HUANUO HNCM3 User manual

Installation Instruction V2.0
HNCM3 [email protected]

1
UNPACKING INSTRUCTIONS
Carefully open the carton, remove contents and lay out on cardboard or other protective
surface to avoid damage.
Check package contents against the Supplied Parts List in the next page to assure that
all components were received undamaged. Do not use damaged or defective parts.
Carefully read all instructions before attempting installation.
IMPORTANT SAFETY INFORMATION
Install and operate this device with care. Please read this instruction before installation,
and carefully follow all instructions contained herein. Use proper safety equipment during
installation.
Please call a qualified installation contractor for help if you don't understand these
directions or have any doubts about the safety of the installation.
Do not use this product for any purpose or in any configuration not explicitly specified in this
instruction. We hereby disclaims any and all liability for injury or damage arising from
incorrect assembly, incorrect mounting, or incorrect use of this product.
!
!
!
!
!

2
Supplied Parts List
Not Included Phillips Screwdriver
“C” Clamp Brace
c (x1)
Nut
f1 (x2)
M10 Bolt
i (x1)
Grommet Base Plate
m (x1)
Wrench
p (x1)
“C” Clamp
b (x1)
VESA Plate
e2 (x1)
M8x12 Bolt
h (x2)
Spring Washer
l (x1)
Allen Key
o (x1)
M4 Spacer
s (x12)
Pole
a (x1)
VESA Plate
e1 (x2)
M5x14 Bolt
g (x3)
M10 Washer
k (x1)
Wire Clip
n2 (x4)
M4x30 Bolt
r (x12)
Swivel Arm
d (x1)
M4x6 Bolt
f2 (x1)
Support Plate
j (x1)
Wire Clip
n1 (x1)
M4x12 Thumb Bolt
q (x12)

3
Step 1 Install the Pole to the Desktop
Option B: Grommet Base Assembly
Option A：Desk Clamp Assembly a
Figure 1
gc
Figure 2
h
o
b
Plastic Knob
1. Use 3 pieces M5x14 bolts(g) to install the C Clamp
brace(c) to the Pole. Use the Allen Key(o) to tighten
the bolts. See Figure 1.
2. According to the thickness of the desktop, Use 2
pieces M8x12 bolts(h) to install the C clamp(b) to C
clamp brace (c). Use Allen Key(o) to tighten the bolts
and then tighten the C clamp to the desktop by
adjusting the plastic knob. See Figure 2.
Existing Grommet Hole Installation
If the existing grommet hole comes with a plastic
protector, remove it to ensure a flat surface
before installing the desk mount.
1. Use 3 pieces M5x14 bolts(g) to install
Grommet Base Plate(m) to the Pole(a). Use the
Allen Key to tighten the bolts. See Figure 3.
2. Position the Pole(a) on the mounting surface
and under the desktop comes the Support Plate
(j), M10 Washer(k), Spring Washer (l). Use the
provided Wrench(p) to fasten the M10 Bolt. See
Figure 4.
o
o
Figure 4
j
i
p
k
l
a
Figure 3
m
g

4
Step 1 Install the Pole to the Desktop
Step 2 Install Arm to the Pole
Option B: Grommet Base Assembly a
Figure 5
Figure 6
m
g
o
Existing Grommet Hole Installation
1. Position the Pole(a) on the mounting surface
and mark the center hole. Drill a 3/8" (10mm)
diameter hole at the marked position through the
mounting surface.
2. Use 3 pieces M5x14 Bolts(g) to install the
Grommet Base Plate(m) to the Pole(a). Use the
Allen Key(o) to tighten the bolts. See Figure 5.
3. Position the Pole(a) on the mounting surface
and under the desktop comes the Support Plate
(j), M10 Washer(k), Spring Washer (l). Use the
provided Wrench(p) to fasten the M10 Bolt. See
Figure 6.
Install Swivel Arm(d) to the Pole(a). Fasten the
bolt with supplied Allen Key(o). Attach the Wire
Clip(n1,n2) to the Pole(a) and Swivel Arm(d).
j
i
p
k
l
d
o
n1
n2

5
Step 3A Attach the Side VESA Plates to the Monitors
Attach the Center VESA Plate to the Monitor
For Monitor with Flat Back For Monitor with Curved
or Recessed Back
For Monitor with Flat Back For Monitor with Curved
or Recessed Back
qs
r
e1
e1
Step 3B
q
s
r
e2 e2

6
Step 4A Slide the Side Monitors onto the Head of Swivel Arm
Step 4B Slide the Center Monitor onto the Head of Monitor Arm
Slide the monitor onto the head of Swivel Arm
(d) as shown in the above diagram.
Slide the monitor onto the head of Monitor
Arm(d) as shown in the above diagram.
Install the M4x6 Bolt(f2). Make sure the bolt is
installed before you rotate the monitor.
Install the security Nut(f1). Make sure the
security nut is installed before you rotate the
monitor.
f1
d
f2
d

7
Step 5 Fix the Tilt Angle of Side and Center Monitors
Step 6 Adjust the Horizontal Level of Monitors
Tighten the bolt with the supplied Allen Key(o) to
fix the tilt angle.
Adjust the heigh of Centre Monitor: Turn
the bolt counterclockwise to lower the center
monitor, turn the bolt clockwise to raise the
center monitor.
Adjust the height of Side Monitors: Remove
the Nut(f1) and turn the bolt counter-clockwise
with supplied Allen key(o) to raise the monitor.
Install the Nut(f1) after the adjustment.
Fasten the grub screw in monitor arm to fix the
tilting angle by provided Allen Key(o).
o
o
Fix the tilt angle Fix the tilt angle
grub
screw
o
o

8
Step 7 Fix the Tilt Angle of Side and Center Monitors
Step 8 All Done
n1
Manage the wires and store the Allen keys(o) in Wire Clip(n1) for future use.
0-100mm(0-4inch)
78mm(3.1inch)
93mm(3.7inch)
450mm(17.8inch)
1220mm(48inch)
75-100mm(3-4inch)
75-100mm(3-4inch)

Thank you for choosing our product! We strive to provide the best quality
and services for our customers. Would you kindly share your experience
on Amazon if you are satisfied? Should you have any issues, please don't
hesitate to contact us.
Telephone：[phone]
Mon-Fri 10am - 6pm (PST) (USA)
Email：[email protected]
(US/CA/DE/UK/FR/IT/ES/JP/AU)