HPE Aruba 2930F User manual

Aruba 2930F 8G PoE+ Switch
Quick Setup Guide and
Safety/Regulatory Information
Abstract
Use this guide to assist in the basic set-up of the JL258A Aruba 2930F 8G PoE+ 2SFP+ Switch.
*5200-2049*
Part Number: 5200-2049
Published: July 2016
Edition: 1

©Copyright 2016 Hewlett Packard Enterprise Development LP
The information contained herein is subject to change without notice. The only warranties for Hewlett Packard Enterprise products and services
are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting
an additional warranty. Hewlett Packard Enterprise shall not be liable for technical or editorial errors or omissions contained herein.
Confidential computer software. Valid license from Hewlett Packard Enterprise required for possession, use, or copying. Consistent with FAR
12.211 and 12.212, Commercial Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed
to the U.S. Government under vendor's standard commercial license.
Links to third-party websites take you outside the Hewlett Packard Enterprise website. Hewlett Packard Enterprise has no control over and is not
responsible for information outside the Hewlett Packard Enterprise website.
Applicable products
JL258AAruba 2930F 8G PoE+ 2SFP+ Switch

Contents
Aruba 2930F 8G Switch Quick Setup Guide and Safety/Regulatory
Information..............................................................................................................4
Aruba 2930F warm product and other mounting information...............................................................4
Installation precautions.........................................................................................................................4
Power supply operation........................................................................................................................5
Prepare for installation..........................................................................................................................6
Mounting the JL258A Aruba2930F 8–port switch.................................................................................7
(Optional) Attaching the JL312A Power Adapter Shelf to the Aruba 2930F 8G switch...................8
(Optional) Attaching the JL311A cable guard to the Aruba 2930F 8G switch.................................8
Mounting the Aruba 2930F 8G switch without a cable guard..........................................................8
Rack mounting...........................................................................................................................9
Tabletop or desktop mounting....................................................................................................9
Wall or under-table mount........................................................................................................10
Connecting the switch to the network.................................................................................................12
SFP/SFP+ installation notes...............................................................................................................14
Use only genuine HPE Aruba SFP/SFP+ transceivers.................................................................14
Hot Swapping SFP/SFP+ transceivers..........................................................................................14
SFP/SFP+ connections to devices with fixed speed/duplex configurations..................................14
Switch Operating System Software....................................................................................................14
Power cords........................................................................................................................................15
Safety and compliance information.....................................................................................................15
Aruba 2930F Switch Safety and Regulatory Information....................................................................15
Japan VCCI class A statement...........................................................................................................16
Korea EMC class A statement............................................................................................................17
EAC....................................................................................................................................................17
Documentation feedback....................................................................................................................17
Contents 3

Aruba 2930F 8G Switch Quick Setup Guide and
Safety/Regulatory Information
NOTE: The switch drawings in this document are for illustration only and may not match your
particular switch model.
NOTE: For switch and accessories installation information, browse to the manuals for your
switch model at www.hpe.com/networking/ResourceCenter.
Aruba 2930F warm product and other mounting information
•If you are mounting the Aruba 2930F 8G switch in a rack with other products, the preferred
position for the switch is at the base of the rack (for optimal cooling), or below as many of
the other products as can be accomodated, while still ensuring that the Installation Precautions
(under the WARNING!, below) regarding weight distribution are observed.
•When mounted in a rack, ensure that a 1U (44.45 mm / 1.75-inch) vertical rack space exists
between the Aruba 2930F 8G switch and the device above it.
•When mounting the Aruba 2930F 8G switch on a wall, under a table, or on a horizontal
surface, ensure that the supplied four rubber mounting feet are placed on the bottom of the
switch, as shown (under “Tabletop or desktop mounting” (page 9) ). This is required to
provide the proper thermal spacing between the switch and the mounting surface.
•Avoid obstructing the ventilation holes on the top, sides, and back of the switch.
•Do not install the Aruba 2930F 8G switch in a confined space that does not allow a free air
flow.
•When installing the switch in an enclosed space containing free air flow, ensure that any
adjacent surfaces are at least 15.3 cm (6 inches) from the sides and back of the switch.
Installation precautions
WARNING!
•The rack or cabinet should be adequately secured to prevent it from becoming unstable
and/or falling over.
•Devices installed in a rack or cabinet should be mounted as low as possible, with the heaviest
devices at the bottom and progressively lighter devices installed above.
4 Aruba 2930F 8G Switch Quick Setup Guide and Safety/Regulatory Information

CAUTION:
•Do not ship any switch in a rack without checking for restrictions in the Aruba 2930F Switches
Installation and Getting Started Guide. Otherwise, you may void the switch warranty.
•Ensure the power source circuits are properly grounded, then use the power cord supplied
with the switch to connect the AC adapter to the power source.
•Use only approved power cords with your Aruba Networking Product. Please see the power
cord information in the section titled “Power cords” (page 15) of this guide for acceptable
power cords that are appropriate for this product. Failure to use approved power cords can
result in personal injury and product damage, and may void your product warranty.
•If your installation requires a different power cord than the one supplied with the switch and
AC adapter, be sure the cord is adequately sized for the AC adapter’s current requirements.
In addition, be sure to use a power cord displaying the mark of the safety agency that defines
the regulations for power cords in your country. The mark is your assurance that the power
cord can be used safely with the switch’s AC adapter and power supply.
•When installing the switch, the AC outlet should be near the switch and should be easily
accessible in case the switch’s AC adapter must be powered off.
•Do not install the switch in an environment where the operating ambient temperature exceeds
its specification. See the section titled “Aruba 2930F Switch Safety and Regulatory
Information” (page 15).
•Ensure the switch’s AC adapter does not overload the power circuits, wiring, and over-current
protection. To determine the possibility of overloading the supply circuits, add together the
ampere ratings of all devices installed on the same circuit as the switch’s AC adapter and
compare the total with the rating limit for the circuit. The maximum ampere ratings are usually
printed on the devices, near the AC power connectors.
•For a wall-mounted Aruba 2930F 8G Switch (JL258A), face the network ports up, that is,
away from the floor. Do not wall-mount the switch with the network ports facing down (towards
the floor).
•Do not install the Aruba 2930F 8G PoE+ 2SFP+ switch in an environment where the operating
ambient temperature might exceed its specification. When mounting the switch in a rack,
ensure that a 1U (44.45mm/1.75-inch) vertical space is left for cooling between the switch
and the device above it, and at least 15.3 cm (6 inches) of space around the sides and back
of the switch. When mounted in a fully enclosed rack or cabinet, ensure that the air flow for
cooling around the top, sides, and back of the switch is not restricted. Installing the Aruba
2930F 8G PoE+ 2SFP+ Switch in an enclosed, confined space such as a small bookshelf
or unventilated cabinet is not recommended.
Power supply operation
The Aruba 2930F 8G PoE+ 2SFP SwitchAruba 2930F 8G PoE+ 2SFP Switch does not have a
power switch. It is powered on when the external AC/DC power adapter is connected to the
switch and the adapter power cord to a properly grounded power source. The external AC/DC
power adapter automatically adjusts to any voltage between 100-240 volts and either 50 or 60
Hz. The external AC/DC power adapter supplies 54 volts DC to the switch. No voltage range
settings are required.
Power supply operation 5

Prepare for installation
1. Unpack and check included parts:
•Switch
•Console cable (5188–3836)
•Accessory kits (installation hardware)
Included itemsCountPart number
Rack mount brackets (long)
nl
2
nl
5189–6934
Large screws; bracket-to-rack
nl
4
nl
Small screws; bracket-to-switch8
Wall/under-table brackets
nl
2
nl
5300–0140
Small screws; bracket-to-switch
nl
8
nl
Cable tie
nl
1
nl
Rubber foot pads4
•AC power adapter (5066–5559)
•Power cord (See “Power cords” (page 15).
•Documentation kit (5200–1998)
NOTE: Screws for mounting the switch on a wall or under a table are not included. If you
plan to mount the switch on a wall or under a table, you will need to provide four 5/8–inch
number 12 wood screws.
2. Prepare for installation.
CAUTION: To avoid personal injury or product damage, review the “Installation precautions”
(page 4) before beginning the installation.
3. Power-on and verify that the self-test completes normally. An Aruba 2930F 8G switch does
not contain a power on/off switch. It is turned on by connecting the power cord to the AC
power adapter and to a properly-grounded AC power source, then connecting the AC adapter
to the switch.
6 Aruba 2930F 8G Switch Quick Setup Guide and Safety/Regulatory Information

1
2
3
4
5
6
Port LEDs: Off after self-test unless a network cable is connected and
the port is receiving link beat.
1
Global Status LED: Green after self-test in default configuration.2
Locator/Unit-Identification LED: Off after self-test.3
Speed Mode Selected LED: Off after self-test in default configuration.4
PoE Mode Selected LED (Only on Aruba 2930F models that support
PoE+ operation): Off after self-test in default configuration.
5
User Mode Selected: Off after self-test in default configuration.6
4. Disconnect the AC adapter from the switch and remove the power cord from the power
source.
Mounting the JL258A Aruba2930F 8–port switch
Supported mounting options for the Aruba 2930F 8G switch include:
•Rack mount
•Tabletop or desktop mount
•Under-table mount
•Wall mount
Mounting the JL258A Aruba2930F 8–port switch 7

(Optional) Attaching the JL312A Power Adapter Shelf to the Aruba 2930F 8G switch
To install the optional Power Adapter Shelf, see the printed instructions provided with the shelf,
then return to this guide and go to the next section, “(Optional) Attaching the JL311A cable guard
to the Aruba 2930F 8G switch” (page 8).
(Optional) Attaching the JL311A cable guard to the Aruba 2930F 8G switch
•If you do not have the optional J311A cable guard to attach to the switch,, go to the next
section, “Mounting the Aruba 2930F 8G switch without a cable guard” (page 8).
•If you have the optional J311A cable guard to attach to the switch, go to the printed
instructions shipped with the cable guard to complete the setup process. After installing the
optional cable guard, return to this guide or go to the Aruba 2930F Switches Installation and
Getting Started Guide for information on topics such as:
◦SFP/SFP+ installation notes
◦Links to the latest software version and manuals for your switch
◦Power cords
◦Safety and regulatory information
(You can access the Installation and Getting Started Guide at www.hpe.com/networking/
ResourceCenter).
Mounting the Aruba 2930F 8G switch without a cable guard
Use the instructions in this section to mount the Aruba 2930F 8G switch if you do not plan to
attach the optional JL311A cable guard to the switch.
8 Aruba 2930F 8G Switch Quick Setup Guide and Safety/Regulatory Information

Rack mounting
1. Install mounting brackets (included) for use in a two-post rack. You can orient the brackets
to be either flush with the switch front or offset from the switch front, as illustrated below.
NOTE: If the JL312A Power Adapter Shelf is installed, then position the mounting brackets
over the center set of screw holes on each side of the switch instead of the forward set on
each side.
1
2
1
1
2
2
2. Secure the mounting brackets to a two-post rack. The illustration to the right shows the
recommended positioning of the mounting brackets when the optional JL312A Power Adapter
Shelf is used with the switch.
Tabletop or desktop mounting
• Attach the four self-adhesive pads (included) to the bottom corners of the switch and place
the switch on a secure tabletop or desktop surface.
Mounting the JL258A Aruba2930F 8–port switch 9

Wall or under-table mount
You can mount the Aruba 2930F 8G PoE+ 2SFP+ Switch on a wall with the network ports facing
up, or under a table.
WARNING!
•For safe operation, do not install the switch with the side ventilation holes facing down.
•For under table mounting, the top-of-switch ventilation holes must be facing down.
1. To help provide proper ventilation, attach the four self-adhesive pads (included) to the bottom
corners of the switch.
2. Install short mounting brackets (included).
1
1
2
2
10 Aruba 2930F 8G Switch Quick Setup Guide and Safety/Regulatory Information

3. Secure the switch on the wall or under-table location using four 5/8–inch number 12 wood
screws (not included).
1
2
2
Mounting the JL258A Aruba2930F 8–port switch 11

Connecting the switch to the network
1. (Optional) Connect an RJ-45 console cable (included) and/or a micro-USB console cable
(not included) to a VT-100 terminal or a PC (running suitable terminal emulation software).
NOTE: If both cables are connected, input is accepted only from the Micro USB connector.
For more information, see the information on connecting a management console in the
Aruba 2930F Switches Installation and Getting Started Guide.
2. (Optional) Insert transceivers.
12 Aruba 2930F 8G Switch Quick Setup Guide and Safety/Regulatory Information

NOTE: To ensure proper operation of your switch, use only genuine HPE Aruba SFP/SFP+
transceivers supported by your switch. For more information on using transceivers, see
“SFP/SFP+ installation notes” (page 14).
3. Connect network cables.
NOTE: In the factory default configuration, the switch automatically obtains its IP network
settings from a DHCP or BootP server after connecting to the network. If you do not use direct
console access to initially determine the switch IP address, you can determine the assigned IP
address by inspecting your DHCP/BootP server or by querying LLDP information from another,
directly connected neighbor switch. CLI LLDP commands for an ArubaOS neighbor switch are
listed below.
Connecting the switch to the network 13

For the specified port on the neighbor switch, lists the IP
address and other data for the directly connected Aruba 2930F
show lldp info remote port_#
switch (where port_# is the port used on the neighbor switch
to access the Aruba 2930F switch you are setting up).
Lists IP address and other data on all active ports on the
neighbor switch.
show lldp info remote all
SFP/SFP+ installation notes
NOTE: To ensure proper operation of your switch, use only the genuine HPE Aruba SFP/SFP+
transceivers supported by your switch. When selecting a fiber SFP device, make sure it can
function at a temperature that is not less than the recommended maximum operational temperature
of the product. Use only approved Laser Class 1 SFP transceivers.
Use only genuine HPE Aruba SFP/SFP+ transceivers
Non-HPE Aruba SFP/SFP+ transceivers are not supported. Use of genuine HPE Aruba products
ensures that your network maintains optimal performance and reliability. Should you require
additional transceivers, please contact an HPE Aruba sales representative or an authorized
reseller. For transceiver support information for your switch model, see the following two support
matrixes in the Hewlett Packard Enterprise Information Library at www.hpe.com/networking/
ResourceCenter:
•HPE Networking Legacy ProCurve Product Family Mini-GBIC and SFP Support Matrix
•HPE Networking Legacy ProCurve Product Family 10–GBE Transceiver Support Matrix
Hot Swapping SFP/SFP+ transceivers
Supported SFP/SFP+ transceivers that you can install in your HPE Aruba switch can be “hot
swapped” – removed and installed while the switch is receiving power. However, you should
disconnect the network cables from the SFP/SFP+ transceivers before hot-swapping them.
When you replace an SFP/SFP+ transceiver with another of a different type, the switch may
retain selected port-specific configuration settings that were configured for the replaced unit. Be
sure to validate or reconfigure port settings as required.
SFP/SFP+ connections to devices with fixed speed/duplex configurations
When connecting a device to your switch port that contains an SFP/SFP+ transceiver, the speed
and duplex settings of the switch port and the connected device must match. Otherwise, you
may not get a link. For some older network devices, including some older Hewlett Packard
Enterprise devices, the default speed/duplex settings may be predefined (for example, to 1000
Mbps/Full Duplex), or otherwise set differently from the default configuration of your switch port.
Because of these default speed/duplex considerations, you should make sure that devices
connected to your SFP/SFP+ ports are properly configured. At a minimum, make sure the
configurations match.
Switch Operating System Software
For the latest software version supported by your switch, visit http://www.hpe.com/networking/
support.
For software installation and management, the Basic Operation Guide and other software
documentation for your switch at www.hpe.com/networking/ResourceCenter.
14 Aruba 2930F 8G Switch Quick Setup Guide and Safety/Regulatory Information

Power cords
Use one of the following power cords for an Aruba 2930F switch:
8121–1004Israel8121–0729Argentina
8121–1143Japan8121-0837Australia/New Zealand
8121–0738Switzerland8121-1071Brazil
8121–0737South Africa8121–0735Chile
8121-0964Taiwan8121–0943China
8121-0734Philippines/Thailand8121–0731Continental Europe/South
Korea
8121–0739UK/Hong Kong/Singapore/Malaysia8121–0733Denmark
8121-1141US/Canada/Mexico8121–0564India
Safety and compliance information
For important safety, environmental, and regulatory information, see Safety and Compliance
Information for Server, Storage, Power, Networking, and Rack Products, available at http://
www.hpe.com/support/Safety-Compliance-EnterpriseProducts.
Aruba 2930F Switch Safety and Regulatory Information
Aruba 2930F SwitchesCategory
32°F to 113°F (0°C to 45°C) up to 5000 FtEnvironmental
•Operating Temperature: 32°F to 104°F (0°C to 40°C) up to 10000 Ft
15% to 95% at 104°F (40°C) non-condensing
•Operating Relative Humidity:
–40°F to 158°F (–40°C to 70°C) up to 15000 ft
•Non-Operating/Storage Temperature:
15% to 95% at 149°F (65°C), non-condensing
•Non-Operating/Storage Relative Humidity:
3.0 km (10,000 ft)
•Maximum Operating Altitude:
4.6 km (15,000 ft)
•Maximum Non-Operating Altitude:
Side-to-SideAirflow direction
EN 60950-1:2006 +A11:2009 +A1:2010
+A12:2011+A2:2013
Safety-EU
IEC60950-1:2005 Ed.2; Am 1:2009+A2:2013Safety- World Wide
UL60950-1, CSA 22.2 No 60950-1North American
EN60850-1:2007 / IEC 60825-1: 2007 Class1Lasers
Class 1 Laser Products / Laser Klasse 1
EN 55022:2010, Class A
nl
EMC:
EN 55024:2010
nl
EN 6100–3–2:2006+A1:2009+A2:2009, Class A
nl
EN 61000–3–3:2008
nl
FCC CFR 47 Part 15:2010, Class A
EN 50581:2012RoHS:
Power cords 15

AC power
nl
frequency
nl
range
PoE+
nl
available
nl
power
Maximum DC
output current
Maximum
nl
DC Output
voltage
Maximum AC
nl
input current
Rated AC
nl
input voltage
2930F
8G
PoE+
2SFP+
switch
electrical
50/60 Hz124W3.33A54V DC2.6A100–240VAC
Adapter
AcousticsSwitch Model
Sound Power (LWAd) 0 BelAruba 2930F 8G PoE+ 2SFP+ Switch (JL258A)
Sound Pressure (LpAm) (Bystander) 0 dB
(no fans)
CAUTION: Disconnect all power supply cords before servicing.
Table 1 Japan power cord warning
Japan Power Cord Warning
Table 2 China Altitude Warning
China Altitude Warning
Interior Wiring
Warning
Este equipamento deve ser conectado obrigatoriamente em tomada de rede de energia
elétrica que possua aterramento (três pinos), conforme a Norma NBR ABNT 5410, visando
a segurança dos usuários contra choques elétricos.)
Brazil Statement
Japan VCCI class A statement
16 Aruba 2930F 8G Switch Quick Setup Guide and Safety/Regulatory Information

Korea EMC class A statement
EAC
Russia/Belarus/Kazakhstan/CEE Safety:
Documentation feedback
Hewlett Packard Enterprise is committed to providing documentation that meets your needs. To
help us improve the documentation, send any errors, suggestions, or comments to Documentation
Feedback ([email protected]). When submitting your feedback, include the document
title, part number, edition, and publication date located on the front cover of the document. For
online help content, include the product name, product version, help edition, and publication date
located on the legal notices page.
Korea EMC class A statement 17