AC LINE connector at the
rear of the mass storage system.
Mass Storage System 1·5

Hardware Installation Manual
BP Series 6000
'1
1 r=
vP""
t=1
~
=t=;::;:::::;
/
\. 1 2 3 4/
\:
J
CD
./
~..../
0
QITnu
ooooooooooo~ooooooooooo
oOoooooooOotoOooooooooo
oOooooooooocJoooooooooo
oooooOOOOOOc)OOOOOOoooo
000000000000)0000000000
000000000000(0000000000
000000000000 0 0 000000
0808080800 ffi \1]1 008
0
~0o
0000000000 0 0 0000
80808080800 goo 0
000000000000 0 0 00
000000000000000000000
000000000000000000000
0 0
421 421 421 421 421
~~
~ ~ ~ ~scs<R:
:F0<J:r
1 2 3 4 5
'--
)
cubeon ®
Figure 1-2. Controls and Connectors
l-(LlNE~) Switch
2-5.25-inch Hard Disk Drive Status
Indicators (amber)
3- Power-On Indicator (green)
1·6 Mass Storage System
4-SCSI Address Switches
5-SCSI Connectors
6--AC LINE Connector

BP Series 6000 Hardware Installation Manual
Host Computer System Connection
Caution
,
Note
• Switch off power from all units of your host computer before
connecting (or disconnecting) the mass storage system.
• Use only cables listed under" Accessories Available" in the
Quick Reference Guide to connect the mass storage system
to
the SCSI bus. Failure to use these shielded cables may
cause noncompliance with Radio Frequency Interference (RFI)
specifications.
• When you are ready to return power to your system, first
apply power to the mass storage system, then to the host
computer.
For host computer system configuration information, please
refer to the Quick Reference Card included with
your mass
storage system. The Quick Reference Card shows the title of the
configuration manual(s) for the various operating systems.
Mass Storage System '·7

Hardware Installation Manual HP Series 6000
Connecting the SCSI Cable
One or more mass storage systems can be connected to the host computer.
Before connecting to the host computer, ensure that the cabling conforms with
the following SCSI cabling standards.
Caution
,
Your mass storage system is a single-ended SCSI device. Do not
mix differential-ended SCSI hosts with single-ended mass storage
systems. Connecting a differential host to a single-ended mass
storage system could damage both
the host and the mass storage
system.
• The SCSI bus allows a maximum of eight devices, including the host computer
system. SinceI your mass storage system can contain from one to five SCSI
devices, you must make sure you know the number of SCSI devices within
your mass storage system before connecting it to the system bus. It is possible
that two fully loaded mass storage systems could exceed the SCSI device limit.
• The total length of the SCSI cables must not exceed six meters. In addition to
external cables, each mass storage system contains 1.75 meters of internal
SCSI cabling. This dimension must be included in cable length calculations.
• The last mass storage system on the bus must have a SCSI terminator (part
number K2291) fitted
on its unused SCSI connector.
1. Disconnect power to the host computer and the mass storage system.
2. Connect the host computer
SCSI cable to either of the two SCSI connectors
on the rear panel of the mass storage system. Ensure that the connector
retaining clips are locked in place.
3. Connect the
next SCSI device or the SCSI terminator to the other SCSI
connector on the mass storage system.
'·8 Mass Storage System

HP Series 6000
Hardware Installation Manual
Setting the SCSI Address Switches
Note
For optimum system performance, your system disk SCSI address
should always be
set to the highest SCSI address available
(usually address number 6).
Each device on a
SCSI bus requires a unique SCSI address (0-6). (The SCSI
interface card in the host computer is normally set to 7.) The SCSI address
switches on the mass storage system rear panel of the (see Figure 1-2) allow
an address to be selected for each SCSI device in your mass storage system.
Set each three-position DIP switch for each device as desired. Thble 1-1 shows
one the settings and resultant address for one of the switches. Set a different
address for each installed device. Make sure that no two devices have the
same SCSI address. You must cycle power for new address switch settings to be
recognized.
'Dtble 1-1. Mass Storage System Address Switches
SCSI
Switch
Switch Switch
Address
4 2
0 0 0
1 0 0
2 0 1
3 0 1
4 1 0
..
5 1 0
6 1 1
71 1 1
1 Address 7 is nonnally reserved for the Host Bus
Adapter.
1
0
1
0
1
0
1
0
1
Mass Storage System '·9

Hardware Installation Manual
HP Series 6000
Adding Devices
Your mass storage system may come with devices pre-installed, or you may
install them
at a later time as upgrade kits. The following instructions should
be followed when adding a
new device.
Warning
o
Caution
,
After a SCSI device is installed in the mass storage system,
the mass storage system must be carefully reassembled to
ensure compliance with RFI emission requirements, and to
provide adequate protection against electrical shock and
fire hazards.
The mass storage system has been designed for optimum
performance when using the mass storage devices from
Hewlett-Packard.
To ensure that the mass storage system meets
its published performance, regulatory, and safety specifications,
we recommend you use only Hewlett-Packard accessory mass
storage devices.
Preparing to Install a SCSI Device
1. Shut down (halt) the host computer.
2. Turn off power to both the host computer and the mass storage system.
3. Disconnect the power cord from the mass storage system.
4. Disconnect the SCSI cable from the mass storage system.
5. If necessary, remove the mass storage system from its rack or cabinet (see
Figure 1-8).
1·10 Mass Storage System