HP StoreOnce B6000 Operating manual

Executive Summary .............................................................................................................................. 2
Scenario Summary ....................................................................................................................... 4
Introduction: Issues Associated with Remote Office/Branch Office Backup.................................................. 5
Solution Scenarios ............................................................................................................................... 7
Scenario 1 –Client based backup over the WAN using HP Data Protector synthetic full functionality.......... 7
Scenario 2 –Low Bandwidth Replication using HP D2D and HP Data Protector for up to 24 remote sites .... 9
Scenario 3 –Low Bandwidth Replication using HP VLS and HP Data Protector for Regional data centers... 11
Summary....................................................................................................................................... 13
Glossary of Terms .......................................................................................................................... 14
Appendix A – HP VTL Family with Deduplication and Low Bandwidth replication ...................................... 18
Appendix B – HP Data Protector Synthetic Full Backup ........................................................................... 19
Appendix C – Deduplication is the enabler for Low Bandwidth replication. .............................................. 21
Appendix D – HP Data Protector Product Structure & Support Matrix........................................................ 23
Call to action .................................................................................................................................... 25
ROBO and regional data centre data protection
solution scenarios using HP Data Protector software,
HP VTL systems and Low Bandwidth replication

Executive Summary
Protecting data across all corporate locations is critical for business, legal and regulatory compliance
purposes in today’s information age. Too often, business critical data at remote locations is
inadequately protected, exposing the business to the risk of lost data and lost productivity. A study
conducted by industry analyst Enterprise Strategy Group found that the top three IT priorities for
remote office / branch office (ROBO) locations were driven by business priorities: Improve
information security, ensure regulatory compliance, and improve disaster recovery1.
Some of the biggest challenges in remote office data protection cited by organizations are:
-Limited IT staff and limited backup & recovery skill set
-High capital and operating costs of remote office backup & recovery
-Inability to complete backup jobs within scheduled backup window
-Improving the time it takes to recover data
Centralizing the control, management and policies of remote location backup and recovery
1Enterprise Strategy Group Research Report: Branch Office Optimization, 2007
This whitepaper shows how recent developments in the HP data protection portfolio can overcome
these obstacles through the use of centralized management with HP Data Protector software and the
use of Deduplication and Low bandwidth replication on HP’s virtual tape library products. The
whitepaper examines three scenarios which cover a wide range of possible implementations.
Figure 1: Enterprise deployment with small and large ROBOs
Figure 1 shows the HP Vision for “Protecting data anywhere” using these technologies.

The HP Vision for ROBO based data protection is that backup data should be accessible wherever it
is required which in some cases requires it to be in 3 locations as well as on physical tape. This gives
maximum flexibility in restore options or DR options. When managed through a single backup
application this allows the personnel with relevant expertise to recover the data from multiple
locations , be it recovering data at the ROBO site from the ROBO appliance but managing the
recovery from the data centre or regional data centre, or even recovering at the ROBO site itself if the
relevant expertise is present. The HP vision also realizes that backup appliance demands for ROBO’s
and data centers are very different both in terms of price and performance which is why the HP vision
uses different technologies appropriate to these different customer requirements. Multi-hop replication
and further combined appliance storage consolidation in the data centre are possible future
enhancements to this vision. As we discuss various scenarios below it is worth noting some unique
functionality enhancements between HP data protector and HP D2D & VLS appliances to allow this
vision to be delivered today.

Scenario Summary
Scenario 1 Scenario 2 Scenario 3
Typical sizing
200+ ROBO’s with full
backup size of 100GB
& incremental backups
of 10%
100+ ROBO’s with
200-500GB full
backups
100+ ROBO’s with
200-500GB full
backups
PLUS
Up to 4 regional data
centres with 7.5TB to
300TB backups
requiring DR solution
Problem
Large number of ROBO
sites with small backup
volumes
Significant backup
volume at remote sites
and a requirement for
local recovery at the
ROBO site.
All above data
requiring to be
consolidated at main
data centre
Solution
HP Data Protector
Synthetic full backups
over WAN to HP D2D
with NAS Emulation
Up to 24:1 fan-in from
small D2D units in
ROBO to larger
consolidated single
D2D in data centre
Offload to Physical
tape if required
HP D2D for ROBO’s,
HP VLS for Regional
Data Centres
D2D to VLS copies at
regional data centre
using HP data protector
and onward replication
to main data center
Why HP
Synthetic full
functionality allows
object consolidation
and ensures only small
volumes of data
transmitted over WAN.
Scalable up to 100s of
ROBO sites
Recovery to ROBO
from data centre under
data centre control
Only HP offers a low
cost entry point to
deduplication and low
bandwidth replication
for ROBO’s ( sub
$3000 )
Target D2D can be
tape to tape copied to
physical tape using
special functions in HP
Data Protector
End to End control
from HP data protector
Only HP offers both a
low cost entry point to
deduplication and low
bandwidth
replication(D2D) AND
a highly scalable, high
performance
deduplication
appliance (VLS) for
Enterprise
environments.
Target VLS can be tape
to tape copied to
physical tape using
special functions in HP
data protector
End to End control
from HP data protector

The key learnings from a study of these scenarios are:-
Using physical tape at ROBO’s and performing daily off-siting of physical media will become a
thing of the past, physical tape will be replaced by WAN based backup or a HP virtual tape
libraries so that the whole process is automated and managed from a regional centre or main data
centre. The automation will vastly improve the reliability of backup in the most remote offices where
there are typically no trained IT staff.
Deduplication technology is the key enabling technology for Low bandwidth replication which is
revolutionizing ROBO backup. Deduplication enables the “unique” pieces of data to be identified
and replicated, in turn this means much smaller inter-site links are required to effectively transmit
large apparent quantities of data. Up to 95% bandwidth saving is achievable. Low bandwidth
replication now ensures we can cost effectively “protect data anywhere”. Low bandwidth
replication can be “throttled” to use a percentage of an existing link, so as not to affect applications
performance running on the same link. One key advantage for HP is its ability to provide “scale
down” deduplication devices that are very cost effective and an ideal fit for ROBO’s.
Consolodation of replicated data from many ROBOs onto a single device at the regional data
center or main data center allows for further cost efficiencies.
Physical tape does still have a role to play in larger regional centres and main data centres, as a
long term archive media for customers that have a need to keep data for years. It is relatively
simple to integrate physical tape into a virtual tape environment because all backup software
supports tape to tape copy. Certain compliance regulations also demand additional copies of data
be made to physical tape.
Close integration of HP D2D & VLS devices with HP data protector software allow for complete end
to end solutions to be realized. Features such as synthetic full backup, Object copy and the ability
for HP Data protector to detect replicated cartridges and incorporate them into its internal catalog
database ensure the solution is always “Disaster recovery ready”. Management of the whole
process from anywhere in the network ensures a tight integration and expeianced IT staff access to
all the relevant components.
Introduction: Issues Associated with Remote Office/Branch
Office Backup
For many years remote office/branch office backup and restore has been an issue with IT managers.
Some of the challenges they faced were:-
Having to implement physical tape infrastructure and operators at what could be a large
number of sites.
Paying service providers to pick-up store and retrieve tapes to and from an off-site facility.
Data in transit (physical tapes) are prone to being lost, and the company relies entirely on a
3rd party for their ability to recover from a disaster.
Untrained IT personnel at the most remote sites, who may have been responsible for changing
physical tapes, and then off-siting the tapes. A very manual but important process which may
not always have been executed well.
Reliability of the process – more prone to errors because it was manual and required regular
human intervention. Physical tape drive cleaning and tape rotation added to the complexity.

Errors and failures not always accurately diagnosed. Low restore success rate at a local level
was probably a major issue.
If the backups were large or slow and only a single backup device was available – the
backup window could be large and extend into the normal business hours affecting critical
business applications.
Backup over the company WAN to a central site was restricted because of the relatively high
volumes of data that needed to be backed up over a relatively low speed link.
It was very difficult to prove to auditors that a comprehensive site disaster recovery plan was
in place and effective.
The solution to these issues is:-
To automate the process End to End with a single management console across the entire
estate.
Extensive use of virtual tape libraries with deduplication and low bandwidth replication to
automate the process. This allows flexible provisioning of backup resources to meet changing
customer needs, and offer more effective storage utilization, ability to reduce backup
windows and provide faster single file restores.
Make the best use of existing WAN links from ROBO sites to Regional data centres and from
regional data centers into main data centers by using Synthetic full backups and Low
Bandwidth replication.
Perform backup object consolidation by using technologies such as HP data protector
synthetic full backups ( See Appendix B): Only one initial full backup; no file is stored
multiple times, and therefore, can reduce required backup space/media.
Only changed files need to be backed up, this enables fast backup of file servers hosting
millions of files allowing more frequent backup.
Spend Less time on physical tape management: There is no tedious tape management with
synthetic full backups or virtual tape libraries..
To be able to maintain and manage Backup copies in multiple locations depending on
retention policies and disaster recovery (DR) policies

Solution Scenarios
The scenarios discussed below cover a wide range of implementations that are possible using HP
Virtual Tape Libraries and HP Data Protector software, from a small business that has several outlets to
a major corporation that has hundreds of remote/branch offices, several regional data centres and
multiple main data centers.
Scenario 1 –Client based backup over the WAN using HP Data
Protector synthetic full functionality.
Figure 2: Client based backup over the WAN using HP Data Protector Synthetic Full functionality
Key Message: Cost effective Remote Office Backup with low WAN traffic
In this first scenario we follow a basic client agent backup process, suitable for a large number of
ROBO sites where relatively small amounts of data need to be protected. In order to minimize the
amount of data that needs to be transmitted over the WAN we can use the “synthetic full” feature of
HP Data Protector. After the initial full backup we only need to perform incrementals thereafter. The
backup data is sent to a “File Library” device ( in this case a NAS share with deduplication on the
D2D4000 unit), where a “synthetic full” can be created at any time for a restore. Alternatively there is
another feature in HP Data Protector called virtual full that is similar to synthetic full but uses less
storage space, but can only be implemented on a file library device such as an HP MSA2000 disk
array. Finally again under data protector control the synthetic fulls can be copied to physical tape for
long term archiving.

The key benefits to the customer of this solution are:-
Object consolidation using synthetic full backups to minimize WAN traffic
Variable Retention policies. Short term on D2D, Long term on tape for archive.
Fast recovery from D2D4000 with NAS* emulation
HP Data Protector manages the entire process from the main data centre.
Reduced WAN utilization (because small incremental backups)
This solution does not provide a local source of the data for recovery. A synthetic full created at the
regional centre is required and the necessary files to be restored need to be transferred over the
WAN. This could take some time depending on size.
*Available late 2009

Scenario 2 –Low Bandwidth Replication using HP D2D and HP Data
Protector for up to 24 remote sites
Figure 3 : End to End Low Bandwidth replication solution with regional centre consolidation, all under HP Data Protector
Control
Key message: Backup Consolidation & Cost effective Disaster Recovery for larger ROBO’s
In this next example the volumes of data on the remote sites are much larger; 500GB perhaps, and
the customer really needs to have local restore capability. So in this scenario each remote site has a
local D2D2500 with deduplication and the D2D is using virtual tape library emulation mode. A user
capacity of 1.5TB can yield up to 30TB of backup storage with a 20:1 deduplication ratio, after
several backups have been retained over 2-3 months. If long retention is not required then the
D2D2500 can support even larger backups but retained for shorter periods. Direct restore at the
ROBO from the D2D unit is always possible because each ROBO site contains a complete Data
Protector environment of cell manager and media server and is “self-sufficient” from a restore
perspective. The local D2D2500’s (sources) can also be configured to replicate only the changed
data across a low bandwidth link to the regional centre where a larger D2D4112 device resides. A
D2D4112 can support a fan-in of up to 24 D2D sources, and only requires a single licence to enable
replication. This allows major storage consolidation benefits at the regional data centre. The
replication process replicates the changes in virtual cartridges from the ROBO to the regional centre.
On a regular basis the HP data protector cell manager 1 polls the D2D4112 to detect replicated
cartridges so it can update its internal database (IDB) with their contents. This ensures that in the event
of a disaster at the ROBO the regional centre is immediately aware of which virtual tapes are
required for recovery. Finally data from the D2D4112 at the Regional centre can be easily copied to
physical tape at regular intervals using the “object copy” functionality within HP Data Protector.

The D2D4112 as well as acting as a replication target for the ROBO sites can also act as a source
for backups from the regional centre servers as can be seen in Figure 3.
This solution provides robust disaster recovery, should a total disaster occur at the source (ROBO), the
data is safely already offsite at the target ( regional data centre). The ROBO site can then be re-
constructed by either:-
a) Re-building a new ROBO server and restoring data at the regional centre using the
replicated data
b) Rebuilding the server at the ROBO site and reverse replicating the critical data from the
D2D4112 in the regional centre. Reverse replication involves the total contents of the backup
being copied back from the replication target to the source, and may take some time if larger
quantities of data are required to be reverse replicated over a low bandwidth link..
c) Offloading critical data to tape at the regional center and transporting back to the ROBO
with the necessary tape hardware for recovery.
The key new area of interest here is the Low Bandwidth link. For the majority of ROBO sites link
speeds as low as 2Mbit/sec can be used ( dependent on volumes of data to be replicated). The HP
suggested usage models for low bandwidth replication are
Use 100% of the link bandwidth to complete replication in a fixed window (12Hrs). This is for
businesses that are not necessarily 24x7 and can afford a window dedicated to replication.
Within the D2D unit it is possible to configure “throttling” of the link and allow the replication
to take place over a 24 hour period. This is for businesses that also use the WAN link for
applications, and where giving the whole link over to replication would affect application
performance.
To calculate the size of the regional centre D2D device and the size of the link required (either with
fixed window or with throttling) HP provides a comprehensive sizing tool available from:-
http://www.hp.com/go/storageworks/sizer
As for scalability - In the example above we show 24:1 fan-in, if we had > 24 ROBO sites we would
have multiple separate D2D4112 devices at the regional data centre.
The key benefits to the customer of this solution are:-
Backups performed and controlled locally, reliability of backups not dictated by WAN
availability and remote media server as in scenario 1
Fast local recovery when needed.
Ability to store several months of backups locally at ROBO with D2D deduplication.
Significant bandwidth reduction – up to 95% savings in bandwidth compared to all contents
being replication rather than just changed data detected by deduplication.
Cost effective consolidation in the regional centre up to 24 ROBO D2Ds (fan-in) AND
D2D4112 can be used for local regional centre backups as well.
Very Flexible Disaster recovery options.
Easy offload to tape with HP Data Protector Object copy.
HP Data Protector manages the entire process from the main data centre.
Option to manage single ROBO’S from the Regional Centre or Data Centre

Scenario 3 –Low Bandwidth Replication using HP VLS and HP Data
Protector for Regional data centers.
Figure 4: Regional data centre to Main data centre End to End replication with HP VLS all under HP Data Protector control
Key Message: Scalability, Consolidation and Data Centre resilience
In this scenario the volumes of data involved at the regional data centres are significantly high and
the need for scalability paramount. HP’s enterprise level Virtual Tape Libraries (VLS) are therefore
used because in terms of deduplication (the technology enabler for low bandwidth replication) the HP
VLS accelerated deduplication is able to scale much higher in terms of capacity and performance
than the HP Dynamic deduplication used on HP D2D systems.
The ROBO to regional centre solution is the same as in Scenario 2 but instead of local regional data
centre backups being done to D2D because the regional data centre volumes are > 30TB they are
now backed up to a local VLS9000 device. VLS systems also support Low Bandwidth replication and
currently support up to 4 to 1 fan-in, so we can consolidate replications from several regional data
centres in a single VLS9000 device at the main data centre. The VLS9000 uses a multi-node
architecture to ensure scalability in terms of backup performance, deduplication performance and
replication performance. Because of the higher volumes of replicated data involved however the low
bandwidth links for VLS are typically in the area of 100 Mbits/sec upwards. This solution with VLS
allows consolidation at the main data centre, the VLS9000 there is used both as a replication target
for the 4 regional data centres AND for main data centre backups as well, providing a very good
consolidated solution. Deduplication is a licensable feature on the VLS range , and low bandwidth
replication licencing is only required at the target site(one licence per node).

Replicated cartridges from the regional centre arriving at the VLS target in the main data centre send
an Email on an hourly basis to the Data Protector Cell manager at the main data centre. Data
Protector scripts then import these newly replicated tapes into the backup catalog at the main data
centre to allow easy access to replicated data in the event of disaster recovery being necessary for
the regional data centre.
Should it be required for compliance or archiving HP Data Protector Cell manager 1/Media Server at
the main data centre can easily copy any content from the VLS to Physical tape.
A further enhancement to this scenario would be to have Active <-> Active replication where the
main data centre backups to the VLS are also replicated back to the regional data center giving the
main data centre a very cost effective disaster recovery process using existing infrastructure.
Because of the different nature of D2D & VLS deduplication technologies it is not possible for D2D
units to replicate directly into a VLS unit.
The disaster recovery options for the regional data centre using VLS are identical to those used for
D2D namely:-
a) Re-building regional server and restoring data to it at the main data centre using the data
replicated to the main data centre VLS.
b) Rebuilding the server at the regional site and reverse replicating the critical data from the
VLS in the main data centre. Although this will be limited to several TB max, because of the
replication link being the bottleneck to high capacity restores – for reverse replication the
“entire” contents of a virtual tape are reverse replicated.
c) Offloading critical data to physical tape at the main data centre and transporting physical
tapes and associated hardware back to the regional data centre for import and recovery.
Again with the higher volumes of data involved between regional data centres and main data
centers HP expect the usage model for VLS to VLS replication to be predominantly
A dedicated replication link – not shared with application traffic
24 Hour replication window available.
VLS replication sizing is also fully supported in the HP StorageWorks sizing Tool
http://www.hp.com/go/storageworks/sizer
The key benefits to the customer of this solution are:-
Fast local recovery when needed at both ROBO, regional data centre and Main data centre.
Option for ROBO data to be copied to VLS in regional data center for onward replication to
main data centre.
Ability to store several months of backups locally at regional data centre and main data
centre using VLS accelerated deduplication - scalable to very high volumes.
Cost effective consolidation in the main data centre, up to 4 regional VLS units (fan-in) AND
VLS at main data centre can be used for local main data centre backups as well.
Very Flexible Disaster recovery options.
Easy offload to tape with HP Data Protector Object copy.
HP Data Protector manages the entire process from the main data centre.
Main Data centre DR capability if active<->active replication is deployed in the future, using
existing infrastructure.

Summary
The three scenarios described above give an insight into the various ROBO & regional data centre DR
deployments possible using HP storage components:-
HP Data Protector product features ( synthetic full backup, Object copy, automated tape
importing etc)
HP D2D systems – with Dynamic deduplication as standard and products specifically
designed for the ROBO environment
HP VLS systems with Accelerated deduplication specifically designed for the high
performance and high capacity requirements of the enterprise
Low bandwidth replication support on D2D & VLS with large fan-in ratio support – changing
the dynamics and costs of “off-site” data protection
HP Physical Tape Systems (MSL, EML, ESL) for the ultimate safe repository of data.
Single point of control from the main data centre using HP data protector management and
scheduling tools.
Using the wide range of components above allows flexibility and scalability in the variety of ROBO
and data centre backup solutions that can be constructed. With innovative technologies such as
synthetic full functionality, deduplication and low bandwidth replication on VTL products HP is able to
deliver the optimum solution, with optimum performance at the best cost for each specific location,
whilst ensuring central management and control.

Glossary of Terms
HP StorageWorks Sizer Tool
This freely available tool http://www.hp.com/go/storageworks/sizer allows users to specify backup
capacities, retention schemes, data change rates, replication window, link speed etc and calculates
likely backup storage capacity required, VTL model required, deduplication ratios, time to replicate (
if link speed specified), link bandwidth required ( if replication window specified). The tool then
provides a design summary and a priced parts list ( list price).
HP D2D
This is HPs virtual tape library designed specifically for ROBO and Small/Medium enterprise, it scales
in capacity from 1.5TB user to 18 TB user and uses HP Dynamic Deduplication technology which then
enables Low Bandwidth replication. Available with iSCSI Fiber Channel and NAS* interfaces and has
inbuilt physical tape offload functionality. See Appendix A * Available Late 2009
HP VLS
This is HPs virtual tape library designed specifically for the Enterprise it scales in capacity from 7.5 TB
to 1280 TB user and uses HP Accelerated Deduplication technology which then enables Low
Bandwidth replication. A multi-node architecture enables highly scalable performance.
See Appendix A
HP Data Protector software
HP Data Protector software automates high-performance backup and recovery from disk or tape to
enable 24x7 business continuity at a compelling price-to-performance ratio. Appropriate for medium
and large companies, this software helps you reduce IT costs and complexity while delivering the
reliability and scalability needed to grow from a single server environment to the largest distributed
enterprise infrastructure. With more than 22,000 customers worldwide, HP Data Protector software is
used by nearly half of Global 500 corporations.
Target-based Deduplication
This is where the data is deduplicated in a Target device such as a virtual tape library. Deduplication
is the ability to detect identical data patterns and save them only once – hence saving on overall
storage requirements.
Active->Passive
Replication from a Source to Destination in one direction only.
Active-Active
Replication from a Source device on Site A to a Target Device on Site B and vice versa.
Many-to-One
Replication from multiple sources to a single target device.
Deduplication ratio
The reduction in storage required for a backup (after several other backups have taken place). The
ratio is highly dependent on:
Rate of change of data (for example, 10% of the data in 10% of the files)
Type of data—files vs database
Retention period of backups
Efficiency of deduplication technology implementation

In-Line ( HP Dynamic deduplication)
This is where the deduplication process takes place REAL TIME as the backup is actually taking place.
This is the technology used on HP D2D devices.
Post Process ( HP Accelerated Deduplication)
This is where the deduplication process takes place AFTER the backup has landed on the device to
ensure deduplication does not affect backup performance. This is the technology used on HP VLS
devices
Source Library
When used as part of a replication pair the source library is the library supplying the data to be
replicated.
Target Library
When used as part of a replication pair the target library is the library receiving the data from the
source library.
Concurrency
This is the Number of replication jobs that can be active at any one time— this varies depending on if
it is a source or target library. Concurrency ensures maximum use of the available link bandwidth.
Fan-In
This is the number of source appliances or libraries that can channeled into a target appliance
or library.
Link Speed
This is speed in Mbits/sec that the Telco provides point to point or Any to Any to allow replication to
take place. The speeds can vary from 2 Mb/sec to 1 Gb/sec. Increasing Speed means increasing
cost.
Bandwidth Utilization (Throttling)
This is the amount of available bandwidth a device can be configured to use. For example the D2D
& VLS devices have network throttling so they can be configured to use for example only 20% of the
available bandwidth. This prevents any single device from “hogging” the total bandwidth available,
and allows replication to take place over longer periods of time without affecting application
responses using the same link.
Synthetic full
Synthetic backup puts a stop to the buildup of incremental backups, and eliminates the need to run
lengthy full backups. This technology works by merging all incremental backups into a full ‘synthetic’
backup—a process that can be repeated indefinitely, with no need to run a full backup again. If all
the backups, full and incremental, are written to the same HP Data Protector file library which uses a
distributed file media format (DFMF) e.g on an MSA2000 disk array, an even more efficient type of
synthetic backup is possible. This is called Virtual Full Backup. The solution uses pointers to
consolidate data rather than copying the data. Asa result, the consolidation takes less time and
avoids unnecessary duplication of data. This capability also helps enable continuous data protection
for Windows systems. For systems running Windows 2000 and above, HP Data Protector utilizes the
built-in Microsoft Windows Change Journal to quickly generate a list of files that have been altered
since the last backup was performed. This option avoids the need for timely “tree walks” to identify
files that have changed, which can be especially time-consuming on systems with many small files.
This allows incremental backups to run much faster and more frequently, providing near-continuous
data protection at no additional cost.

HP Data Protector Cell Manager
The Cell Manager is the main system in the cell. The Cell Manager:
• Manages the cell from a central point
• Contains the IDB ( Internal Data Base)
The IDB contains information about backup details such as, backup durations, media IDs, and session
IDs
• Runs core HP Data Protector software
• Runs Session Managers that start and stop backup and restore sessions and write session
information to the IDB.
HP Data Protector Disk Agents
Client systems you want to back up must have the HP Data Protector Disk Agent (DA), also called
Backup Agent, installed. To back up online database integrations, install the Application Agent. The
Disk Agent reads or writes data from a disk on the system and sends or receives data from a Media
Agent. The Disk Agent is also installed on the Cell Manager, thus allowing you to back up data on
the Cell Manager, the HP Data Protector configuration, and the IDB.
HP Data Protector Media Server
Client systems with connected backup devices must have a HP Data Protector Media Agent (MA)
installed. Such client systems are also called Drive Servers. A backup device can be connected to any
system and not only to the Cell Manager. A Media Agent reads or writes data from or to media in the
device and sends or receives data from the Disk Agent.
HP Data Protector Object Copy
The Data Protector object copy functionality enables you to copy selected object versions to a specific
media set. You can select object versions from one or several backup sessions or object consolidation
sessions. During the object copy session, Data Protector reads the backed up data from the source
media, transfers the data, and writes it to the target media.
The result of an object copy session is a media set that contains copies of the object versions you
specified.
Tape Import scripts
The replication in both the VLS and D2D systems is mirroring the source cartridge to its matching
target cartridge so both cartridges have the same barcode, the same tape contents, etc. HP Data
Protector currently cannot handle seeing two copies of the same cartridge at the same time (because
to the backup application, the cartridge is a single entity in the media management database). With
HP Data Protector you can use a second cell manager to import and manage the replicated
media/data.
Since replication will result in source and target media having identical barcodes, the source and
target device should not be visible in one cell. SAN zoning is a method to assign portions of a virtual
library to different backup applications such as HP Data Protector.
For VLS systems, the replication target is a subset or an entire virtual library that is presented on front-
end Fibre Channel ports. This library is available in read only mode which allows replicated data to
be managed using a second HP Data Protector cell manager. The VLS provides email notification
reporting on completion of replication jobs.
For D2D systems, the replication target is an entire D2D library that is presented to a second HP Data
Protector cell manager. The D2D provides XML polling notification reporting on completion of
replication jobs.

A front-end script will handle the “notification” and feed a “incoming” queue. This frontend is
depended on the device (VLS – email processing, D2D XML polling).
The backend processes the incoming queue and distributes the media to import to the available
devices. The backend will maintain a log of import jobs and re-queue jobs in case of failures.
Replication Window
A configurable period of time within the D2D & VLS systems during which replication is not allowed
to take place. Primarily this is to ensure available WAN bandwidth is not oversubscribed during peak
periods of demand which might slow down application performance.
Seeding/Initializing
This term is used to define the process of “synchronizing” the two D2D or VLS appliances with the
correct data prior to low bandwidth replication commencing. Because low bandwidth replication only
transfers differences the Virtual tape libraries have to have the baseline/reference data established
before low bandwidth replication can work.
Importing/Exporting
For Seeding large quantities of data we cannot use a low bandwidth link, so physical tape or co-
location is used to allow the source and target devices to be synchronized. If physical tape is used an
export and import process is used to get data out of and back into the D2D or VLS devices.
Tape Offload
On D2D devices there is an in-built tape offload utility accessible from the user interface that allows
scheduled copies of the replicated data onto physical tape device connected directly to the D2D by
SCSI or SAS host bus adapter inside the D2D.

Appendix A – HP VTL Family with Deduplication and Low
Bandwidth replication
Figure 5: HP Virtual Tape Library portfolio with Deduplication and Low Bandwidth replication
The above figure shows the complete range of HP Virtual Tape Solutions. The D2D2500 is best suited
for the most remote offices, the D2D4112 offers major benefits in consolidation by being able to
support up to 24 remote D2D2500’s. The VLS systems are highly scalable in terms of capacity
( 7.5 TB to 1280TB) and performance ( 400MB/sec to 4800MB/sec) and currently support 4 to 1
fan-in. NAS emulation on D2D units to support synthetic full backups will be available Late 2009.

Appendix B – HP Data Protector Synthetic Full Backup
Figure 6: HP Data Protector Synthetic full backup explained

Figure 7: HP Data Protector Synthetic full backup explained
HP Data Protector software offers an advanced backup solution called synthetic full backup. This
solution enables you to create synthetic full backups and virtual full backups with an operation called
object consolidation allowing implementing an incremental forever backup strategy.
The incremental forever paradigm means that except for the first backup where a full backup is
performed, only incremental backups are executed. This concept presents the most efficient way of
backups; only the changed data is backed up.
However, without object consolidation, the restore process would last far too long since all backup
sessions would have to be restored. Due to this behavior, regular full backups are required and all
backups would need to be protected permanently. Object consolidation removes this drawback.
During the object consolidation session, HP Data Protector software reads the backed up data from
the source media, merges the data, and writes the consolidated version to the target media.
An object consolidation can result either in a synthetic full or a virtual full backup.
A synthetic full backup is the result of an object consolidation operation where a restore chain of
backup objects is merged into a new, synthetic full version of this object. A synthetic full backup is
equivalent to a conventional full backup in terms of restore speed. HP D2D NAS emulation supports
synthetic full backups
A virtual full backup is an efficient type of synthetic backup where data is consolidated using pointers
instead of being copied. It is performed if all the backups (the full backup, incremental backups, and
the resulting virtual full backup) are written to a single HP Data Protector software file library using
distributed file media format. This requires the File Library to be a disk array such as HP MSA2000