HUANUO HNCM17 User manual

Monitor Desk Mount Instruction Manual
V2.0
Model: HNCM17
Thank you for choosing this HUANUO product! At HUANUO
we strive to provide you with the best quality products and
services in the industry. Please share your experience of our
product with others at www.huanuoav.com/reviews if you
are satisfied. Should you have any issues, please don't
hesitate to contact us.
Technical Support:
1-800-556-0533 Mon-Fri 10am - 5pm (PST) (USA) (CAN)
Other Info:
[email protected] (US/CA)
Website:
www.huanuoav.com

IMPORTANT SAFETY INSTRUCTIONS
•Check package contents against Supplied Parts and Hardware List to assure that all
components were received undamaged. Do not use damaged or defective parts. lf you
require replacement parts, contact customer service at [email protected]
•Carefully read all instructions before attempting installation. If you do not understand the
instructions or have any concerns or questions, please contact customer service at
[email protected]
•This product may contain moving parts. Use with caution.
•Do not use this product for any purpose that is not explicitly specified in this manual. Do not
exceed weight capacity. We cannot be liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.
• The desk must be capable of supporting five times the weight of the total load (the
mount, the monitor and all accessories weight). Don't use the product on particle board.
Check the VESA Pattern of Your Monitor beforeYouBegin the
Installation
If this desk mount is NOT compatible, please contact customer service
at [email protected] to find a compatible product.
If your Monitor VESA is greater than 100x100 mm/4x4 in. or less than
VESA 75x75mm/3x3in., this mount is NOT compatible.
75 mm ≈ 3 in.
100 mm ≈ 4 in.
Minimum VESA pattern:
75mm/3 in.(W)x75mm/3 in.(H)
MAX:100
mm/4 in.
MAX:100
mm/4 in.
MAX:100
mm/4 in.
Tool Need（Not Included）
Drill(Optional) 1/2 in.(13mm) - 1 in.(25mm)
Drill Bit(Optional)
Phillips Screwdriver
Weight Restrictions
DO NOT exceed the maximum weight indicated.This mounting
system is intended for use only within the maximum weights
indicated. Use with products heavier than the maximum weights
indicated may result in failure of the mount and its accessories,
causing possible damage and or injury.
WARNING
22.05 lbs.
(10 kg)
If your monitor weighs
more, this mount is NOT
compatible.
01 02 03 04 05 06 07

Large Allen Key
o (x1) Wire Clip n1 (x1) Wire Clip n2 (x6)
Supplied Parts and Hardware for Step 2
VESA Plate
e (x3) M4x12mm Thumb Bolt q (x8) M4 Spacer s (x8)
M4x30mm Bolt
r (x8)
Laptop Tray
t (x1)
M4x10mm Bolt
u (x4) M4 Nut v (x4)
Supplied Parts and Hardware for Step 3
Warning: This product contains small items that could be a choking hazard if swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not use damaged or
defective parts. lf you require replacement parts, contact our Product Support line at
1-800-556-0533 or customer service at [email protected].
• Please note: Not all hardware included in this package will be used.
Supplied Parts and Hardware
Pole
a (x1) C Clamp Plate b (x1) C Clamp Plate c (x1) M5x16mm Bolt
f (x3) M8x12mm Bolt
g (x2)
Medium Allen Key
o (x1) Small Allen Key o (x1) Bottom Pad w2 (x1)
Grommet Plate
m (x1)
Locking Plate
j (x1) Spring Washer l (x1)
M10 Washer
k (x1)
Supplied Parts and Hardware for Step 1
Bottom Pad
w1 (x1)
Swivel Arm
d (x1)
01 02 03 04 05 06 07

Step 1 Install the Pole to the Desktop
Option A: Desk Clamp Assembly
1A-1
1A-2
Nut
h (x3)
Supplied Hardware for Step 4
Supplied Hardware for Step 5
Medium Allen Key
o (x1)
c
b
g
o
Medium
Allen Key
OR
b
Plastic Knob
a
c
f
w1
o
Small Allen Key
01 02 03 04 05 06 07

Step 2 Install Swivel Arms to the Pole
Option B: Grommet Base Assembly
1. If the existing grommet hole comes with a plastic protector, remove it to ensure
a flat surface before installing the desk mount.
2. If there is no grommet hole on your desk, position the Pole (a) on the mounting
surface and mark the hole. Drill a hole at the marked position through the mounting
surface.
Note:
a
f
m
w2
o
Small Allen Key
Install swivel arms (d) to the pole (a). Fasten the bolt with supplied Allen key (o).
Attach the wire clip (n1,n2) to the pole (a) and swivel arms (d).
d
o
n1
n2
d
UP
01 02 03 04 05 06 07
j
k
l
Phillips Screwdriver

Step 3 Attach the VESA Plate to the Laptop Tray or Monitor
For Laptop
For Monitor with Flat Back
For Monitor with Curved
or Recessed Back
q
r
s
e
t
u
v
01 02 03 04 05 06 07

Step 4 Secure the Monitor or Laptop Tray onto the Head of Swivel
Arm
h
4-1 Slide the monitor onto the head of
Swivel Arm (d) as shown in the above
diagram.
4-2 Secure the Nut (h). Make sure the nut
is installed before you rotate the monitor.
HEAVY! You may need
assistance with this step.
Step 5 Adjust the Tilt and Swivel Angle
1. Slightly loosen the bolt [S] on the swivel
arm.
2. Swivel your monitor or laptop to your desred
position.
3. Retighten bolt [S] to hold monitor or laptop
in place.
Swivel Adjustment
T
o
Medium
Allen Key
Tilt Adjustment
1. Slightly loosen the bolt [T] on the swivel
arm.
2. Tilt your monitor or laptop.
3. Retighten bolt [T] to hold monitor or laptop
in place.
o
Medium
Allen Key
01 02 03 04 05 06 07

Step 6 Manage the Wires and Store the Allen Keys on Wire Clip
01 02 03 04 05 06 07