HP J9311A User manual

HP 3500-24G-PoE yl Switch HP 3500-48G-PoE yl Switch
Models
HP 3500-48G-PoE+ yl Switch J9311A
HP 3500-24G-PoE+ yl Switch J9310A
HP 3500-48G-PoE yl Switch J8693A
HP 3500-24G-PoE yl Switch J8692A
HP 3500-48-PoE Switch J9473A
HP 3500-24-PoE Switch J9471A
HP 3500-48 Switch J9472A
HP 3500-24 Switch J9470A
Key features
Advanced access layer and small distribution
Enterprise-class performance and security
Intelligent edge feature set with L2 to L4 support
Scalable 10/100/1000 PoE+ and 10/100 PoE
Unified core-to-edge HP ProVision software
Product overview
The HP 3500 Switch Series consists of advanced intelligent-edge switches, available in 24-port and 48-port fixed-port models. The
foundation for these switches is a purpose-built, programmable HP ProVision ASIC that allows the most demanding networking
features, such as quality of service (QoS) and security, to be implemented in a scalable yet granular fashion. With a variety of Gigabit
Ethernet and 10/100 interfaces; integrated PoE+, PoE, and non-PoE options; and versatile 10GbE connectivity (CX4, X2, and SFP+) on
Gigabit Ethernet switches, the 3500 Switch Series offers excellent investment protection, flexibility, and scalability, as well as ease of
deployment, operation, and maintenance.
Features and Benefits
Software-defined networking
NEW OpenFlow
supports OpenFlow 1.0 and 1.3 specifications to enable SDN by allowing separation of the data (packet forwarding) and control
(routing decision) paths
Quality of Service (QoS)
Advanced classifier-based QoS
classifies traffic using multiple match criteria based on Layer 2, 3, and 4 information; applies QoS policies such as setting priority
level and rate limit to selected traffic on a per-port or per-VLAN basis
QuickSpecs
HP 3500 and 3500 yl Switch Series
Overview
DA - 13282 Worldwide — Version 19 — December 9, 2013 Page 1

Layer 4 prioritization
enables prioritization based on TCP/UDP port numbers
Traffic prioritization
allows real-time traffic classification into eight priority levels mapped to eight queues
Bandwidth shaping
Port-based rate limiting
provides per-port ingress-/egress-enforced increased bandwidth
Classifier-based rate limiting
uses an access control list (ACL) to enforce increased bandwidth for ingress traffic on each port
Reduced bandwidth
provides per-port, per-queue egress-based reduced bandwidth
Class of Service (CoS)
sets the IEEE 802.1p priority tag based on IP address, IP Type of Service (ToS), Layer 3 protocol, TCP/UDP port number, source
port, and DiffServ
Management
Remote intelligent mirroring
mirrors selected ingress/egress traffic based on ACL, port, MAC address, or VLAN to a local or remote HP 8200 zl, 6600, 6200 yl,
5400 zl, or 3500 Switch anywhere on the network
RMON, XRMON, and sFlow v5
provide advanced monitoring and reporting capabilities for statistics, history, alarms, and events
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
advertises and receives management information from adjacent devices on a network, facilitating easy mapping by network
management applications
Uni-Directional Link Detection (UDLD)
monitors a cable between two switches and shuts down the ports on both ends if the cable is broken, turning the bidirectional
link into a unidirectional one; this prevents network problems such as loops
Management simplicity
common software features and CLI implementation across all ProVision-based switches (including the zl and yl switches)
Command authorization
leverages RADIUS to link a custom list of CLI commands to an individual network administrator's login; an audit trail documents
activity
Friendly port names
allow assignment of descriptive names to ports
Dual flash images
provide independent primary and secondary operating system files for backup while upgrading
Multiple configuration files
stores easily to the flash image
Comware CLI
Comware-compatible CLI
bridges the experience of HP Comware CLI users who are using the HP ProVision software CLI
Display and fundamental Comware CLI commands
are embedded in the switch CLI as native commands; display output is formatted as on Comware-based switches, and
fundamental commands provide a Comware-familiar initial switch setup
Configuration Comware CLI commands
when Comware commands are entered, CLI help is elicited to formulate the correct ProVision software CLI comman
Connectivity
QuickSpecs
HP 3500 and 3500 yl Switch Series
Overview
DA - 13282 Worldwide — Version 19 — December 9, 2013 Page 2

IEEE 802.3af Power over Ethernet (PoE)
provides up to 15.4 W per port to IEEE 802.3af-compliant PoE-powered devices such as IP phones, wireless access points, and
security cameras
IEEE 802.3at Power over Ethernet Plus (PoE+)
provides up to 30 W per port to IEEE 802.3 for devices that use PoE/PoE+, such as video IP phones, IEEE 802.11n wireless access
points, and advanced pan/zoom/tilt security cameras
Prestandard PoE support
detects and provides power to prestandard PoE devices; see list of supported devices in the product FAQs at
www.hp.com/networking
Jumbo frames
on Gigabit Ethernet and 10-Gigabit Ethernet ports, jumbo frames allow high-performance remote backup and disaster-recovery
services
Auto-MDIX
provides automatic adjustments for straight-through or crossover cables on all 10/100 and 10/100/1000 ports
IPv6
IPv6 host
enables switches to be managed in an IPv6 network
Dual stack (IPv4 and IPv6)
transitions from IPv4 to IPv6, supporting connectivity for both protocols
MLD snooping
forwards IPv6 multicast traffic to the appropriate interface
IPv6 ACL/QoS
supports ACL and QoS for IPv6 network traffic
IPv6 routing
supports static and OSPFv3 routing protocols
6in4 tunneling
supports encapsulation of IPv6 traffic in IPv4 packets
Performance
High-speed/capacity architecture
up to 153.6 Gbps crossbar switching fabric provides intra- and inter-module switching with up to 111.5 million pps throughput
on the purpose-built ProVision ASICs
Selectable queue configurations
allows for increased performance by selecting the number of queues and associated memory buffering that best meet the
requirements of the network applications
Resiliency and high availability
NEW Virtual Router Redundancy Protocol (requires Premium License)
allows groups of two routers to dynamically back each other up to create highly available routed environments
IEEE 802.1s multiple Spanning Tree Protocols
provides high link availability in multiple VLAN environments by allowing multiple spanning trees; encompasses IEEE 802.1D
Spanning Tree Protocol and IEEE 802.1w Rapid Spanning Tree Protocol
IEEE 802.3ad Link Aggregation Control Protocol (LACP) and HP port trunking
support up to 144 trunks, each with up to eight links (ports) per trunk
Distributed trunking
enables loop-free and redundant network topology without using Spanning Tree Protocol; allows a server or switch to connect
to two switches using one logical trunk for redundancy and load sharing
Uplink Failure Detection
QuickSpecs
HP 3500 and 3500 yl Switch Series
Overview
DA - 13282 Worldwide — Version 19 — December 9, 2013 Page 3

provides active-standby network path redundancy for servers that are configured for active-standby NIC teaming
NEW SmartLink
provides easy-to-configure link redundancy of active and standby link
Layer 2 switching
IEEE 802.1ad Q-in-Q (requires Premium License)
increases the scalability of an Ethernet network by providing a hierarchical structure; connects multiple LANs on a high-speed
campus or metro network
HP switch meshing
dynamically load balances across multiple active redundant links to increase available aggregate bandwidth
VLAN support and tagging
supports the IEEE 802.1Q standard and 2,048 VLANs simultaneously
IEEE 802.1v protocol VLANs
isolate select non-IPv4 protocols automatically into their own VLANs
GARP VLAN Registration Protocol
allows automatic learning and dynamic assignment of VLANs
Rapid Per-VLAN Spanning Tree (RPVST+)
allows each VLAN to build a separate spanning tree to improve link bandwidth usage; is compatible with PVST+
Layer 3 services
User Datagram Protocol (UDP) helper function
allows UDP broadcasts to be directed across router interfaces to specific IP unicast or subnet broadcast addresses and prevents
server spoofing for UDP services such as DHCP
Loopback interface address
defines an address in Routing Information Protocol (RIP) and Open Standard Path First (OSPF), improving diagnostic capability
Route maps
provide more control during route redistribution; allow filtering and altering of route metrics
Layer 3 routing
Static IP routing
provides manually configured routing for both IPv4 and IPv6 networks
Routing Information Protocol (RIP)
provides RIPv1 and RIPv2 routing
OSPF (requires Premium License)
provides OSPFv2 for IPv4 routing and OSPFv3 for IPv6 routing
Border Gateway Routing Protocol (requires Premium License)
provides IPv4 Border Gateway Routing Protocol that is scalable, robust, and flexible
Security
Access control lists (ACLs)
provide filtering based on the IP field, source/destination IP address/subnet, and source/destination TCP/UDP port number on a
per-VLAN or per-port basis
Multiple user authentication methods
IEEE 802.1X users per port
provides authentication of multiple IEEE 802.1X users per port
Web-based authentication
authenticates from Web browser for clients that do not support IEEE 802.1X supplicant
QuickSpecs
HP 3500 and 3500 yl Switch Series
Overview
DA - 13282 Worldwide — Version 19 — December 9, 2013 Page 4

MAC-based authentication
client is authenticated with the RADIUS server based on client's MAC authentication
Concurrent IEEE 802.1X, Web, and MAC authentication schemes per port
switch port accepts up to 32 sessions of IEEE 802.1X, Web, and MAC authentications
Virus throttling
detects traffic patterns typical of worm-type viruses and either throttles or entirely prevents the virus from spreading across the
routed VLANs or bridged interfaces without requiring external appliances
DHCP protection
blocks DHCP packets from unauthorized DHCP servers, preventing denial-of-service attacks
Secure management access
delivers secure encryption of all access methods (CLI, GUI, or MIB) through SSHv2, SSL, and/or SNMPv3
USB Secure Autorun (requires HP PCM+)
deploys, diagnoses, and updates a switch using a USB flash drive; works with a secure credential to prevent tampering
Switch CPU protection
provides automatic protection against malicious network traffic trying to shut down the switch
ICMP throttling
defeats ICMP denial-of-service attacks by enabling any switch port to automatically throttle ICMP traffic
Identity-driven ACL
enables implementation of a highly granular and flexible access security policy and VLAN assignment specific to each
authenticated network user
STP BPDU port protection
blocks Bridge Protocol Data Units (BPDUs) on ports that do not require BPDUs, preventing forged BPDU attacks
Dynamic IP lockdown
works with DHCP protection to block traffic from unauthorized hosts, preventing IP source address spoofing
Dynamic ARP protection
blocks ARP broadcasts from unauthorized hosts, preventing eavesdropping or theft of network data
STP Root Guard
protects the root bridge from malicious attacks or configuration mistakes
Detection of malicious attacks
monitors 10 types of network traffic and sends a warning when an anomaly that potentially can be caused by malicious attacks
is detected
Port security
allows access only to specified MAC addresses, which can be learned or specified by the administrator
MAC address lockout
prevents particular configured MAC addresses from connecting to the network
Source-port filtering
allows only specified ports to communicate with each other
RADIUS/TACACS+
eases switch management security administration by using a password authentication server
Secure Shell
encrypts all transmitted data for secure remote CLI access over IP networks
Secure Sockets Layer (SSL)
encrypts all HTTP traffic, allowing secure access to the browser-based management GUI in the switch
Secure FTP
allows secure file transfer to and from the switch; protects against unwanted file downloads or unauthorized copying of a switch
configuration file
Management Interface Wizard
helps secure management interfaces such as SNMP, telnet, SSH, SSL, Web, and USB at the desired level
Switch management logon security
helps secure switch CLI logon by optionally requiring either RADIUS or TACACS+ authentication
QuickSpecs
HP 3500 and 3500 yl Switch Series
Overview
DA - 13282 Worldwide — Version 19 — December 9, 2013 Page 5

Security banner
displays a customized security policy when users log in to the switch
Convergence
IP multicast routing (requires Premium License)
includes PIM Sparse and Dense modes to route IP multicast traffic
IP multicast snooping (data-driven IGMP)
prevents flooding of IP multicast traf
LLDP-MED (Media Endpoint Discovery)
defines a standard extension of LLDP that stores values for parameters such as QoS and VLAN to automatically configure
network devices such as IP phones
PoE allocations
support multiple methods (automatic, IEEE 802.3af class, LLDP-MED, or user specified) to allocate PoE power for more efficient
energy savings
Auto VLAN configuration for voice
RADIUS VLAN
uses a standard RADIUS attribute and LLDP-MED to automatically configure a VLAN for IP phones
CDPv2
uses CDPv2 to configure legacy IP phones
NEW Local MAC Authentication
assigns attributes such as VLAN and QoS using locally configured profile that can be a list of MAC prefixes
Warranty and support
Lifetime Warranty 2.0
advance hardware replacement for as long as you own the product with next-business-day delivery (available in most countries)†
Electronic and telephone support (for Lifetime Warranty 2.0)
limited 24x7 telephone support is available from HP for the first 3 years; limited electronic and business hours telephone
support is available from HP for the entire warranty period; to reach our support centers, refer to
www.hp.com/networking/contact-support ; for details on the duration of support provided with your product purchase, refer
to www.hp.com/networking/warrantysummary
Software releases
to find software for your product, refer to www.hp.com/networking/support ; for details on the software
releases available with your product purchase, refer to www.hp.com/networking/warrantysummary
†HP warranty includes repair or replacement of hardware for as long as you own the product, with next business day advance
replacement (available in most countries). The disk drive included with HP AllianceOne Advanced Services and Services zl Modules, HP
Threat Management Services zl Module, HP AllianceOne Extended zl Module with Riverbed Steelhead, HP MSM765zl Mobility Controller
and HP Survivable Branch Communication zl Module powered by Microsoft Lync has a five-year hardware warranty. For details, refer to
the Software license and hardware warranty statements at: www.hp.com/networking/warranty .
QuickSpecs
HP 3500 and 3500 yl Switch Series
Overview
DA - 13282 Worldwide — Version 19 — December 9, 2013 Page 6

Build To Order:
BTO is a standalone unit with no integration. BTO products ship standalone are not part of a CTO or Rack-Shippable solution.
HP 3500-24 Switch J9470A
20 autosensing 10/100/1000 port
4 dual-personality ports
min=0 \ max=4 SFP Transceivers
1U - Height
See Configuration Note:1,
2
PDU Cable NA/MEX/TW/JP J9470A#B2B
C15 PDU Jumper Cord (NA/MEX/TW/JP)
PDU Cable ROW J9470A#B2C
C15 PDU Jumper Cord (ROW)
HP 3500-24-PoE Switch J9471A
20 autosensing 10/100/1000 port
4 dual-personality ports
min=0 \ max=4 SFP Transceivers
1U - Height
See Configuration Note:1,
2
PDU Cable NA/MEX/TW/JP J9471A#B2B
C15 PDU Jumper Cord (NA/MEX/TW/JP)
PDU Cable ROW J9471A#B2C
C15 PDU Jumper Cord (ROW)
HP 3500-24G-PoE Yl Switch J8692A
20 autosensing 10/100/1000 port
4 dual-personality ports
min=0 \ max=4 SFP Transceivers
1 open module slot
1U - Height
See Configuration Note:1,
2
PDU Cable NA/MEX/TW/JP J8692A#B2B
C15 PDU Jumper Cord (NA/MEX/TW/JP)
PDU Cable ROW J8692A#B2C
C15 PDU Jumper Cord (ROW)
HP 3500-24G-PoE+ yl Switch J9310A
20 autosensing 10/100/1000 port
4 dual-personality ports
min=0 \ max=4 SFP Transceivers
1 open module slot
1U - Height
See Configuration Note:1,
2
QuickSpecs
HP 3500 and 3500 yl Switch Series
Configuration
DA - 13282 Worldwide — Version 19 — December 9, 2013 Page 7

PDU Cable NA/MEX/TW/JP J9310A#B2B
C15 PDU Jumper Cord (NA/MEX/TW/JP)
PDU Cable ROW J9310A#B2C
C15 PDU Jumper Cord (ROW)
HP 3500-48 Switch J9472A
44 autosensing 10/100/1000 port
4 dual-personality ports
min=0 \ max=4 SFP Transceivers
1U - Height
See Configuration Note:1,
2
PDU Cable NA/MEX/TW/JP J9472A#B2B
C15 PDU Jumper Cord (NA/MEX/TW/JP)
PDU Cable ROW J9472A#B2C
C15 PDU Jumper Cord (ROW)
HP 3500-48-PoE Switch J9473A
44 autosensing 10/100/1000 port
4 dual-personality ports
min=0 \ max=4 SFP Transceivers
1U - Height
See Configuration Note:1,
2
PDU Cable NA/MEX/TW/JP J9473A#B2B
C15 PDU Jumper Cord (NA/MEX/TW/JP)
PDU Cable ROW J9473A#B2C
C15 PDU Jumper Cord (ROW)
HP 3500-48G-PoE yl Switch J8693A
44 autosensing 10/100/1000 port
4 dual-personality ports
min=0 \ max=4 SFP Transceivers
1 open module slot
1U - Height
See Configuration Note:1,
2
PDU Cable NA/MEX/TW/JP J8693A#B2B
C15 PDU Jumper Cord (NA/MEX/TW/JP)
PDU Cable ROW J8693A#B2C
C15 PDU Jumper Cord (ROW)
HP 3500-48G-PoE+ yl Switch J9311A
QuickSpecs
HP 3500 and 3500 yl Switch Series
Configuration
DA - 13282 Worldwide — Version 19 — December 9, 2013 Page 8

44 autosensing 10/100/1000 port
4 dual-personality ports
min=0 \ max=4 SFP Transceivers
1 open module slot
1U - Height
See Configuration Note:1,
2
PDU Cable NA/MEX/TW/JP J9311A#B2B
C15 PDU Jumper Cord (NA/MEX/TW/JP)
PDU Cable ROW J9311A#B2C
C15 PDU Jumper Cord (ROW)
Configuration Rules:
Note 1 The following Transceivers install into this Switch:
HP X111 100M SFP LC FX Transceiver J9054C
HP X112 100M SFP LC BX-D Transceiver J9099B
HP X112 100M SFP LC BX-U Transceiver J9100B
HP X121 1G SFP LC LH Transceiver J4860C
HP X121 1G SFP LC LX Transceiver J4859C
HP X121 1G SFP LC SX Transceiver J4858C
HP X122 1G SFP LC BX-D Transceiver J9142B
HP X122 1G SFP LC BX-U Transceiver J9143B
Note 2 Localization required on orders without #B2B or #B2C options.
Remarks:
Drop down under power supply should offer the following options and results:
Switch/Router/Power Supply to PDU Power Cord - #B2B in North America, Mexico, Taiwan, and Japan or #B2C
ROW. (Watson Default B2B or B2C for Rack Level CTO)
Switch/Router/Power Supply to Wall Power Cord - Localized Option (Watson Default for BTO and Box Level
CTO)
Factory Racked Models
HP 3500-48G-PoE+ yl Switch J9311A
44 autosensing 10/100/1000 port
4 dual-personality ports
min=0 \ max=4 SFP Transceivers
1 open module slot
1U - Height
See Configuration Note:1,
2
PDU Cable NA/MEX/TW/JP J9311A#B2B
C15 PDU Jumper Cord (NA/MEX/TW/JP)
PDU Cable ROW J9311A#B2C
QuickSpecs
HP 3500 and 3500 yl Switch Series
Configuration
DA - 13282 Worldwide — Version 19 — December 9, 2013 Page 9

C15 PDU Jumper Cord (ROW)
HP 3500-24G-PoE+ yl Switch J9310A
20 autosensing 10/100/1000 port
4 dual-personality ports
min=0 \ max=4 SFP Transceivers
1 open module slot
1U - Height
See Configuration Note:1,
2
PDU Cable NA/MEX/TW/JP J9310A#B2B
C15 PDU Jumper Cord (NA/MEX/TW/JP)
PDU Cable ROW J9310A#B2C
C15 PDU Jumper Cord (ROW)
HP 3500-48G-PoE yl Switch J8693A
44 autosensing 10/100/1000 port
4 dual-personality ports
min=0 \ max=4 SFP Transceivers
1 open module slot
1U - Height
See Configuration Note:1,
2
PDU Cable NA/MEX/TW/JP J8693A#B2B
C15 PDU Jumper Cord (NA/MEX/TW/JP)
PDU Cable ROW J8693A#B2C
C15 PDU Jumper Cord (ROW)
HP 3500-24G-PoE Yl Switch J8692A
20 autosensing 10/100/1000 port
4 dual-personality ports
min=0 \ max=4 SFP Transceivers
1 open module slot
1U - Height
See Configuration Note:1,
2
PDU Cable NA/MEX/TW/JP J8692A#B2B
C15 PDU Jumper Cord (NA/MEX/TW/JP)
PDU Cable ROW J8692A#B2C
C15 PDU Jumper Cord (ROW)
HP 3500-48-PoE Switch J9473A
44 autosensing 10/100/1000 port
4 dual-personality ports
min=0 \ max=4 SFP Transceivers
1U - Height
See Configuration Note:1,
2
QuickSpecs
HP 3500 and 3500 yl Switch Series
Configuration
DA - 13282 Worldwide — Version 19 — December 9, 2013 Page 10