HP Xw9400 - Workstation - 16 GB RAM User manual

NVIDIA Quadro FX5800 Graphics Card
installation
Introduction
This document describes how to install an NVIDIA Quadro FX5800 Graphics Card with an auxiliary
power adapter cable in an HP Workstation.
Kit contents
●NVIDIA Quadro FX5800 Graphics Card
●Auxiliary power adapter cable
●Card support bracket for HP xw8600 and xw9400 Workstations
●Fan for HP xw8600 Workstation
●Warranty information
Before you begin
To determine the compatibility of this product with your HP workstation, see QuickSpecs online at
http://www.hp.com/go/productbulletin.
Before installing an NVIDIA FX5800 Quadro graphics card, ensure the following criteria are met:
●HP 800 Workstations must contain an 1110 Watt power supply.
●HP xw8600 and xw9400 Workstations must contain a 1050 Watt power supply for dual cards. (1050
Watt power supply is recommended for single card.)
●System memory cannot exceed 32 GB with dual FX5800 cards (HP xw8600 Workstations).
●System cannot contain Dual FSB1600/ Quad core processors with dual FX5800 cards (HP xw8600
Workstations).
© 2008–2009 Hewlett-Packard Development Company, L.P.
Printed in the U.S.
ENWW Introduction 1

Warnings and cautions
WARNING! Any surface or area of the equipment marked with this symbol indicates the presence
of an electrical shock hazard. To reduce the risk of injury from electrical shock, do not open any enclosed
area marked with this symbol.
WARNING! To reduce the risk of electric shock or damage to your equipment:
— Do not disable the power cord grounding plug. The grounding plug is an important safety feature.
— Plug the power cord in a grounded (earthed) outlet that is easily accessible at all times.
— Disconnect power from the equipment by unplugging the power cord from the electrical outlet.
WARNING! Any surface or area of the equipment marked with this symbol indicates the presence
of a hot surface or hot component. If this surface is contacted, the potential for injury exists. To reduce
the risk of injury from a hot component, enable the surface to cool before touching.
WARNING! If a product is shipped in packaging marked with this symbol, , the product must always
be lifted by two persons to avoid personal injury due to product weight.
WARNING! To reduce the risk of serious injury, read the Safety & Comfort Guide. It describes proper
workstation setup, posture, health, and work habits for computer users, and provides important electrical
and mechanical safety information. This guide is located at http://www.hp.com/ergo and on the
documentation CD (if one is included with the product).
CAUTION: Static electricity can damage the electronic components of the workstation. Before
beginning these procedures, be sure you discharge static electricity by briefly touching a grounded metal
object.
CAUTION: To prevent damage to the workstation, observe the following Electrostatic Discharge
(ESD) precautions while performing the system parts removal and replacement procedures:
— Work on a static-free mat.
— Wear a static strap to ensure that any accumulated electrostatic charge is discharged from your body
to the ground.
— Create a common ground for the equipment you are working on by connecting the static-free mat,
static strap, and peripheral units to that piece of equipment.
NOTE: HP accessories are for use in HP Workstation products. They have been extensively tested
for reliability and are manufactured to high quality standards.
2 NVIDIA Quadro FX5800 Graphics Card installation ENWW

Step 1—Preparing for component installation
NOTE: Workstation models vary. All illustrations are examples only.
Accessing the internal components of the workstation
1. If you need help preparing the workstation for this installation, consult the removal and replacement
procedures in the service guide for your workstation at http://www.hp.com/support/
workstation_manuals.
NOTE: For the HP Workstation series, these procedures are also available in the User
Guide on the Documentation and Diagnostics CD that shipped with your workstation.
2. Power down the workstation, and then disconnect the power cord.
3. Power down all external devices, and then disconnect them from the workstation.
4. Remove the side access panel.
Removing components
1. If present, remove the card support to enable access to the expansion slots and system board
connectors.
2. Select a PCIe-x16 expansion slot.
a. Open the expansion slot retention clamp .
b. Remove the applicable expansion slot covers
2
.
NOTE: The FX5800 graphics card occupies two expansion slots on the system board. HP
recommends placing the keyed components of the card in the primary graphics slot. To identify a
PCI Express (PCIe)-x16 expansion slot, see the service label on the workstation access panel.
NOTE: For optimal cooling, keep the expansion slot adjacent to the fan free or filled with an
expansion card that does not obstruct the fan inlet of the FX5800 card.
Figure 1 Opening the retainer and removing the slot covers
ENWW Step 1—Preparing for component installation 3

Step 2—Installing the front PCI fan in the HP xw8600
Workstation
CAUTION: To prevent overheating an HP xw8600 Workstation, a front PCI fan is required when
installing the NVIDIA Quadro FX5800 graphics card. If the HP xw8600 Workstation includes dual high-
performance graphics cards and lacks a front PCI fan, the BIOS detects an illegal cooling configuration
error and reports that the front PCI fan is missing.
1. Remove the card guide from the chassis.
a. Release the two card guide latches .
b. Pivot the card guide toward the system board
2
.
c. Lift the card guide out of the chassis .
Figure 2 Removing the card guide from the chassis
4 NVIDIA Quadro FX5800 Graphics Card installation ENWW

2. Attach the front fan to the card guide.
a. Place the fan in the card guide with the fan label facing into the card guide and the fan protector
screen facing outward.
b. Place the fan wire through the slot in the card guide.
c. Snap the fan into place in the card guide.
Figure 3 Attaching the front fan to the card guide
3. Install the front fan/card guide assembly.
a. Lower the front fan/card guide assembly into the chassis .
b. Rotate the assembly back
2
, and then snap it into place.
c. Connect the front fan wire connector to the front fan connector on the system board .
NOTE: To identify the front fan connector on the system board, see the service label on the
workstation access panel.
Figure 4 Installing the front fan/card guide assembly in the chassis
ENWW Step 2—Installing the front PCI fan in the HP xw8600 Workstation 5

Step 3—Installing the graphics card
NOTE: The FX5800 graphics card occupies two expansion slots on the system board. HP
recommends placing the keyed components of the card in the primary graphics slot. To identify a PCI
Express (PCIe)-x16 expansion slot, see the service label on the workstation access panel.
Position the graphics card.
1. While lowering the card into the chassis, rotate the graphics card bulkhead under the rear chassis
lip .
2. Align the card in a groove of the card guide
2
and pivot the card until level.
3. Press securely into the PCIe expansion slot .
Figure 5 Installing the graphics card
6 NVIDIA Quadro FX5800 Graphics Card installation ENWW

Step 4—Connecting the power
1. Close the expansion slot retention clamp to secure the card in the slot .
2. Connect the 6-to-8 pin auxiliary power adapter cable, supplied with this kit, to the workstation
auxiliary power supply
2
, and then to the FX5800 card .
NOTE: No connection is made at point . If a label covers the outlet at , do not remove it.
Figure 6 Installing the 6-to-8 pin power adapter cable
Step 5—Installing the card support
HP xw8600 and xw9400 Workstations
To prepare and install the card support bracket:
1. Insert an additional arm in the card support , if applicable.
2. Slide the arm back to lock it into place
2
.
3. Hook the support bracket in the openings along the edge of the rear of the chassis .
4. Compress the spring of the support arm until the arm locks into place .
Figure 7 Installing a card support (HP xw8600 and xw9400 Workstations)
ENWW Step 4—Connecting the power 7

Step 6—Reassembling the workstation
1. Reinstall the workstation card support, if applicable.
2. Reinstall the side access panel.
3. Reconnect power to the workstation and all external devices.
4. Restore power to the workstation and all external devices.
Step 7—Configuring the software
For instructions on loading and setting up the graphics drivers, see the manufacturer’s documentation
shipped with the NVIDIA Quadro graphics card.
At the time of component installation, look for device firmware and driver updates, designated for your
workstation model and operating system from http://www.hp.com/go/workstationsupport.
Japanese 日本語
This document is available in Japanese. See http://www.hp.com/support/workstation_manuals, then
select your workstation product and select Japanese from the drop down Manual Language menu.
このドキュメントは日本語版が用意されています。http://www.hp.com/support/workstation_manuals
にアクセスし、ご使用のワークステーション製品を選択し、Manual Language ドロップダウン メニ
ューから Japanese を選択してください。
8 NVIDIA Quadro FX5800 Graphics Card installation ENWW