Huawei SmartAX MA5608T User manual

SmartAX MA5608T
Quick Installation Guide
Issue: 03
Date: 2015-04-30
HUAWEI TECHNOLOGIES CO., LTD.

Contents
1 Precautions...............................................................................................................................................3
2 Check Tools and Meters .......................................................................................................................4
3 Outline and Structure.............................................................................................................................5
4 Installing the Chassis.............................................................................................................................6
4.1 Installation in a Cabinet or a Rack.................................................................................................................................6
4.2 Installation in the Network Cabinet of the Customer ...................................................................................................7
4.3 Guide for Grounding the Network Cabinet of the Customer ........................................................................................8
5 Routing Cables........................................................................................................................................9
5.1 Routing the PGND Cable and the External Power Cable..............................................................................................9
5.2 Routing Subscriber Cables ..........................................................................................................................................10
5.3 Routing Trunk Cables..................................................................................................................................................11
5.4 Routing Network Cables..............................................................................................................................................12
5.5 Routing Optical Fibers.................................................................................................................................................13
6 Checking the Installation....................................................................................................................14
7 Powering On the System.....................................................................................................................15
2Copyright © Huawei Technologies Co., Ltd. 2015. All rights reserved.

Precautions
Electrostatic Protection
Before touching the device, or holding the boards or IC chips, wear the ESD gloves or the ESD wrist strap (Ensure that the
other end of the ESD wrist strap is well grounded.) to prevent the electrostatic discharge of the human body from damaging
the sensitive components.
Bundling cables
lThe distance between cable ties inside the cabinet should be within 250 mm. (For subscriber cable, the distance is 200
mm.)
lThe distance between cable ties for all cables outside the cabinet is determined according to the distance between two
horizontal beams. For the cabling trough without beams, bundle the cables with the distance not exceeding 250 mm
between cable ties.
Affixing labels / tags
Affix the label or tag to the signal cable, 2 cm away from the connector. When the cable is placed vertically, the label or
tag should point towards the right. When the cable is placed horizontally, the label or tag should point downwards.
3

Check Tools and Meters
Before you begin, get the following tools ready.
Marker pen Flathead screwdriver Phillips screwdriver Diagonal pliers
Wire cutter Paper knife Adjustable wrench Mount bar
Tape measure Cable cutter
Network cable crimping
pliers Network cable tester
Multimeter Optical power meter ESD gloves ESD wrist strap
4

Outline and Structure
5

Installing the Chassis
4.1 Installation in a Cabinet or a Rack
6

Installing the Chassis
4.2 Installation in the Network Cabinet of the Customer
7

Installing the Chassis
4.3 Guide for Grounding the Network Cabinet of the Customer
8

Routing Cables
5.1 Routing the PGND Cable and the External Power Cable
9

Routing Cables
5.2 Routing Subscriber Cables
10

Routing Cables
5.3 Routing Trunk Cables
11

Routing Cables
5.4 Routing Network Cables
12

Routing Cables
5.5 Routing Optical Fibers
13

Checking the Installation
No. Description Method
1Do not place any materials on the chassis. Observe
2 All the cables are bound with proper tightness. The space between the cable ties is even, and the
remaining parts of the cable ties are cut off neatly. All cable ties face the same direction, keeping
the overall appearance nice.
Observe
3 The cross sectional area of the power cable and ground cable complies with the engineering design,
and satisfy the requirements of equipment running.
Observe
4 The power cable and ground cable adopt a whole segment of copper core. The cable has no
connection in the middle or scratch on the skin.
Observe
5 The power cable and ground cable must be routed horizontally and vertically without crossover.
Proper margins must be reserved at the turning.
Observe
6 The power cable and ground cable must be connected correctly and reliably. Observe
7 The identifiers on the power cable and ground cable must be correct, legible, and neat. Observe
8 The power cable, ground cable, and signal cables must be routed separately. Observe
9 Signal cables must be long enough, and must not be damaged or broken, without joint in the cable. Observe
10 The connectors of the signal cables must be neat and intact. The connectors must be connected
correctly and firmly. The tips must be connected securely.
Observe
11 Labels at both ends of the signal cables must be marked correctly, clearly and neatly. Observe
12 If the fibers must be routed outside the cabinet, protection measures must be taken, such as using
corrugated pipes or guide troughs.
Observe
13 Place the optical fiber pairs in order and bind them carefully with optical binders. No sharp edge
is allowed.
Observe
14

Powering On the System
15