Huawei TaiShan 200 User manual

123
TaiShan 200 Server Quick Installation Guide
(Model 2280) VF
Document Issue 02 (2023-02-30)
PN: 31500GYR (2/3)
Huawei Technologies Co., Ltd.
Copyright © Huawei Technologies Co., Ltd. 2023. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without
prior written consent of Huawei Technologies Co., Ltd.
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their
respective holders.
The purchased products, services and features are stipulated by the contract made between Huawei
and the customer. All or part of the products, services and features described in this document may
not be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all
statements, information, and recommendations in this document are provided "AS IS" without
warranties, guarantees or representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in
the preparation of this document to ensure accuracy of the contents, but all statements, information,
and recommendations in this document do not constitute a warranty of any kind, express or implied.
Symbol
Description
Indicates a hazard with a high level of risk which, if not avoided, will
result in death or serious injury.
Indicates a hazard with a medium level of risk which, if not avoided,
could result in death or serious injury.
Indicates a hazard with a low level of risk which, if not avoided, could
result in minor or moderate injury.
Indicates a potentially hazardous situation which, if not avoided, could
result in equipment damage, data loss, performance deterioration, or
unanticipated results.
NOTICE is used to address practices not related to personal injury.
Supplements the important information in the main text.
NOTE is used to address information not related to personal injury,
equipment damage, and environment deterioration.
1 Specifications
The TaiShan 200 server powered by Huawei Kunpeng 920 processors is dedicated for data centers. Its
2280 balanced model (TS-2280 for short) is a 2U 2-socket rack server.
Environmental specifications:
Item
Specification
Temperature
⚫Operating temperature: +5°C to +40°C (+41°F to +104°F)
(ASHRAE Classes A2 and A3 compliant)
⚫Storage temperature (within 3 months): –30°C to +60°C (–22°F
to +140°F)
⚫Storage temperature (within 6 months): –15°C to +45°C (+5°F to
+113°F)
⚫Storage temperature (within 1 year): -10°C to +35°C (14°F to
95°F)
⚫Maximum temperature change rate: 20°C (36°F) per hour, 5°C
(9°F) per 15 minutes
If a single fan fails, the server performance may be affected or a
temperature alarm may be generated. After the faulty fan is
replaced, the fault can be rectified.
Relative humidity (RH, no-
condensing)
⚫Operating humidity: 8% to 90%
⚫Storage humidity (within 3 months): 8% to 85%
⚫Storage humidity (within 6 months): 8% to 80%
⚫Storage humidity (within 1 year): 20% to 75%
⚫Maximum humidity change rate: 20% per hour
Maximum altitude
3050 m (10,000 ft.)
ASHRAE 2015 compliant:
⚫ASHRAE Classes A1 and A2 compliant: For altitudes above 900
m (2952.76 ft.), the highest operating temperature decreases by
1°C (1.8°F) for every increase of 300 m (984.25 ft.) in altitude.
⚫ASHRAE Class A3 compliant: For altitudes above 900 m (2952.76
ft.), the highest operating temperature decreases by 1°C (1.8°F)
for every increase of 175 m (574.15 ft.) in altitude.
⚫ASHRAE Class A4 compliant: For altitudes above 900 m (2952.76
ft.), the highest operating temperature decreases by 1°C (1.8°F)
for every increase of 125 m (410.10 ft) in altitude.
2 Tools
ESD gloves Floating nut mounting bar Phillips screwdriver Ladder
3 Installation
To obtain the operation guide, scan the QR code.
⚫Exercise caution when using tools.
⚫If the installation position of the device is higher than the shoulders of the installation personnel,
use a vehicle such as a lift to facilitate installation. Prevent the device from falling down and
causing personal injury or damage to the device. When a ladder is used, ensure that another
person holds the ladder steady to prevent accidents.
⚫Wear ESD gloves and remove conductive objects, such as jewelry and watches.
⚫At least two persons are required to move the chassis. When moving a chassis, keep your back
straight and move smoothly to avoid any injury
⚫Do not use mounting ears as the holding points when moving the server. Otherwise, the server
may be damaged or slipped.
1. Hold the bottom of the server with both hands, lift the server from both sides, and place the server
on the guide rails.
2. Push the server into the cabinet. See (1).
3. Align the mounting ears on both sides of the server with the mounting bars and tighten the
captive screws on the mounting ears to secure the server. See (2).
4 Power-On
The TS-2280 does not provide a separate ground port. It uses power cables for ground connection.
The device is powered by high-voltage power sources. Direct or indirect contact (especially through
damp objects) with high-voltage power sources may result in serious injury or death.
1. Connect the VGA cable , USB cables , FlexIO card cables , management network
port cable , and serial cable as required.

4 5 6
Port description:
Port
Silkscreen
Port on the Server
Cable
VGA port
USB port
FlexIO card
network port
Management
network port
Serial port
Power supply
unit (PSU)
socket
-
2. Connect cables to the PSU sockets.
3. Turn on the power switch in the cabinet.
The recommended current specification for the external power circuit breaker connected to the server
is as follows:
⚫AC power supply: 32 A
⚫DC power supply: 63 A
4. Power on the server.
The power-on methods of the server vary according to the following scenarios:
⚫The PSUs are properly installed but not powered on.
Connect the external power supply to the PSUs. Then the server will power on with the PSUs.
The default value of System State Upon Power Supply is Power on, which indicates that the server
automatically powers on after power is supplied to the PSUs. You can change the value on the iBMC
WebUI.
⚫The PSUs are installed properly and powered on. The server is in the standby state (the power
button/indicator is steady yellow).
−Press the power button/indicator to power on the server.
−Power on the server using the iBMC CLI.
Log in to the iBMC CLI, run the ipmcset -d powerstate -v 1 command, and enter yor Yto
power on the server.
−Power on the server using the iBMC WebUI.
Log in to the iBMC WebUI. Choose System > Power > Power Control, click the Power On
button, and click OK in the dialog box displayed.
−Power on the server using the remote virtual console.
Log in to the remote virtual console. On the KVM screen, click or on the toolbar,
select Power On, and click OK to power on the server.
5. Check the status of the indicators.
⚫If the PSU indicators are steady green, the PSUs are powered on.
⚫If the server power button/indicator is steady green, the server is powered on.
5 Follow-up Operations
After installing the server into the cabinet and powering it on, perform other necessary operations
such as configuring the server. For details, see the TaiShan 200 Server User Guide (Model 2280) VF
Scan the QR code to visit the Huawei technical support website.
Website: https://support.huawei.com/enterprise/en/
Under TECHNICAL SUPPORT, enter (model 2280) VF to search.
6 Appendix: Hazardous Substance Statement for
Electronic and Electrical Products
Part
Hazardous Substances
Cd
Pb
Hg
Cr (VI)
PBBs
PBDEs
PCBA
◯
╳
◯
◯
◯
◯
Cables
◯
╳
◯
◯
◯
◯
Accessories
◯
╳
◯
◯
◯
◯
Equipment
◯
╳
◯
◯
◯
◯
Batteries*
◯
╳
◯
◯
◯
◯
This statement for electronic and electrical products complies with SJ/T 11364.
◯: all homogenous part materials under GB/T 26572 hazardous substance limit
×: at least one homogenous material exceeds GB/T 26572 hazardous substance limit
*: when in use by the product