HPE JH323A User manual

HPE FlexNetwork 5130 HI Switch Series
Installation Guide
Part number: 5998-8420d
Document version: 6W102-20161101

© Copyright 2016 Hewlett Packard Enterprise Development LP
The information contained herein is subject to change without notice. The only warranties for Hewlett Packard
Enterprise products and services are set forth in the express warranty statements accompanying such
products and services. Nothing herein should be construed as constituting an additional warranty. Hewlett
Packard Enterprise shall not be liable for technical or editorial errors or omissions contained herein.
Confidential computer software. Valid license from Hewlett Packard Enterprise required for possession, use, or
copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software
Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under vendor’s
standard commercial license.
Links to third-party websites take you outside the Hewlett Packard Enterprise website. Hewlett Packard
Enterprise has no control over and is not responsible for information outside the Hewlett Packard Enterprise
website.
Acknowledgments
Intel®, Itanium®, Pentium®, Intel Inside®, and the Intel Inside logo are trademarks of Intel Corporation in the
United States and other countries.
Microsoft® and Windows® are trademarks of the Microsoft group of companies.
Adobe® andAcrobat® are trademarks ofAdobe Systems Incorporated.
Java and Oracle are registered trademarks of Oracle and/or its affiliates.
UNIX® is a registered trademark of The Open Group.

i
Contents
Preparing for installation ················································································· 1
Safety recommendations ···································································································································1
Examining the installation site····························································································································2
Temperature/humidity ································································································································2
Cleanliness·················································································································································2
EMI·····························································································································································3
Laser safety················································································································································3
Installation tools ·················································································································································3
Installation accessories······································································································································4
Installing the switch························································································· 6
Installing the switch in a 19-inch rack ················································································································7
Installation methods ···································································································································7
Mounting bracket kits ·································································································································8
Rack-mounting by using front mounting brackets ······················································································8
Rack-mounting by using front and rear mounting brackets (HPE 5130 24G PoE+ 4SFP+ 1-slot HI and HPE
5130 48G PoE+ 4SFP+ 1-slot HI)············································································································12
Mounting the switch on a workbench···············································································································15
Grounding the switch ·······································································································································15
Grounding the switch with a grounding strip ····························································································15
Grounding the switch with a grounding conductor buried in the earth ground ·········································17
Grounding the switch by using the AC power cord ··················································································18
Installing/removing a power supply··················································································································18
Installing a PSR150(JD362A, JD362B, JD366A, or JD366B) power supply············································19
Removing a PSR150(JD362A, JD362B, JD366A, or JD366B) power supply··········································20
Installing a PSR720-56A/PSR1110-56A (JG544A/JG545A) power supply ·············································20
Removing a PSR720-56A/PSR1110-56A (JG544A/JG545A) power supply ···········································22
Connecting the power cord ······························································································································22
Connecting a PSR150-D/PSR150-D1 (JD366A/JD366B) power supply ·················································23
Connecting a PSR720-56A (JG544A)/PSR1110-56A (JG545A)/PSR150-A (JD362A)/PSR150-A1
(JD362B) power supply····························································································································24
Installing/removing an interface card ···············································································································24
Installing an interface card ·······················································································································25
Removing an interface card ·····················································································································26
Verifying the installation ···································································································································26
Accessing the switch for the first time··························································· 28
Setting up the configuration environment ········································································································28
Connecting the console cable··························································································································28
Connecting the Mini USB console cable ··········································································································29
Setting terminal parameters·····························································································································31
Powering on the switch ····································································································································31
Setting up an IRF fabric ················································································ 33
IRF fabric setup flowchart ································································································································33
Planning IRF fabric setup·································································································································34
Planning IRF fabric size and the installation site······················································································34
Identifying the master switch and planning IRF member IDs···································································34
Planning IRF topology and connections···································································································34
Identifying physical IRF ports on the member switches ···········································································35
Planning the cabling scheme ···················································································································36
Configuring basic IRF settings ·························································································································38
Connecting the physical IRF ports ···················································································································38
Verifying the IRF fabric setup···························································································································39
Maintenance and troubleshooting································································· 40
Power supply failure·········································································································································40

ii
Symptom ··················································································································································40
Solution ····················································································································································40
Fan tray failure ·················································································································································40
Removing a fan tray ·································································································································41
Installing a fan tray ···································································································································41
Configuration terminal display problems··········································································································42
No display ················································································································································42
Garbled display ········································································································································43
Appendix A Chassis views and technical specifications ······························· 44
Chassis views ··················································································································································44
HPE 5130 24G 4SFP+ 1-slot HI ··············································································································44
HPE 5130 24G PoE+ 4SFP+ 1-slot HI·····································································································45
HPE 5130 48G 4SFP+ 1-slot HI ··············································································································46
HPE 5130 48G PoE+ 4SFP+ 1-slot HI·····································································································47
Technical specifications ···································································································································48
Appendix B FRUs and compatibility matrixes ··············································· 51
FRUs and compatibility matrixes ·····················································································································51
Hot swappable power supplies ························································································································51
Hot swappable interface cards·························································································································52
Appendix C Ports and LEDs ········································································· 54
Ports·································································································································································54
Console port·············································································································································54
Management Ethernet port ······················································································································54
USB port···················································································································································54
10/100/1000Base-T autosensing Ethernet port ·······················································································55
SFP+ port·················································································································································55
LEDs ································································································································································58
System status LED···································································································································58
Power supply status LED ·························································································································58
LED for the port LED mode (MODE)········································································································59
10/100/1000Base-T autosensing Ethernet port LED ···············································································59
SFP+ port LED·········································································································································60
Management Ethernet port LEDs·············································································································60
Interface card status LED·························································································································60
Fan tray status LED on the fan tray ·········································································································61
Port status LED on the interface card ······································································································61
Input status LED and output status LED on the power supply·································································61
Appendix D Cooling system·········································································· 62
Document conventions and icons ································································· 63
Conventions ·····················································································································································63
Network topology icons····································································································································64
Support and other resources ········································································ 65
Accessing Hewlett Packard Enterprise Support ······························································································65
Accessing updates···········································································································································65
Websites ··················································································································································66
Customer self repair·································································································································66
Remote support········································································································································66
Documentation feedback ·························································································································66
Index ············································································································· 68

1
Preparing for installation
Table 1 HPE 5130 HI switches, power supplies, and interface cards
Product
code HPE description Alias
HPE 5130 HI switches
JH323A HPE 5130 24G 4SFP+ 1-slot HI Switch HPE 5130 24G 4SFP+ 1-slot HI
JH324A HPE 5130 48G 4SFP+ 1-slot HI Switch HPE 5130 48G 4SFP+ 1-slot HI
JH325A HPE 5130 24G PoE+ 4SFP+ 1-slot HI Switch HPE 5130 24G PoE+ 4SFP+ 1-slot HI
JH326A HPE 5130 48G PoE+ 4SFP+ 1-slot HI Switch HPE 5130 48G PoE+ 4SFP+ 1-slot HI
Power supplies
JD362A HPE A5800/A5500 150W AC Power Supply PSR150-A
JD362B HPE X361 150W AC Power Supply PSR150-A1
JD366A HPE A5800/A5500 150W DC Power Supply PSR150-D
JD366B HPE X361 150W DC Power Supply PSR150-D1
JG544A HPE X362 720W AC PoE Power Supply PSR720-56A
JG545A HPE X362 1110W AC PoE Power Supply PSR1110-56A
Interface cards
JH156A HPE 5130/5510 10GBASE-T 2-port Module LSWM2XGT2PM
JH157A HPE 5130/5510 10GbE SFP+ 2-port Module LSWM2SP2PM
For regulatory identification purposes, the HPE 5130 HI switches are assigned regulatory model
numbers (RMNs), which are listed in the following table. These regulatory numbers should not be
confused with the marketing name HPE 5130 HI, or the product codes.
Product
code RMN HPE description
JH323A BJNGA-AD0054 HPE 5130 24G 4SFP+ 1-slot HI Switch
JH324A BJNGA-AD0055 HPE 5130 48G 4SFP+ 1-slot HI Switch
JH325A BJNGA-AD0056 HPE 5130 24G PoE+ 4SFP+ 1-slot HI Switch
JH326A BJNGA-AD0057 HPE 5130 48G PoE+ 4SFP+ 1-slot HI Switch
Safety recommendations
To avoid any equipment damage or bodily injury caused by improper use, read the following safety
recommendations before installation. Note that the recommendations do not cover every possible
hazardous condition.
•Before cleaning the switch, remove all power cords from the switch. Do not clean the switch
with a wet cloth or liquid.

2
•Do not place the switch near water or in a damp environment. Prevent water or moisture from
entering the switch chassis.
•Do not place the switch on an unstable case or desk. The switch might be severely damaged in
case of a fall.
•Ensure good ventilation of the equipment room and keep the air inlet and outlet vents of the
switch free of obstruction.
•Connect the yellow-green protection grounding cable before power-on.
•Make sure the operating voltage is in the required range.
•To avoid electrical shocks, do not open the chassis while the switch is operating or when the
switch is just powered off.
•When replacing field replacable units (FRUs), including interface cards and power supplies,
wear an ESD wrist strap to avoid damaging the units.
Examining the installation site
The switch must be used indoors. You can mount your switch in a rack or on a workbench, but make
sure:
•Adequate clearance is reserved at the air inlet and outlet vents for ventilation.
•The rack or workbench has a good ventilation system.
•Identify the hot aisle and cold aisle at the installation site, and make sure ambient air flows into
the switch from the cold aisle and exhausts to the hot aisle.
•Identify the airflow designs of neighboring devices, and prevent hot air flowing out of the
neighboring device from entering the device.
•The rack is sturdy enough to support the switch and its accessories.
•The rack or workbench is reliably grounded.
To ensure correct operation and long service life of your switch, install it in an environment that meets
the requirements described in the following subsections.
Temperature/humidity
Maintain temperature and humidity in the equipment room as described in "Appendix A Chassis
views and technical specifications."
•Lasting high relative humidity can cause poor insulation, electricity leakage, mechanical
property change of materials, and metal corrosion.
•Lasting low relative humidity can cause washer contraction and ESD and cause problems
including loose mounting screws and circuit failure.
•High temperature can accelerate the aging of insulation materials and significantly lower the
reliability and lifespan of the switch.
For the temperature and humidity requirements of different switch models, see "Technical
specifications."
Cleanliness
Dust buildup on the chassis might result in electrostatic adsorption, which causes poor contact of
metal components and contact points, especially when indoor relative humidity is low. In the worst
case, electrostatic adsorption can cause communication failure.

3
Table 2 Dust concentration limit in the equipment room
Substance Concentration limit (particles/m³)
Dust ≤3 x 104 (no visible dust on the tabletop over three days)
NOTE:
Dust diameter ≥5 μm
The equipment room must also meet limits on salts, acids, and sulfides to eliminate corrosion and
premature aging of components, as shown in Table 3.
Table 3 Harmful gas limits in the equipment room
Gas Maximum concentration (mg/m3)
SO20.2
H2S 0.006
NH30.05
Cl20.01
EMI
All electromagnetic interference (EMI) sources, from outside or inside of the switch and application
system, adversely affect the switch in the following ways:
•A conduction pattern of capacitance coupling.
•Inductance coupling.
•Electromagnetic wave radiation.
•Common impedance (including the grounding system) coupling.
To prevent EMI, use the following guidelines:
•If AC power is used, use a single-phase three-wire power receptacle with protection earth (PE)
to filter interference from the power grid.
•Keep the switch far away from radio transmitting stations, radar stations, and high-frequency
devices.
•Use electromagnetic shielding, for example, shielded interface cables, when necessary.
•To prevent signal ports from getting damaged by overvoltage or overcurrent caused by lightning
strikes, route interface cables only indoors.
Laser safety
WARNING!
The switch is class 1 laser device. Do not stare into any fiber port when the switch has power. The
laser light emitted from the optical fiber might hurt your eyes.
Installation tools
•Flat-blade screwdriver
•Phillips screwdriver

4
•ESD wrist strap
All these installation tools are user supplied.
Installation accessories
All the installation accessories except M6 screws and floating nuts, the HPE X721 power to port fan
tray, PSR150-A/PSR150-A1 (JD362A/JD362B), and the PSR150-D/PSR150-D1 (JD366A/JD366B)
DC power supplies are provided with the switch.
Table 4 Installation accessories
Product
code Description Quantity Applicable models
5066-0850
1 U four-hole mounting bracket kit
(including one pair of mounting
brackets and eight M4 countersunk
screws)
1 kit All HPE 5130 HI switches
5190-0297
Rear mounting bracket kit
(including one pair of mounting
brackets and two load-bearing
screws)
1 kit
•HPE 5130 24G PoE+ 4SFP+ 1-slot
HI
•HPE 5130 48G PoE+ 4SFP+ 1-slot
HI
N/A
M6 screw and floating nut (user
supplied)
As required All HPE 5130 HI switches
5185-9292
Grounding cable (tin-plated at one
end and with a ring terminal at the
other end)
1
•HPE 5130 24G 4SFP+ 1-slot HI
•HPE 5130 48G 4SFP+ 1-slot HI
5185-9408
Grounding cable (with ring
terminals at both ends)
1
•HPE 5130 24G PoE+ 4SFP+ 1-slot
HI
•HPE 5130 48G PoE+ 4SFP+ 1-slot
HI
5185-8503
Power supply filler panel
1
•HPE 5130 24G 4SFP+ 1-slot HI
•HPE 5130 48G 4SFP+ 1-slot HI
5190-1774 Power supply filler panel 1
•HPE 5130 24G PoE+ 4SFP+ 1-slot
HI
•HPE 5130 48G PoE+ 4SFP+ 1-slot

5
Product
code Description Quantity Applicable models
HI
5190-0296
Interface card filler panel
1 All HPE 5130 HI switches
5060-0174
HPE X722 port to power fan tray
(already installed on the switch)
2 All HPE 5130 HI switches
5060-0175
HPE X721 power to port fan tray
(order as required)
2 All HPE 5130 HI switches
5185-9443
5080-0120
DC power cord (supplied with the
PSR150-D/PSR150-D1
(JD366A/JD366B)DC power
supply)
The power cord color code scheme
is for illustration only. The cable
delivered for your country or region
might use a different color scheme.
1
PSR150-D/PSR150-D1PSR150-D/PSR
150-D1(JD366A/JD366B) DC power
supply
5184-6719
Console cable
1 All HPE 5130 HI switches
5184-7298
Rubber feet
4 All HPE 5130 HI switches

6
Installing the switch
CAUTION:
Keep the tamper-proof seal on a mounting screw on the chassis cover intact, and if you want to open
the chassis, contact HPE for permission. Otherwise, HPE shall not be liable for any consequence.
Figure 1 Hardware installation flow
Ground the switch
Install the switch
Start
Connect power cords
Verify the installation
Turn on the circuit breaker
Select and install power
supplies
Hot-swap power
supplies?
Yes
No
Operating correctly? Turn off the circuit
breaker
Troubleshoot the switch
No
Yes
Hot-swap cards?
Install interface cards
Yes
Troubleshoot the switch
Yes
No
End
No
Operating correctly?
Install transceiver modules
and cables

7
Installing the switch in a 19-inch rack
Installation methods
Table 5 Installation methods for the HPE 5130 HI switches
Chassis Installation
methods Installation requirements Installation procedure
•HPE 5130 24G
4SFP+ 1-slot HI
•HPE 5130 48G
4SFP+ 1-slot HI
Using front
mounting
brackets
The mounting bracket kit can be
installed on the port side, power supply
side, or the mid-mounting position.
See "Rack-mounting by
using front mounting
brackets."
•HPE 5130 24G
PoE+ 4SFP+
1-slot HI
•HPE 5130 48G
PoE+ 4SFP+
1-slot HI
Using front
mounting
brackets
The front mounting bracket kit must be
installed on the mid-mounting position.
See "Rack-mounting by
using front mounting
brackets."
Using front and
rear mounting
brackets
•The mounting bracket kit can be
installed on the port side or power
supply side.
•Install the rear mounting brackets
according to the rack depth.
{If the rack depth is in the
range of 429 to 595 mm
(16.89 to 23.43 in), orient the
bracket with the wide flange
inside the rack.
{If the rack depth is in the
range of 274 to 440 mm
(10.79 to 17.32 in) and the
distance from the rear rack
posts to the inner surface of
the cabinet door is longer than
153 mm (6.02 in), orient the
bracket with the wide flange
outside the rack.
See "Rack-mounting by
using front and rear
mounting brackets
(HPE 5130 24G PoE+
4SFP+ 1-slot HI and
HPE 5130 48G PoE+
4SFP+ 1-slot HI)."
Figure 2 Rack-mounting procedure by using the front mounting brackets
Figure 3 Rack-mounting procedure by using the front and rear mounting brackets
NOTE:
If a rack shelf is available, you can put the switch on the rack shelf, slide the switch to an appropriate
location, and attach the switch to the rack by using the mounting brackets.

8
Mounting bracket kits
Table 6 Mounting bracket kits for the HPE 5130 HI switches
Mounting bracket
kits
HPE 5130 24G 4SFP+ 1-slot
HI
HPE 5130 48G 4SFP+ 1-slot
HI
HPE 5130 24G PoE+ 4SFP+ 1-slot
HI
HPE 5130 48G PoE+ 4SFP+ 1-slot
HI
Front mounting bracket
kit Provided Provided
Rear mounting bracket
kit Not required Provided
Grounding cable Provided Provided
Figure 4 Front mounting bracket kit
(1) Hole for attaching the bracket to the switch
chassis
(2) Hole for attaching the bracket to a rack
Figure 5 Rear mounting bracket kit
(1) Hole for attaching the bracket to a rack (2) Load-bearing screw
Rack-mounting by using front mounting brackets
This task requires two people.

9
To install the switch in a 19-inch rack by using the front mounting brackets:
1. Wear an ESD wrist strap and make sure it makes good skin contact and is reliably grounded.
2. Determine the mounting position on the switch for the front mounting brackets.
You can install the front mounting brackets at one of the following positions:
{HPE 5130 24G 4SFP+ 1-slot HI and HPE 5130 48G 4SFP+ 1-slot HI switches—Port side,
power supply side, or mid-mounting position.
{HPE 5130 24G PoE+ 4SFP+ 1-slot HI and HPE 5130 48G PoE+ 4SFP+ 1-slot HI
switches—Mid-mounting position.
3. Attach the front mounting brackets to the chassis:
a. Unpack the front mounting brackets and the M4 screws (supplied with the switch) for
attaching the brackets to the switch chassis.
b. Align the round holes in the wide flange of one front mounting bracket with the screw holes
in the chassis.
c. Use M4 screws to attach the mounting bracket to the chassis.
d. Repeat the proceeding two steps to attach the other mounting bracket to the chassis.
Figure 6 Attaching the front mounting bracket to the port side
Figure 7 Attaching the front mounting bracket to the power supply side

10
Figure 8 Attaching the front mounting bracket to the mid-mounting position
4. Mount the chassis in the rack:
a. One person supports the chassis bottom with one hand, holds the front part of the chassis
with the other hand, and pushes the chassis into the rack gently
b. The other person uses M6 screws and cage nuts (user supplied) to attach the switch to the
rack.
Figure 9 Mounting the switch in the rack (front mounting brackets at the port side)

11
Figure 10 Mounting the switch in the rack (front mounting brackets at the power supply
side)
Figure 11 Mounting the switch in the rack (front mounting brackets at the mid-mounting
position)

12
Rack-mounting by using front and rear mounting brackets
(HPE 5130 24G PoE+ 4SFP+ 1-slot HI and HPE 5130 48G
PoE+ 4SFP+ 1-slot HI)
This mounting method is applicable only to the HPE 5130 24G PoE+ 4SFP+ 1-slot HI and HPE 5130
48G PoE+ 4SFP+ 1-slot HI switches. You can install the front mounting brackets at the port-side or
power-side mounting position as needed. The following takes port-side mounting as an example.
The power-side mounting is similar.
This task requires two people.
To install the switch in a 19-inch rack by using the front and rear mounting brackets:
1. Wear an ESD wrist strap and make sure it makes good skin contact and is reliably grounded.
2. Attach the front mounting brackets and load-bearing screws to the chassis:
a. Unpack the front mounting brackets and the M4 screws for attaching the brackets to the
switch chassis.
b. Align the round holes in the wide flange of one front mounting bracket with the screw holes
in the port-side mounting position on one side of the chassis (see Figure 12).
c. Use M4 screws (supplied with the switch) to attach the mounting bracket to the chassis.
d. Repeat the proceeding two steps to attach the other mounting bracket to the chassis.
e. Unpack the load-bearing screws.
f. Install the load-bearing screws in one of the load-bearing screw mounting positions on both
sides of the chassis (see Figure 12).
Figure 12 Attaching the front mounting brackets and load-bearing screws to the chassis
3. Attach the rear mounting brackets to the rack:
a. Unpack the rear mounting brackets.
b. Install cage nuts (user-supplied) in the mounting holes in the rear rack posts.
c. Attach the rear mounting brackets to the rear posts with M6 screws (user supplied), as
shown in Figure 13 and Figure 14.
Do not fully tighten the M6 screws before mounting the switch in the rack.

13
Figure 13 Attaching the rear mounting brackets to the rack with the wide flange inside
the rack
Figure 14 Attaching the rear mounting brackets to the rack with the wide flange outside
the rack
4. Mount the switch chassis in the rack:
a. One person supports the chassis bottom with one hand, holds the front part of the chassis
with the other hand, and pushes the chassis into the rack gently.
Make sure the load-bearing screws closely contact with the upper edges of the rear
mounting brackets, as shown in Figure 15 and Figure 16.


14
b. The other person aligns the oval holes in the front brackets with the mounting holes in the
front rack posts, and attaches the front mounting brackets with M6 screws (user supplied) to
the front rack posts.
Tighten the screws and make sure the front and rear mounting brackets have securely
attached the switch to the rack.
Figure 15 Mounting the switch in the rack (with the wide flange of the mounting brackets
inside the rack)
Figure 16 Mounting the switch in the rack (with the wide flange of the mounting brackets
outside the rack)

15
Mounting the switch on a workbench
IMPORTANT:
•Ensure good ventilation and 10 cm (3.9 in) of clearance around the chassis for heat dissipation.
•Avoid placing heavy objects on the switch.
To mount the switch on a workbench:
1. Verify that the workbench is sturdy and reliably grounded.
2. Place the switch with bottom up, and clean the round holes in the chassis bottom with dry cloth.
3. Attach the rubber feet to the four round holes in the chassis bottom.
4. Place the switch with upside up on the workbench.
Grounding the switch
WARNING!
Correctly connecting the switch grounding cable is crucial to lightning protection and EMI protection.
The power input end of the switch has a noise filter, whose central ground is directly connected to the
chassis to form the chassis ground (commonly known as PGND). You must securely connect this
chassis ground to the earth so the faradism and leakage electricity can be safely released to the
earth to minimize EMI susceptibility of the switch.
You can ground the switch in one of the following ways, depending on the grounding conditions
available at the installation site:
•Grounding the switch with a grounding strip
•Grounding the switch with a grounding conductor buried in the earth ground
•Grounding the switch by using the AC power cord
NOTE:
The power and grounding terminals in this section are for illustration only.
Grounding the switch with a grounding strip
WARNING!
Connect the grounding cable to the grounding system in the equipment room. Do not connect it to a
fire main or lightning rod.
If a grounding strip is available at the installation site, connect the grounding cable from the chassis
to the grounding strip.
Connecting the grounding cable to the chassis
1. Remove the grounding screw from the rear panel of the switch chassis.
2. Use the grounding screw to attach the ring terminal of the grounding cable to the grounding
screw hole.
3. Verify that the grounding cable has been securely connected to the rear grounding point.

16
Figure 17 Connecting the grounding cable to the chassis
(1) Grounding screw (2) Ring terminal
(3) Grounding sign (4) Grounding hole
(5) Grounding cable
Connecting the grounding cable to a grounding strip (for the HPE 5130 24G PoE+ 4SFP+
1-slot HI and HPE 5130 48G PoE+ 4SFP+ 1-slot HI switches)
1. Remove the hex nut of a grounding post on the grounding strip.
2. Cut the grounding cable to a length required for connecting to the grounding strip.
3. Attach a ring terminal to the grounding cable:
a. Use a wire stripper to strip 5 mm (0.20 in) of insulation off the end of the grounding cable.
b. Slide the heat-shrink tubing onto the cable and insert the bare metal part into the end of the
ring terminal.
c. Use a crimper to secure the metal part of the cable to the ring terminal.
d. Slide the heat-shrink tubing down the cable until the tube covers the joint.
e. Use a heat gun to shrink the tubing around the cable.
Figure 18 Attaching a ring terminal to the grounding cable
4. Connect the ring terminal to the grounding post of the grounding strip, and fasten it with the
removed hex nut.