HP JC106A User manual

Models
HP 5820-14XG-SFP+ Switch with 2 Slots JC106A
HP 5820X-24XG-SFP+ Switch JC102A
HP 5820AF-24XG Switch JG219A
Key features
For enterprise edge, or distribution/data center
Up to 24 ports of 10GbE per unit/194 per stack
Flex chassis—modular resiliency
Cut-through switching for very low latency
Hot-swappable I/O, power supplies, and fans
Product overview
The HP 5820 Switch Series supports advanced features that deliver a unique combination of unmatched 10 Gigabit Ethernet; Fibre
Channel over Ethernet (FCoE) connectivity; high-availability architecture; full Layer 2/3 dual-stack IPv4/IPv6; and line-rate, low-latency
performance on all ports. Extensible embedded application capabilities enable these switches to integrate services into the network,
consolidating devices and appliances to simplify deployment and reduce power consumption and rack space. Extremely versatile, the
switches can be used in high-performance, high-density building or department cores as part of a consolidated network; for data
center top-of-rack server access; or as high-performance Layer 3, 10GbE aggregation switches in campus and data center networks.
Features and benefits
Quality of Service (QoS)
Powerful QoS feature
creates traffic classes based on access control lists (ACLs), IEEE 802.1p precedence, IP, and DSCP or Type of Service (ToS)
precedence; supports filter, redirect, mirror, or remark; supports the following congestion actions: strict priority (SP) queuing,
weighted round robin (WRR), weighted fair queuing (WFQ), weighted random early discard (WRED), weighted deficit round robin
(WDRR), and SP+WDRR
Integrated network services
with support for open application architecture (OAA) modules, extends and integrates application capability into the network
Ring Resiliency Protection Protocol (RRPP)
provides fast recovery for ring Ethernet-based topology; helps ensure consistent application performance for applications such
as VoIP
Management
Remote configuration and management
is available through a secure Web browser or a command-line interface (CLI)
IEEE 802.1ab LLDP discovery
advertises and receives management information from adjacent devices on a network
USB support
File copy
allows users to copy switch files to and from a USB flash drive
DHCP options
QuickSpecs
HP 5820 Switch Series
Overview
DA - 13791 North America — Version 18 — November 22, 2013 Page 1

provides server (RFC 2131), client, snooping, and relay options
SNMPv1, v2c, and v3
facilitate centralized discovery, monitoring, and secure management of networking devices
sFlow
provides scalable ASIC-based network monitoring and accounting; this allows network operators to gather a variety of
sophisticated network statistics and information for capacity planning and real-time network monitoring purposes
Network Time Protocol (NTP)
synchronizes timekeeping among distributed time servers and clients; keeps consistent timekeeping among all clock-dependent
devices within the network so that the devices can provide diverse applications based on the consistent time
Connectivity
High-density port connectivity
194 10-GbE ports with a 40 Gbps resilient backplane
Data center I/O consolidation
the 5820-14XG FCoE module supports two 4x8/4/2 Gbps FCoE modules (up to eight FC ports total) to reduce cost and
complexity while boosting network performance
Auto-MDIX
provides automatic adjustments for straight-through or crossover cables on all 10/100 and 10/100/1000 ports
Jumbo frames
on Gigabit Ethernet and 10-Gigabit ports, jumbo frames allow high-performance remote backup and disaster-recovery services
IPv6 native support
IPv6 host
enables switches to be managed and deployed at the IPv6 network's edge
Dual stack (IPv4/IPv6)
transitions from IPv4 to IPv6, supporting connectivity for both protocols
MLD snooping
forwards IPv6 multicast traffic to the appropriate interface
IPv6 ACL/QoS
supports ACL and QoS for IPv6 network traffic, preventing traffic flooding
IPv6 routing
supports IPv6 static routes and IPv6 versions of RIP, OSPF, IS-IS, and Border Gateway Protocol (BGP) routing protocols
Performance
Hardware-based wire-speed access control lists (ACLs)
helps provide high levels of security and ease of administration without impacting network performance with a feature-rich
TCAM-based ACL implementation
Unique versatile architecture
supports the best of both fixed-port and modular configurations
Cut-through switching
delivers wire-speed, line-rate performance on all ports, as well as cut-through switching for low latency
Resiliency and high availability
Data center–optimized design
HP 5820AF-24XG Switch (JG219A) supports front-to-back/back-to-front airflow for hot/cold aisles, rear rack mounts, and
redundant hot-swappable AC or DC power and fans
Manageability
QuickSpecs
HP 5820 Switch Series
Overview
DA - 13791 North America — Version 18 — November 22, 2013 Page 2

Full-featured console
provides complete control of the switch with a familiar CLI
Web interface
allows configuration of the switch from any Web browser on the network
RMON and sFlow
provide advanced monitoring and reporting capabilities for statistics, history, alarms, and events
Multiple configuration files
allow multiple configuration files to be stored to a flash image
Troubleshooting
Ingress and egress port monitoring
enable network problem solving
Traceroute and ping
enable testing of network connectivity
Virtual cable tests
provide visibility to cable problems
Layer 2 switching
32K MAC addresses
provide access to many Layer 2 devices
4,094 port-based VLANs
provide security between workgroups
IEEE 802.1ad QinQ and Selective QinQ
increase the scalability of an Ethernet network by providing a hierarchical structure; connect multiple LANs on a high-speed
campus or metro network
Gigabit Ethernet port aggregation
allows grouping of ports to increase overall data throughput to a remote device
10 GbE port aggregation
allows grouping of ports to increase overall data throughput to a remote device
Spanning Tree/MSTP, RSTP, and STP Root Guard
prevent network loops
sFlow
allows traffic sampling
GVRP VLAN Registration Protocol
allows automatic learning and dynamic assignment of VLANs
Layer 3 services
Address Resolution Protocol (ARP)
determines the MAC address of another IP host in the same subnet; supports static ARPs; gratuitous ARP allows detection of
duplicate IP addresses; proxy ARP allows normal ARP operation between subnets or when subnets are separated by a Layer 2
network
Dynamic Host Configuration Protocol (DHCP)
simplifies the management of large IP networks and supports client and server; DHCP Relay enables DHCP operation across
subnets
Layer 3 routing
Layer 3 IPv4 routing
provides routing of IPv4 at media speed; supports static routes, RIP and RIPv2, OSPF, IS-IS, and BGP
QuickSpecs
HP 5820 Switch Series
Overview
DA - 13791 North America — Version 18 — November 22, 2013 Page 3

Routing Information Protocol (RIP) and RIPng support
provides complete support of RIP for both IPv4 and IPv6
OSPF and OSPFv3 support
provides complete support of OSPF for both IPv4 and IPv6
IS-IS and IS-ISv6 support
provides complete support of IS-IS for both IPv4 and IPv6
Layer 3 IPv6 routing
provides routing of IPv6 at media speed; supports static routes, RIPng, OSPFv3, IS-ISv6, and BGP4+
Bidirectional Forwarding Detection (BFD)
enables link connectivity monitoring and reduces network convergence time for RIP, OSPF, BGP, IS-IS, VRRP, MPLS, and IRF
Virtual Router Redundancy Protocol (VRRP) and VRRP Extended
allow quick failover of router ports
Policy-based routing
makes routing decisions based on policies set by the network administrator
IGMPv1, v2, and v3
allow individual hosts to be registered on a particular VLAN
PIM-SSM, PIM-DM, and PIM-SM (for IPv4 and IPv6)
support IP Multicast address management and inhibition of DoS attacks
Equal-Cost Multipath (ECMP)
enables multiple equal-cost links in a routing environment to increase link redundancy and scale bandwidth
Security
Defense-in-depth security
provides integrated and distributed security enforcement that can be managed from a central location, such as the HP Intelligent
Management Center (IMC)
Advanced processor queuing mechanism
helps prevent denial-of-service (DoS) attacks, while DHCP snooping helps ensure that devices can only receive an IP address
from a legitimate DHCP server on the network
RADIUS/HWTACACS
eases switch management security administration by using a password authentication server
Secure Shell (SSHv2)
encrypts all transmitted data for secure, remote CLI access over IP networks
IEEE 802.1X-based dynamic delivery of QoS, ACLs, and VLANs
allows complete control over user network access
Guest VLAN
provides a browser-based environment to authenticated clients, similar to IEEE 802.1X
Port isolation
secures and adds privacy, and prevents malicious attackers from obtaining user information
Port security
allows access only to specified MAC addresses, which can be learned or specified by the administrator
MAC-based authentication
allows or denies access to the switch based on a client MAC address
IP Source Guard
helps prevent IP spoofing attacks
HTTPS management
provides secure Web management
URPF
limits malicious traffic on a network
Multi-Customer Edge (MCE)-Multicast Virtual Routing and Forwarding (MVRF)
QuickSpecs
HP 5820 Switch Series
Overview
DA - 13791 North America — Version 18 — November 22, 2013 Page 4

provide MPLS Edge router support
Public Key Infrastructure (PKI)
is used to control access
Convergence
Voice VLAN
automatically assigns VLAN and priority for IP phones, simplifying network configuration and maintenance
LLDP-MED
is a standard extension that automatically configures network devices, including LLDP-capable IP phones
Internet Group Management Protocol (IGMP)
utilizes Any-Source Multicast (ASM) or Source-Specific Multicast (SSM) to manage IPv4 multicast networks; supports IGMPv1, v2,
and v3
Protocol Independent Multicast (PIM)
defines modes of Internet multicasting to allow one-to-many and many-to-many transmission of information; PIM Dense Mode
(DM), Sparse Mode (SM), and Source-Specific Mode (SSM) are support
Monitor and diagnostics
Port mirroring
enables traffic on a port to be simultaneously sent to a network analyzer for monitoring
OAM (802.3ah)
operations, administration and maintenance (OAM) management capability detects data link layer problems that occurred in the
"last mile"; monitors the status of the link between the two devices
CFD (802.1ag)
connectivity fault detection (CFD) provides a Layer 2 link OAM (operations, administration, and maintenance) mechanism used
for link connectivity detection and fault locatin
Additional information
Intelligent Resilient Framework (IRF)
Creates virtual resilient switching fabrics, where two or more switches perform as a single Layer 2 switch and Layer 3
router
Does not require switches to be co-located and allows them to be part of a disaster-recovery system
Allows servers or switches to be attached using standard LACP for automatic load balancing and high availability
Simplifies network operation by eliminating the complexity of Spanning Tree Protocol, ECMP, or VRRP
OAA modules
support wireless network management and high-performance security applications; leverage network infrastructure
investment
Green IT and power
improves energy efficiency through the use of the latest advances in silicon development; shuts off unused ports and utilizes
variable-speed fans, reducing energy costs
High scalability with IRF
HP Intelligent Resilient Framework (IRF) technology simplifies the architecture of server access networks; up to nine HP
5820/5820AF stackable switches can be combined to deliver unmatched scalability of virtualized access layer switches and
flatter, two-tier FlexFabric networks using IRF, which reduces cost and complexity
Warranty and support
1-year warranty
with advance replacement and 10-calendar-day delivery (available in most countries)
QuickSpecs
HP 5820 Switch Series
Overview
DA - 13791 North America — Version 18 — November 22, 2013 Page 5

Electronic and telephone support
limited electronic and telephone support is available from HP; to reach our support centers, refer to
www.hp.com/networking/contact-support ; for details on the duration of support provided with your product purchase, refer to
www.hp.com/networking/warrantysummary
Software releases
to find software for your product, refer to www.hp.com/networking/support ; for details on the software releases available with
your product purchase, refer to www.hp.com/networking/warrantysummary
QuickSpecs
HP 5820 Switch Series
Overview
DA - 13791 North America — Version 18 — November 22, 2013 Page 6

Build To Order:
BTO is a standalone unit with no integration. BTO products ship standalone are not part of a CTO or Rack-
Shippable solution.
Standard Switch Chassis
HP 5820-14XG-SFP+ Switch with 2 Slots JC106A
4 RJ-45 autosensing 10/100/1000 ports
2 module slots
14 fixed 1000/10000 SFP+ ports
min=0 \ max=14 SFP+ Transceivers
1 Power Supply Required
2U - Height
See
Configuration
Note:1
HP 5820-24XG-SFP+ Switch JC102A
4 RJ-45 autosensing 10/100/1000 ports
24 fixed 1000/10000 SFP+ ports
min=0 \ max=24 SFP+ Transceivers
1 Power Supply Required
1U - Height
See
Configuration
Note:1
HP 5820AF-24XG Switch JG219A
4 RJ-45 autosensing 10/100/1000 ports
24 fixed 1000/10000 SFP+ ports
min=0 \ max=24 SFP+ Transceivers
1 Power Supply Required
2 Fan Trays Required
1U - Height
See
Configuration
Note:1
Configuration Rules:
Note 1 The following Transceivers install into this Module (Max = 14 or 24 depending on Switch) (Use #0D1 or #B01
if switch is CTO):
HP X130 SFP+ LC SR Transceiver JD092B
HP X130 SFP+ LC LRM Transceiver JD093B
HP X130 SFP+ LC LR Transceiver JD094B
HP X130 10G SFP+ LC ER 40km Transceiver JG234A
HP X240 10G SFP+ SFP+ 0.65m DAC Cable JD095C
HP X240 10G SFP+ SFP+ 1.2m DAC Cable JD096C
HP X240 10G SFP+ SFP+ 3m DAC Cable JD097C
HP X240 10G SFP+ SFP+ 5m DAC Cable JG081C
HP X125 1G SFP LC LH40 1310nm Transceiver JD061A
HP X120 1G SFP LC LH40 1550nm Transceiver JD062A
HP X125 1G SFP LC LH70 Transceiver JD063B
HP X120 1G SFP LC SX Transceiver JD118B
HP X120 1G SFP LC LX Transceiver JD119B
HP X120 1G SFP RJ45 T Transceiver JD089B
QuickSpecs
HP 5820 Switch Series
Configuration
DA - 13791 North America — Version 18 — November 22, 2013 Page 7

Box Level Integration CTO Models
CTO Solution Sku
HP 58xx CTO Switch Solution JG478A
SSP trigger sku
CTO Base Sku
HP 5820-14XG-SFP+ w/2 Slots CTO Switch JC106AC
4 RJ-45 autosensing 10/100/1000 ports
2 module slots
14 fixed 1000/10000 SFP+ ports
min=0 \ max=14 SFP+ Transceivers
1 Power Supply Required
2U - Height
See
Configuration
Note:1,4
HP 5820-24XG-SFP+ CTO Switch JC102AC
4 RJ-45 autosensing 10/100/1000 ports
24 fixed 1000/10000 SFP+ ports
min=0 \ max=24 SFP+ Transceivers
1 Power Supply Required
1U - Height
See
Configuration
Note:1,4
HP 5820AF-24XG Switch JG219A
4 RJ-45 autosensing 10/100/1000 ports
24 fixed 1000/10000 SFP+ ports (min=0 \ max=24 SFP+ Transceivers)
1 Power Supply Required
2 Fan Trays Required
1U - Height
See
Configuration
Note:1, 4
Configuration Rules:
Note 1 The following Transceivers install into this Module (Max = 14 or 24 depending on Switch): (Use #0D1 if switch
is CTO)
HP X130 SFP+ LC SR Transceiver JD092B
HP X130 SFP+ LC LRM Transceiver JD093B
HP X130 SFP+ LC LR Transceiver JD094B
HP X130 10G SFP+ LC ER 40km Transceiver JG234A
HP X240 10G SFP+ SFP+ 0.65m DAC Cable JD095C
HP X240 10G SFP+ SFP+ 1.2m DAC Cable JD096C
HP X240 10G SFP+ SFP+ 3m DAC Cable JD097C
HP X240 10G SFP+ SFP+ 5m DAC Cable JG081C
HP X125 1G SFP LC LH40 1310nm Transceiver JD061A
HP X120 1G SFP LC LH40 1550nm Transceiver JD062A
QuickSpecs
HP 5820 Switch Series
Configuration
DA - 13791 North America — Version 18 — November 22, 2013 Page 8

HP X125 1G SFP LC LH70 Transceiver JD063B
HP X120 1G SFP LC SX Transceiver JD118B
HP X120 1G SFP LC LX Transceiver JD119B
HP X120 1G SFP RJ45 T Transceiver JD089B
Note 4 If the Switch Chassis is to be Box Level Factory Integrated (CTO), Then the #0D1 is required on the Switch
Chassis and integrated to the JG478A - HP 58xx CTO Enablement. (Max 1 switch per SSP)
Rack Level Integration CTO Models
Standard Switch Chassis
HP 5820-14XG-SFP+ Switch with 2 Slots JC106A
4 RJ-45 autosensing 10/100/1000 ports
2 module slots
14 fixed 1000/10000 SFP+ ports
min=0 \ max=14 SFP+ Transceivers
1 Power Supply Required
2U - Height
See
Configuration
Note:1, 11
HP 5820-24XG-SFP+ Switch JC102A
4 RJ-45 autosensing 10/100/1000 ports
24 fixed 1000/10000 SFP+ ports
min=0 \ max=24 SFP+ Transceivers
1 Power Supply Required
1U - Height
See
Configuration
Note:1, 11
HP 5820AF-24XG Switch JG219A
4 RJ-45 autosensing 10/100/1000 ports
24 fixed 1000/10000 SFP+ ports (min=0 \ max=24 SFP+ Transceivers)
1 Power Supply Required
2 Fan Trays Required
1U - Height
See
Configuration
Note:1, 4, 11
Configuration Rules:
Note 1 The following Transceivers install into this Module (Max = 14 or 24 depending on Switch):
HP X130 SFP+ LC SR Transceiver JD092B
HP X130 SFP+ LC LRM Transceiver JD093B
HP X130 SFP+ LC LR Transceiver JD094B
HP X130 10G SFP+ LC ER 40km Transceiver JG234A
HP X240 10G SFP+ SFP+ 0.65m DAC Cable JD095C
HP X240 10G SFP+ SFP+ 1.2m DAC Cable JD096C
HP X240 10G SFP+ SFP+ 3m DAC Cable JD097C
HP X240 10G SFP+ SFP+ 5m DAC Cable JG081C
HP X125 1G SFP LC LH40 1310nm Transceiver JD061A
QuickSpecs
HP 5820 Switch Series
Configuration
DA - 13791 North America — Version 18 — November 22, 2013 Page 9

HP X120 1G SFP LC LH40 1550nm Transceiver JD062A
HP X125 1G SFP LC LH70 Transceiver JD063B
HP X120 1G SFP LC SX Transceiver JD118B
HP X120 1G SFP LC LX Transceiver JD119B
HP X120 1G SFP RJ45 T Transceiver JD089B
Note 4 Switch Height is 2U if the JC682A - HP A58x0AF Bck(pwr)-Frt(ports) Fan Tray is ordered #0D1 with this switch.
REMARK: This only applies for CTO Rack Level Integration.
Note 11 If HP CTO Switch Chassis is selected for Rack Level Integration, Then the Switch needs to integrate (with
#0D1) to the HP Rack.
Enter the following menu selections as integrated to the CTO Model X server above if order is factory built.
Modules
Ethernet Modules
(JC106x and JG259x Switch Only ) System (std 0 // max 2) User Selection (min 0 // max 2) per chassis
HP 5800 4-port 10GbE SFP+ Module JC091A
min=0 \ max=4 SFP + Transceivers See
Configuration
Note:1
HP 5800 2-port 10GbE SFP+ Module JC092B
min=0 \ max=2 SFP + Transceivers See
Configuration
Note:1
HP 5820 4-port 8/4/2 Gbps FCoE SFP+ Mod JC530A
min=0 \ max=4 SFP + Transceivers See
Configuration
Note:1
Configuration Rules:
Note 1 The following Transceivers install into this Module: (Use #0D1 or #B01 if switch is CTO)
HP X130 SFP+ LC SR Transceiver JD092B
HP X130 SFP+ LC LRM Transceiver JD093B
HP X130 SFP+ LC LR Transceiver JD094B
HP X130 10G SFP+ LC ER 40km Transceiver JG234A
HP X240 10G SFP+ SFP+ 0.65m DAC Cable JD095C
HP X240 10G SFP+ SFP+ 1.2m DAC Cable JD096C
HP X240 10G SFP+ SFP+ 3m DAC Cable JD097C
HP X240 10G SFP+ SFP+ 5m DAC Cable JG081C
QuickSpecs
HP 5820 Switch Series
Configuration
DA - 13791 North America — Version 18 — November 22, 2013 Page 10