HP 705 Quick start guide

For:cote
Printed on:Mon, Feb 3, 1997 12:58:44
Document:a1658-90692
Last saved on:Mon, Feb 3, 1997 12:48:23

You will not be able to load HP-UX 9.03 on a standalone, newly installed
2–GB drive. To install HP–UX 9.03 on 2–GB drives, you
must use a netdist install server. You must install patch PHSS_5776 on the netdist install server to
recognize 2-GB drives for both HP-UX 9.03 and 9.05. After you have loaded HP-UX onto the either the 2–GB or 4–GB drive, you must load patch PHCO_7461 for disktab and sam func- tionality. Install the patches using /etc/update. To load HP-UX 9.05 onto a newly installed standalone 2–GB drive,
prior to loading the patches, perform the following steps:
1. Begin the HP-UX software installation process. The follow-
ing message appears: “Note: the destination disk type “
disk–drive–model–number
” was not found in
the disk table /etc/disktab. (Press any key to continue.)”
2. Press any key. The screen displays the following message:
“If model number: “
disk–drive–model–number
”,
is incorrect, and a correct one (one that has an entry in the /etc/disktab) is known, please enter it now otherwise press return.”
3. Press: <Return> (or <Enter>)
The screen displays a message about using default parameters. 4. Press any key. 5. Let the software installation process complete.
The software patches may be obtained from HP Customer Service.
INSTRUCTIONS FOR HP-UX 9.X
After you have loaded HP–UX onto the new drive, install the appropriate patches using swinstall and reboot the system.
INSTRUCTIONS FOR HP-UX 10.X
2- and 4-GB (Fast-Wide-Differential)
Disk Drive User Notes
Refer to your workstation owner’s guide or your disk drive installation guide for detailed information about installing your disk drive. During the installation procedure, you may have to change the SCSI ID of your disk drive. Refer to the appropriate illustration to set the SCSI ID jumpers to the desired SCSI ID.
NOTICE: We recommend that you use SCSI ID 6 for your
workstation’s first hard disk drive, and SCSI ID 5 for the second hard disk drive.
  
The 2-GB disk drive is fully operational with HP-UX Release 9.03 and later on Series 700 binary–compatible systems. The 4-GB disk drive is fully operational with HP-UX Release 10.01 and later on Series 700 binary–compatible systems, and at HP-UX Releases 9.05 and 9.07, this drive may be used as a non-bootable device. Patches are required to most operating systems. Please see the following table and the patch instructions on the last page of this document.
HP-UX
Version Patches
– OS
Patches – Diags
9.03 (2–GB) PHCO_7461, PHSS_5776 PHSS_7587
9.05 PHCO_7461, PHSS_5776(2–GB) PHSS_7587 9.07 N/A PHSS_7587
10.01 PHKL_8904, PHKL_8329 PHSS_7583 10.10 PHKL_8906 PHSS_7585 10.20 PHKL_8908 PHSS_7929
Part Number A1658–90692
Edition E1296
Printed in U.S.A.


CAUTION
NOT
Do plugs for J2 on J6. Y
ou will damage the
internal contacts
use the jumper
A2
A1
A0
0 1 2 3 4 5 6
SCSI
J6
J2
M S B
L S B
ID
A3
8 9 10 11 12 13 14 15
Highest Priority
Lowest Priority
Term Power From Drive
Seagate ST32171WD and ST34371WD Disk Drive Jumpers
0 1 2 3 4 5 6
SCSI ID
M S B
L S B
15 14 13 12 11 10 9 8
Highest Priority
Lowest Priority
Spin
up
on power up
Quantum – Atlas II – XP32181WD and XP34361WD Disk Drive Jumpers
The HP part numbers for the 2–GB drives are A1658–60010 (spare) and A1658–69010 (exchange).
The HP part numbers for the 4–GB drives are A1658–60011 (spare) and A1658–69011 (exchange).