HUANUO HNDS11 User manual

Model: HNDS11
Monitor Desk Mount
Instruction Manual V3.0
Thank you for choosing this HUANUO product! At HUANUO we
strive to provide you with the best quality products and services
in the industry. Please share your experience of our product with
others on www.huanuoav.com/reviews if you are satisfied.
Should you have any issues, please don't hesitate to contact us.
Technical Support:
1-800-556-0533 Mon-Fri 10am - 5pm (PST) (USA) (CAN)
Other Info:
[email protected] (US/CA)
Website:
www.huanuoav.com

Check the VESA Pattern of Your Monitor beforeYouBegin the Installation
Please carefully read all instructions before attempting installation. If you do not
understand the instructions or have any concerns or questions, please contact our
Technical Support line at 1-800-556-0533 or customer service at [email protected].
CAUTION: Avoid potential personal injuries and property damage!
• Do not use this product for any purpose that is not explicitly specified in this manual. Do
not exceed weight capacity. We are not liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.
• This product contains a high pressure gas spring, fire and percussion prohibited. Also it is
strictly prohibited to dismantle without professionals. Please return to the
manufacturer or hand over to professional agencies if the product is abandoned.
• The desk must be capable of supporting three times the weight of the total load (the
mount, the monitor and all accessories weight). Don't use the product on particle board.
IMPORTANT SAFETY INFORMATION
If this desk mount is NOT compatible, please contact customer service
at [email protected] to find a compatible product.
If your monitor VESA is greater than 100x100 mm/4x4 in. or less than
VESA 75x75mm/3x3in., this mount is NOT compatible.
01
Weight Restrictions
MAX:100
mm/4 in.
MAX:100
mm/4 in.
MAX:100
mm/4 in.
4.4-26.5 lbs.
(2-12 kg)
DO NOT exceed the maximum weight indicated.
This mounting system is intended for use only within
the maximum weights indicated. Use with products
heavier than the maximum weights indicated may
result in failure of the mount and its accessories,
causing possible damage or injury.
WARNING
If your monitor weighs more, this
mount is NOT compatible.
100 mm ≈ 4 in.
75 mm ≈ 3 in. Minimum VESA pattern:
75mm/3 in.(W)x75mm/3 in.(H)
Note:
For the thin PB desks or glass table tops, you will need our
Monitor Mount Reinforcement Plate HNDA1(ASIN:
B08CK24TCX ), which provides a better way to install your
monitor mount on a desktop through C clamp installation.
If your monitor does not have any mounting hole, you will need
our Universal VESA Bracket Kit HNMUA4(ASIN:B088CWY5Q3
)(Fits most monitors within the size of 32 in.)

02
Product Features
180°
360°
360°
C-Clamp Mounting
1.0-3.2 in.(25-80mm)
Grommet Mounting
0.8-3.5 in.(20-90mm)

03
Warning!
Do not adjust tension without monitor.
1. Ensuremonitorhas been attached to the mount.
2. Read your monitor box or manual to find out monitor net weight.
3. Ensurethe net weight of monitor (including accessories) is between
4.4~26.5 Ibs (2-12 kg) per arm.
Clockwise to reduce
tension(carry less weight)
Counter-clockwise to increase
tension(carry more weight)
TENSION ADJUSTMENT SHOULD BE DONE ONLY
AFTER MOUNT INSTALLATION
Adjustment Sign

04
Supplied Parts and Hardware for Step 1
Supplied Parts and Hardware
Warning: This product contains small items that could be a choking hazard if
swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not
use damaged or defective parts. lf you require replacement parts, contact our
Product Support line at 1-800-556-0533 or customer service at
[email protected].
• Please note: Not all hardware included in this package will be used.
(F) x1
5/32 in.(4mm)
Medium Allen Key
(D)
Grommet Bolt x1
(E)
Locking Plate x1
Tools Needed (Not lncluded)
Phillips Screwdriver
M6x12mm (4pcs)
Bolt (C)
06 Cable Clip X204 C-Clamp X105 Pole Assembly X1
(D)
Butterfly Nut x1
Electric Drill
(Optional)
Drill Bit
(Optional)
0.4 in.(10mm) - 2 in.(50mm)

05
(F) x1
1/8 in.(3mm)
Small Allen Key
(F) x1
5/32 in.(4mm)
Medium Allen Key
13/64 in.(5mm)
Large Allen Key
(F)
04
02 Extension Arm x2 07 Locating Ring X2
Supplied Parts and Hardware for Step 2
Supplied Parts and Hardware for Step 3
Supplied Hardware for Step 4 and Step 6
Supplied Part for Step 8
Bolt (A)
M4x12mm (X8)Bolt (B-1)
M4x16mm (X8)
Spacer (B-2)
5mm (X8)
01 Arm X2
03 Cable Cover x1
(G)
Plastic Sleeve X2

06
1. Install the Base
A. For Clamp Mounting A-1 For Clamp Mounting
Warning:
Ensure bolts are
secured firmly.
Slide the cable clips [06] to pole
assembly [05] and secure part [a] to
pole assembly [05]
2
Detach the c-clamp entirely
1
F
5/32 in.(4mm)
Medium Allen Key
C
a
06
05
Connect part [b] to part [a] according to the thickness of the desktop
3
a
b
OR OR
a
b
a
b
a
b
F5/32 in.(4mm)
Medium Allen Key

07
Secure the pole assembly to the desktop
4
B. For Grommet Mounting
Warning:
Ensure bolt is
secured firmly.
D
05
Install the grommet bolt [D] to the bottom of pole assembly [05]
1
1.0-3.1 in.
（25-80mm）
F5/32 in.(4mm)
Medium Allen Key

08
D
E
Warning:
Ensure bolts are
secured firmly.
Secure the pole assembly to the desktop with grommet
2
Warning:
Ensure bolts are
secured firmly.
2. Install the Arms
①Fasten the locating ring [07] at your
desired height.
②Slide the extension arms [02] to the pole
assembly [05], and attach the plastic
sleeves [G] to extension arms [02]
07
07
07
G
05
G
02
(φ10-φ50mm)
φ0.4 - φ2 in.
0.8-3.5 in.
(20-90mm)
If there is no grommet hole on your desk,
position the pole assembly [05] on the
mounting surface and mark the hole. Drill a
hole using the drill bit in a diameter of 0.4
in.(10mm) - 2 in.(50mm) at the marked
position through the mounting surface.

09
Warning:
Ensure bolts are
secured firmly.
④Secure the arms [01] to the extension
arms [02] by tightening the preassembled
set screw [S] using Allen key [F]
③Attach the arms [01] to the extension
arms [02]
S
01
02
F
1/8 in.
(3mm)
Warning:
Ensure bolts are
secured firmly.
For VESA hole pattern:
3 in. (75mm) x 3 in. (75mm)
4 in. (100mm) x 4 in. (100mm)
Step 3 Attach Monitors to the Arms
3-1 Choose Proper bolts 3-2 Install Monitors to the Arms
10.1-0.2in.(3-5mm) spacing left
The tension is preset at
8.8~11 Ibs(4-5kg). After
hanging the monitor to
the mount, please
release the
monitor slowly to
prevent it from falling
suddenly.
100x100mm
75x75mm
A
Phillips
Screwdriver
[Not Included]
Flat back monitor
Round back monitor
100x100mm
75x75mm
B-1
B-2
Small Allen Key