Huawei HG532D User manual

Quick Setup Guide
Huawei HG532d

Headline
Getting Connected
1Modem Setup
2Line Filter & Phone Setup
3Wait for DSL Activation
4WiFi Setup
5Advanced Modem Setup (if required)
6Contact Support
7Other Details
WE’VE GOT YOU COVERED
For your convenience, the iiNet Support Team has preconfigured this modem with your
broadband account details.
This guide will get you up and running in just a few simple steps.
For manual setup instructions, please skip to step 5: Advanced Modem Setup.

Headline
1. Modem Setup
Wall Socket
Power Point
DSL Port
Ethernet
Power
PC
ADS LL AN AN AN
1. With the supplied Power cable, connect the Power port on the back of your modem to your power point.
2. With the supplied Ethernet cable, connect your PC to any of the 4 LAN ports on the back of your modem.
3. With the supplied RJ-11 telephone cable, connect the ADSL port on the back of your modem to your telephone wall socket.
(See next page if you have a telephone connected to the same wall socket as your modem)
1
2
3

Every device connected to the phone line except for the modem must have an ADSL line filter attached.
Examples of devices that must be connected to the phone line through an ADSL line filter are:
•Telephone Handset •Fax Machine •Foxtel Digital box •Back to base alarm •Dial up modem •EFTPOS terminal
A Central splitter should be installed by a licensed technician if you’re connecting to 3 or more devices, or
a monitored alarm system.
Modem and phone share the same wall socket
Scenario A: 1 Wall Socket
If you wish to connect the modem and phone separately
Scenario B: 2 Wall Sockets
Wall Socket
Telephone
Phone jack
ADSL jack
ADSL Fliter
ADSL Fliter
DSL Port
DSL Port
Modem
Phone
Wall Socket Wall Socket
Telephone
Phone jack
Modem
2. Line Filter & Phone Setup
Phone
ADSL ADSL

Headline
3. Wait for DSL Activation
When your iiNet broadband connection is
up and running, the ADSL light in the front
of your modem will become solid green.
We’ll send you an email and SMS once
your broadband is active on our end but
it’s perfectly fine to set your modem up in
advance.
If you’d like to check up on the progress of
your connection, please give us a call on the
appropriate number in section 6: Contact
Support.

Headline
READY RIGHT OUT OF THE BOX
Your modem has been pre-configured for WiFi; your WiFi password is the same as your
broadband password
1. Make sure that wireless/WiFi is enabled on your computer, smartphone or other devices.
2. Your modem’s unique WiFi network name is printed on a sticker underneath your modem. Using your wireless device, scan
for available WiFi networks and select the network called TPG-xxxx (xxxx is a random 4 digit alphanumeric code).
3. Enter the Security Key (WiFi password). By default, this is the same as your broadband password.
4. WiFi Setup

Headline
SUPPORT INFORMATION
5. Advanced Modem Setup
PLEASE NOTE
Your modem has been pre-configured, so you
don’t need to set up manually unless you’re a
tech whiz who really wants to.
If you’re just looking to change your WiFi network name and/or
password, skip to section 3: Configuring Modem.
Contents
1. Physical Connection
2. Network Configuration
3. Configuring Modem
4. Connecting to Wireless
5. Change of Password

2. Network Configuration
PPPoE connection does not require you to have an IP address or DNS settings manually encoded on your network card.
PPPoE connection uses authentication to establish the Internet connection and once connected your modem will be
assigned an IP and DNS settings from us.
To begin, your PC needs to receive a private IP address from the modem. Most ADSL modems have DHCP enabled by
default that will take care of this.
To ensure your Network Card is ready for this, please follow the following steps:
a. Click Start > Settings > Control Panel > Network and Sharing Centre
and then click Change adapter settings.
b. Right click on Local Area or Ethernet Connection and select Properties
1. Physical Connection
Please refer to Section 1: Modem Setup.
Please have your modem turned ON and connected directly to your PC via Ethernet
cable before you begin as these instructions require a wired Ethernet connection.

Headline
2. Network Configuration (continued)
c. Double click on Internet Protocol TCP/IP
d. Ensure “Obtain an IP address automatically” is selected
e. Ensure “Obtain DNS server address automatically” is
selected
f. Click OK
For Windows Vista, you may use the search bar on the
Windows Menu to look for Local Area Connection.
3. Configuring Modem
a. Open your browser and type http://192.168.1.1 in the address bar
then press Enter
b. Enter admin for both the username and password and click Login.
If you have changed the login credentials, please enter the current
username and password for your router interface.
c.
d.
e.

Headline
3. Configuring Modem (continued)
c. You will see the screen as shown on the right.
d. Enter your broadband service username and password.
Click Next.
e. You can change your WiFi details or elect to keep the
default settings. The default WiFi SSID is printed on the
sticker underneath your modem. The WiFi password is
set to your broadband service password by default.
Click Next
f. Quick Setup complete.
e.
d.