HUANUO HNCM1 User manual

Monitor Table Stand Instruction
Manual
Model: HNCM1
6
Thank you for choosing this HUANUO product! At HUANUO
we strive to provide you with the best quality products and
services in the industry. Please share your experience of our
product with others at www.huanuoav.com/reviews if you
are satisfied. Should you have any issues, please don't
hesitate to contact us.
Technical Support:
1-800-556-0533 Mon-Fri 10am - 5pm (PST) (USA) (CAN)
Other Info:
[email protected] (US/CA)
Website:
www.huanuoav.com

Supplied Parts and Hardware
X1
05 X4 06
• Please read through these instructions completely before attempting installation. If you do
not understand the instructions or have any concerns or questions, please contact
customer service at [email protected]
• Check package contents against Supplied Parts and Hardware List to assure that all
components were received undamaged. Do not use damaged or defective parts. If you
require replacement parts, contact customer service at [email protected]
• Not all parts and hardware included will be used.
• Do not use this product for any purpose or in any configuration not explicitly specified in
this instruction. We hereby disclaim any liability for injury or damage arising from incorrect
assembly, incorrect mounting, or incorrect use of this product.
IMPORTANT SAFTY INFORMATION
X1
01
X1
08
X1
07
Check the VESA Pattern of Monitor Before the Installation
Tools Required [Not Included]
If your TV VESA is greater than 100x100 mm/4 x 4 in. or less than VESA 75 x 75mm/3 x 3 in.,
this mount is NOT compatible.
If this mount is NOT compatible, please contact customer service at
[email protected] to find a compatible mount.
Minimum VESA Pattern: 3 in./75mm(W) x 3 in./75mm(H)
MAX:
100
mm/4 in.
MAX:
100
mm/4in.
100 mm ≈ 4 in.
75 mm ≈ 3 in.
Support Pillar X1
02
Base X1
03
Monitor Connector X2
04
Monitor Plate
Cable Clip Cable Clip Knob Grommet Plate
07060504030201
Drill(Optional)
Screw Driver

Step 1 Connect the Support Pillar Assembly to the Desktop
01
02
08
01
02
A
C
Step 1-1 Secure the support pillar [01] to the base [02] using bolts [A] and
Allen key [C]
Step 1-2 Secure the support pillar [01] with base [02] to desktop using
grommet plate [08] and knob [07]
07 D
Note: If there isn’t a hole on your desk, you
can use a 0.47 in.-1.18 in.(12 mm-30mm)
drill to drill a hole. The drill is NOT included.
φ 3/8（10mm）
Bolt
M4x12mm
M-A X8
Bolt
M4x16mm
M-B X8
Bolt
M5x12mm
M-C X8
Bolt
M5x16mm
M-D X8
D5
Washer
M-E X8
Spacer
M-F X8
07060504030201
X1
C
4mm Allen Key
X1
D
6mm Allen Key
X3
A
Bolt M5x18mm
X2
B
Bolt
M3x8mm
Nut

Allen Key [D]
15/64 in.(6mm)
Step 2-1 Slide the cable clip [05] and monitor connector [03] in sequence to the support
pillar [01].
Step 2-2 Attach the cable clips [06] to the monitor connector [03], then secure the
monitor connector [03] to support pillar [01] using Allen key [D]
Step 2
06
Connect Cable Clip [05] and Monitor Connector [03] to the
Support Pillar [01]
D
05
03 01
03 01
07060504030201

M5M4
Only one bolt size fits your monitor.
Select Monitor Bolts
Step 3
04
M-A/M-C
M-E
(If Needed)
(If Needed)
(If Needed)
M-B/M-D
M-E
M-F
FLAT BACK MONITOR
(UNIVERSAL MONITOR PLATE)
CURVED BACK MONITOR
(UNIVERSAL MONITOR PLATE)
Attach the Monitor Plates [04] to the Monitors
Step 4
Bolt length: Verify adequate thread engagement with bolts or bolts/spacers
combination. We recommend thread engagement by at least 5 turns.
-Too short will not hold the monitor.
-Too long will damage the monitor.
07060504030201

Allen Key [D]
15/64 in.(6mm)
B
Step 5
Fix Tilt Angle of the Monitors
Step 6
Secure Monitors to the Stand and Secure Using Nuts and
Bolts [B]
D
B
07060504030201

Manage Cables
Step 7
Step 8
D15/64 in.(6mm)
5/32 in.(4mm)
Store Allen Keys into the Cable Clip
C
07060504030201

Features
360°
360°
180°
Tilt Tilt
Individual VESA plate height
adjustment helps monitors to be
perfectly aligned.
Note: Please make sure two arms are aligned and balanced.
D
07060504030201