Huawei FusionModule2000 V500R003C10 User manual

FusionModule2000 Smart Modular Data Center
V500R002
Installation Guide (2000 mm
High Cabinets, Single-Row Aisle
Containment, 380 V)
Issue
04
Date
2017-06-30
HUAWEI TECHNOLOGIES CO., LTD.

Issue 04 (2017-06-30)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
i
Copyright © Huawei Technologies Co., Ltd. 2017. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior
written consent of Huawei Technologies Co., Ltd.
Trademarks and Permissions
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and
the customer. All or part of the products, services and features described in this document may not be
within the purchase scope or the usage scope. Unless otherwise specified in the contract, all statements,
information, and recommendations in this document are provided "AS IS" without warranties,guarantees or
representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Huawei Technologies Co., Ltd.
Address:
Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China
Website:
http://e.huawei.com

FusionModule2000 Smart Modular Data Center
Installation Guide (2000 mm High Cabinets, Single-Row
Aisle Containment, 380 V)
About This Document
Issue 04 (2017-06-30)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
ii
About This Document
Purpose
This document describes how to install the smart modular data center (Smart Module for short)
in the single-row aisle containment scenario.
Intended Audience
This document is intended for:
Hardware installation engineers
Commissioning engineers
Maintenance engineers
Technical support engineers
Symbol Conventions
The symbols that may be found in this document are defined as follows.
Symbol
Description
Indicates an imminently hazardous situation which, if
not avoided, will result in death or serious injury.
Indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
Indicates a potentially hazardous situation which, if not
avoided, may result in minor or moderate injury.
Indicates a potentially hazardous situation which, if not
avoided, could result in equipment damage, data loss,
performance deterioration, or unanticipated results.
NOTICE is used to address practices not related to
personal injury.

FusionModule2000 Smart Modular Data Center
Installation Guide (2000 mm High Cabinets, Single-Row
Aisle Containment, 380 V)
About This Document
Issue 04 (2017-06-30)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
iii
Symbol
Description
Calls attention to important information, best practices
and tips.
NOTE is used to address information not related to
personal injury, equipment damage, and environment
deterioration.
Change History
Changes between document issues are cumulative. The latest document issue contains all
updates made in previous issues.
Issue 04 (2017-06-30)
Optimized the description.
Issue 03 (2016-10-31)
Added the descriptions about how to install the base, access control system on the sliding door,
and the smart module in the scenario with a column.
Issue 02 (2016-08-30)
Updated the product name from IDS2000 to FusionModule2000.
Issue 01 (2016-06-07)
This issue is the first official release.

FusionModule2000 Smart Modular Data Center
Installation Guide (2000 mm High Cabinets, Single-Row
Aisle Containment, 380 V)
Contents
Issue 04 (2017-06-30)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
iv
Contents
About This Document ............................................................................................................ ii
1 Installation Preparations.......................................................................................................1
1.1 Precautions for Transportation.............................................................................................................................................1
1.2 Unpacking and Acceptance..................................................................................................................................................2
1.3 Installation Environment Requirements..............................................................................................................................3
1.4 Site Requirements.................................................................................................................................................................5
1.5 Documents.............................................................................................................................................................................6
1.6 Tools and Instruments...........................................................................................................................................................8
1.7 Tools Delivered with Equipment.......................................................................................................................................12
1.8 Personnel Requirements.....................................................................................................................................................14
1.9 Installation Process.............................................................................................................................................................15
2 Scenario Description ........................................................................................................... 16
3 Hardware Installation Preparations................................................................................... 18
3.1 Preparing for Installing Air Conditioners..........................................................................................................................18
3.1.1 Material Preparations.......................................................................................................................................................18
3.1.2 Preparing for Installing the NetCol5000-A 35 kW Air Conditioner ............................................................................18
3.1.2.1 (Optional) Refrigerant R410A.....................................................................................................................................18
3.1.2.2 Refrigerant Oil..............................................................................................................................................................20
3.1.2.3 Pipe Components..........................................................................................................................................................20
3.1.2.4 Humidifier Water Inlet Pipe, Pump Drainpipe, and Automatic Drainpipe ...............................................................21
3.1.2.5 Pipe Support..................................................................................................................................................................23
3.1.2.6 Preparing Cables...........................................................................................................................................................23
3.1.2.7 Checking the Air Pressure............................................................................................................................................24
3.1.2.8 Removing the Transport Fasteners from Floats..........................................................................................................26
3.1.2.9 Removing the Transport Fasteners from a Compressor.............................................................................................28
3.1.3 Preparing for Installing the NetCol5000-A 25 kW Air Conditioner ............................................................................29
3.1.3.1 (Optional) Refrigerant R410A.....................................................................................................................................29
3.1.3.2 (Optional) Refrigerant Oil............................................................................................................................................31
3.1.3.3 (Optional) Oil Trap and Inverted Trap ........................................................................................................................31
3.1.3.4 Humidifier Water Inlet Pipe.........................................................................................................................................32
3.1.3.5 Drainpipe.......................................................................................................................................................................33
3.1.3.6 Pipe Support..................................................................................................................................................................34

FusionModule2000 Smart Modular Data Center
Installation Guide (2000 mm High Cabinets, Single-Row
Aisle Containment, 380 V)
Contents
Issue 04 (2017-06-30)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
v
3.1.3.7 Preparing Cables...........................................................................................................................................................34
3.1.3.8 (Engineering Procurement) Water Softener................................................................................................................36
3.1.3.9 Checking Nitrogen Pressure ........................................................................................................................................37
3.1.3.10 Removing the Transport Fasteners............................................................................................................................38
3.2 Removing Pallets ................................................................................................................................................................41
3.2.1 Removing the PDC Pallet ...............................................................................................................................................41
3.2.2 Removing the IT Cabinet Pallet......................................................................................................................................44
3.2.3 Removing the NetCol5000-A 35 kW Air Conditioner Pallet .......................................................................................45
3.2.4 Removing the NetCol5000-A 25 kW Air Conditioner Pallet .......................................................................................45
3.3 (Optional) Adjusting IT Cabinet Side Plates.....................................................................................................................46
3.4 (Optional) Adjusting Battery Cabinet Side Plates ............................................................................................................47
3.5 (Optional) Installing the PDC Tail Frame.........................................................................................................................48
3.6 (Optional) Installing a 600 mm Wide Air Conditioner Enclosure Frame .......................................................................53
3.7 (Optional) Installing a 300 mm Wide Air Conditioner Enclosure Frame .......................................................................57
3.8 (Optional) Installing Bases.................................................................................................................................................58
3.8.1 Precautions for Installing the Base.................................................................................................................................58
3.8.2 Installing Adjustable Bases .............................................................................................................................................59
3.8.2.1 Installing a Cabinet Base..............................................................................................................................................59
3.8.2.1.1 Assembling a Base.....................................................................................................................................................59
3.8.2.1.2 Positioning Bases.......................................................................................................................................................61
3.8.2.1.3 Securing Bases...........................................................................................................................................................63
3.8.3 Installing Fixed-Size Bases.............................................................................................................................................65
3.8.3.1 Deploying a 300 mm Wide Air Conditioner Base......................................................................................................65
3.8.3.2 Deploying Bases for a 600 mm wide IT Cabinet/Battery Cabinet/Network Cabinet ..............................................67
3.8.3.3 Deploying Bases for a 600 mm Wide Air Conditioner and PDC ..............................................................................67
3.8.3.4 Deploying 800 mm Wide Fixed Bases........................................................................................................................70
3.8.3.5 Securing Bases..............................................................................................................................................................70
3.9 Installing Air Conditioner Outdoor Units and Routing Pipes ..........................................................................................72
4 Installing Cabinets .............................................................................................................. 74
4.1 Installing Cabinets (with Bases) ........................................................................................................................................74
4.2 Installing Cabinets (Without Bases)..................................................................................................................................77
4.3 Installing Cabinet Accessories ...........................................................................................................................................80
4.3.1 (Optional) Taking Out PDU2000 Cables and Industrial Connectors...........................................................................80
4.3.2 (Optional) Installing a Branch Ground Copper Bar ......................................................................................................82
4.3.3 (Optional) Installing a Vertical Ground Copper Bar .....................................................................................................83
4.3.4 (Optional) Setting a Cabinet Code Lock........................................................................................................................84
5 Installing the Contained Aisles.......................................................................................... 89
5.1 Installing a Sealing Plate ....................................................................................................................................................89
5.2 Installing Skylights .............................................................................................................................................................91
5.2.1 Skylight Overview...........................................................................................................................................................91
5.2.1.1 600 mm Wide Control Skylight...................................................................................................................................91

FusionModule2000 Smart Modular Data Center
Installation Guide (2000 mm High Cabinets, Single-Row
Aisle Containment, 380 V)
Contents
Issue 04 (2017-06-30)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
vi
5.2.1.2 800 mm Wide Control Skylight...................................................................................................................................91
5.2.1.3 600 mm Wide Flat or Rotating Skylight .....................................................................................................................92
5.2.1.4 800 mm Wide Flat or Rotating Skylight .....................................................................................................................93
5.2.1.5 300 mm Wide Flat Skylight .........................................................................................................................................94
5.2.2 Securing Skylights...........................................................................................................................................................95
5.2.3 Installing a Rotating Skylight Magnetic Lock...............................................................................................................96
5.3 Installing End Doors...........................................................................................................................................................97
5.3.1 Installing a Lower Mounting Kit for the End Door.......................................................................................................98
5.3.2 Installing a Revolving Door..........................................................................................................................................100
5.4 Attaching Cabinet Labels .................................................................................................................................................110
5.5 (Optional) Installing Aisle Lights ....................................................................................................................................111
6 (Optional) Installing Cable Troughs ............................................................................... 115
6.1 Installing a 600 mm Wide Cable Trough.........................................................................................................................115
6.2 Installing a 300 mm Wide Cable Trough.........................................................................................................................119
6.3 Installing an 800 mm Wide Cable Trough ......................................................................................................................121
6.4 Installing End Panels for Cable Troughs.........................................................................................................................121
7 Installing Monitoring Devices ......................................................................................... 123
7.1 Device Layout in the Network Cabinet...........................................................................................................................123
7.2 (Optional) Installing a Server...........................................................................................................................................124
7.3 (Optional) Installing a VCN500.......................................................................................................................................126
7.4 (Optional) Installing a LAN Switch ................................................................................................................................127
7.5 Installing an ECC800........................................................................................................................................................129
7.6 (Optional) Installing a Rack Environment Unit..............................................................................................................131
7.7 Installing Monitoring Components on a Control Skylight.............................................................................................132
7.7.1 Installing a Camera........................................................................................................................................................133
7.7.2 (Optional) Installing a Smoke Detector........................................................................................................................137
7.7.3 (Optional) Installing the Multi-Functional Sensor ......................................................................................................137
7.8 (Optional) Installing Monitoring Components on the End Door...................................................................................139
7.8.1 Monitoring Component Layout for the Revolving Door ............................................................................................139
7.8.2 Installing an Actuator or Converter..............................................................................................................................139
7.8.3 Installing an Alarm Beacon...........................................................................................................................................142
7.8.4 (Optional) Installing a Revolving Door Magnetic Lock.............................................................................................143
7.8.5 Installing Buttons...........................................................................................................................................................148
7.8.6 Installing the Pad Mounting Kit....................................................................................................................................149
7.8.6.1 Installing a Fingerprint and Card Reader..................................................................................................................150
7.8.6.2 Installing a Fingerprint and Card Reader with a Keypad.........................................................................................151
7.8.6.3 Installing a Card Reader with a Keypad ...................................................................................................................152
7.8.6.4 Installing an IC Card Reader......................................................................................................................................153
7.8.6.5 Installing a Pad Power Connector.............................................................................................................................155
7.8.6.6 Installing a Pad ...........................................................................................................................................................158
7.8.6.7 Securing the Pad Mounting Kit .................................................................................................................................159

FusionModule2000 Smart Modular Data Center
Installation Guide (2000 mm High Cabinets, Single-Row
Aisle Containment, 380 V)
Contents
Issue 04 (2017-06-30)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
vii
7.9 Installing Monitoring Components on Cable Troughs ...................................................................................................162
7.9.1 Installing a Smart ETH Gateway..................................................................................................................................162
7.9.2 (Optional) Installing an ETH Converter.......................................................................................................................164
7.10 Installing Temperature Sensors......................................................................................................................................165
7.11 Rules for Deploying T/H Sensors..................................................................................................................................166
7.12 Installing a T/H Sensor...................................................................................................................................................168
7.13 Installing a WLDS900 Water Sensor (Used in Intelligent Micro-Modular)...............................................................170
7.13.1 Connecting a Cable to the WLDS900 Water Detector..............................................................................................170
7.13.2 Laying Out the Water Detection Cable (Top Pipe Routing) .....................................................................................172
7.13.3 Laying Out the Water Detection Cable (Bottom Pipe Routing) ...............................................................................174
8 (Optional) Installing Indoor Cable Trays ....................................................................... 176
9 Installing Cabinet Sealing Plates..................................................................................... 177
10 Cable Routing .................................................................................................................. 179
10.1 System Cabling Rules.....................................................................................................................................................179
10.2 Cable Routes for the Single-Row Aisle Containment Scenario ..................................................................................184
10.3 Cable Routes for Cabinet Door Monitoring Components............................................................................................185
10.4 Cable Routes for the Network Cabinet..........................................................................................................................186
10.5 Cable Routes for Revolving Door Monitoring Components.......................................................................................187
10.6 Cable Routes for the Aisle Lighting System.................................................................................................................188
10.7 Installing an SMS Modem .............................................................................................................................................190
10.8 Connecting the Ground Cables for the Smart Module.................................................................................................192
10.8.1 Grounding Cabinets.....................................................................................................................................................192
10.8.2 (Optional) Connecting Base Ground Cables..............................................................................................................194
10.9 Cable Installation for the Power Supply and Distribution System..............................................................................196
10.9.1 Connecting Battery Cables..........................................................................................................................................196
10.9.2 Connecting Cables to Power Supply and Distribution Devices ...............................................................................201
10.10 Connecting Cables for the Cooling System................................................................................................................202
10.11 Connecting Cables for the Management System........................................................................................................202
11 Installation Verification.................................................................................................. 203
12 Power-On Commissioning ............................................................................................. 204
12.1 Power-On Sequence........................................................................................................................................................204
12.2 Commissioning the Power Supply and Distribution System.......................................................................................204
12.3 Commissioning the Cooling System .............................................................................................................................205
12.4 Commissioning the Management System.....................................................................................................................205
A Appendix ........................................................................................................................... 207
A.1 Contacting Huawei Technical Support...........................................................................................................................207
A.2 Installing Expansion Bolts...............................................................................................................................................207
A.3 Installing a Floating Nut..................................................................................................................................................208
A.4 Scenario with a Column (600 mm Wide ITCabinets Scenario)...................................................................................209

FusionModule2000 Smart Modular Data Center
Installation Guide (2000 mm High Cabinets, Single-Row
Aisle Containment, 380 V)
Contents
Issue 04 (2017-06-30)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
viii
A.4.1 Scenario Description.....................................................................................................................................................209
A.4.2 Installation Process for Scenarios with Columns .......................................................................................................215
A.4.3 Installing a Cabinet Bottom Sealing Plate...................................................................................................................215
A.4.4 Installing Sealing Plates Near theAisle ......................................................................................................................216
A.4.5 Installing the Adjustable Skylight................................................................................................................................218
A.4.5.1 Installing the Skylight Connective Plate ..................................................................................................................219
A.4.5.2 Installing Telescopic Edges.......................................................................................................................................220
A.4.5.3 Installing an Adjustable Skylight Side Sealing Plate ..............................................................................................221
A.4.5.4 Installing the PC Plate Support and PC Plate ..........................................................................................................223
A.4.6 Installing Cable Trays...................................................................................................................................................226
A.4.7 Installing Sealing Plates Away from the Aisle ............................................................................................................229
A.5 Installing a Dehumidifier.................................................................................................................................................230
A.6 (Optional) Connecting Cables to Industrial Connectors ...............................................................................................235
A.7 (Optional) Connecting PDU2000 Cables.......................................................................................................................236
A.8 Cable Routes Inside an IT Cabinet .................................................................................................................................240
A.9 Preparing a Monitoring Cable.........................................................................................................................................244
A.10 (Optional) Connecting Linkage Cables Between the Equipment Room Fire Extinguishing System and Access
Actuator...................................................................................................................................................................................245
A.11 (Optional) Connecting Linkage Cables Between the Equipment Room Fire Extinguishing System and Skylight
Actuator...................................................................................................................................................................................246
B Common Screw Torques.................................................................................................. 248
C Installation Verification................................................................................................... 250
D Acronyms and Abbreviations ......................................................................................... 253

FusionModule2000 Smart Modular Data Center
Installation Guide (2000 mm High Cabinets, Single-Row
Aisle Containment, 380 V)
1 Installation Preparations
Issue 04 (2017-06-30)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
1
1 Installation Preparations
1.1 Precautions for Transportation
Precautions for Air Conditioner Transportation
Only trained personnel are allowed to move the cabinet. Use a pallet truck to transport
the cabinet secured to a wooden support to the installation position. Insert the forks of
the pallet truck in the middle position to ensure balance.
Transport devices by railway, sea, or good road. No excessive tilt or jolt is allowed
during the transportation. The device can only be tilted for at most 15°during loading
and unloading, as shown in Figure 1-1.
To prevent the cabinet from falling over, secure it to a pallet truck using ropes before
moving it.
Move the cabinet with caution. Any bumping or falling may damage the device.
Unpack the device after moving it to the installation position. Avoid damaging the device
during unpacking. Take down the device from the pallet only immediately before
installation.
Figure 1-1 Cabinet tilt

FusionModule2000 Smart Modular Data Center
Installation Guide (2000 mm High Cabinets, Single-Row
Aisle Containment, 380 V)
1 Installation Preparations
Issue 04 (2017-06-30)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
2
Precautions for Placing
Place cardboard boxes in sequence based on their numbers.
Figure 1-2 Arranging components
1.2 Unpacking and Acceptance
Context
Unpack and inspect all cabinets, mechanical parts, and components. Check that all the items
are intact and comply with the packing list on the presence of both the project supervisor and
customer.
Procedure
Step 1 Unpack the carton labeled "Contain Packing List" and take out the Packing List.
Step 2 Check all items against the Packing List.
Step 3 If an item is incorrect or missing, contact Huawei technical support.
Step 4 If any item is damaged, fill in the Cargo Replacement Application Form and report it.

FusionModule2000 Smart Modular Data Center
Installation Guide (2000 mm High Cabinets, Single-Row
Aisle Containment, 380 V)
1 Installation Preparations
Issue 04 (2017-06-30)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
3
Step 5 Sign on the Packing List with the customer after verifying that all required items are
delivered.
Step 6 Store the items properly.
----End
Follow-up Procedure
Put the items to be installed immediately onto an ESD surface, such as a polyethylene (PE)
bag or an expandable polyethylene (EPE) foam. Pack the items not to be installed
immediately with their original packing materials. Put them in a dry and cool environment
without exposure to sunlight or sources of strong electromagnetic radiation.
1.3 Installation Environment Requirements
Ensure that the installation environment meets the requirements before installation.
Table 1-1 Installation environment checklist
Check Item
Requirement
Check Result
Floor bearing
capacity
Standard live load of the equipment
room: 8–12 kN/m2(If the battery
cabinet is contained in the module,
use the standard live load of the
equipment room as a reference.)
Suspended load of the equipment
room: 1.2 kN/m2
Standard live load of the
uninterruptible power system (UPS)
room: 8–10 kN/m2
Standard live load of the battery
room: 16 kN/m2
Standard live load of the monitoring
center: 6 kN/m2
□ Compliant □
Incompliant
Equipment room net
height
See the field requirements for details.
□ Compliant □
Incompliant
Device passage and
door height and
width
Height ≥ 2.2 m and width ≥ 1.2 m
□ Compliant □
Incompliant
Floor levelness
Allowed deviation: 3 mm/2000 mm
□ Compliant □
Incompliant
Elevator
Elevator bearing capacity > 1.5 t
Inner dimensions: height > 2.4 m or
depth > 2.7 m
□ Compliant □
Incompliant
Cable tray
Preinstalled in the equipment room for
signal cables and power cables
□ Compliant □
Incompliant

FusionModule2000 Smart Modular Data Center
Installation Guide (2000 mm High Cabinets, Single-Row
Aisle Containment, 380 V)
1 Installation Preparations
Issue 04 (2017-06-30)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
4
Check Item
Requirement
Check Result
Power supply
380–415 V AC, 3-phase, 50/60 Hz
□ Compliant □
Incompliant
Equipment room fire
extinguishing
Indoor gaseous fire extinguisher
□ Compliant □
Incompliant
Floor drain
DN50 or larger, made of cast iron or
stainless steel
□ Compliant □
Incompliant
Module grounding
The equipment room grounding
system must be a TN-S or TN-C-S
system.
The equipment room ground grid
must have a ground resistance of 10
ohms at most (If the ground
resistance exceeds 10 ohms, ensure
that the equivalent ground radius of
the ground grid exceeds 5 m.)
Ground bars must be deployed over
the cable tray or under the raised
floor
□ Compliant □
Incompliant
Monitoring port
One LAN switch Ethernet port:
connects to the customer subnet to
monitor devices inside the module.
(Optional) Two fire control dry
contacts (access actuator and PDC
fire control terminal): connect to the
fire extinguishing system of the
equipment room for interaction.
(Optional) SIM card: supports 3G
(WCDMA) communication and is
compatible with 2G (GSM)
communication. If the collector
supports the SMS alarm function,
configure a SIM card.
NOTE
If there are multiple modules, configure a
collector for each module. For the collectors
that support the SMS alarm function,
configure a SIM card for each.
IP address: Each collector, camera,
and VCN require an IP address,
respectively.
□ Compliant □
Incompliant
If any of the requirements is not met, contact Huawei technical support.

FusionModule2000 Smart Modular Data Center
Installation Guide (2000 mm High Cabinets, Single-Row
Aisle Containment, 380 V)
1 Installation Preparations
Issue 04 (2017-06-30)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
5
1.4 Site Requirements
Equipment Room Height Requirement
The net height of an equipment room must not be lower than 2600 mm in the case of a
single-row aisle containment. The maximum module height includes the size of open
skylights and does not vary depending on the camera support and fire extinguisher support, as
shown in Figure 1-3.
The clearance for fire extinguishing nozzles is subject to specific fire extinguishing
requirements and is not considered in this section.
Table 1-2 Equipment room net height requirement (without bases)
Scenario
Equipment Room Net Height
2000 mm high cabinet
> 2600 mm
When the bases are configured, the equipment room net height equals the equipment room net
height (without bases) plus the base height.

FusionModule2000 Smart Modular Data Center
Installation Guide (2000 mm High Cabinets, Single-Row
Aisle Containment, 380 V)
1 Installation Preparations
Issue 04 (2017-06-30)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
6
Figure 1-3 Smart module height
Cabinet height L1: 2000 mm
Open-skylight height L2: 550 mm
Smart Module Layout Requirement
Figure 1-4 Smart module layout requirement
1.5 Documents
Before installation, prepare the following documents in addition to this document.

FusionModule2000 Smart Modular Data Center
Installation Guide (2000 mm High Cabinets, Single-Row
Aisle Containment, 380 V)
1 Installation Preparations
Issue 04 (2017-06-30)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
7
Table 1-3 Documents for hardware installation
Documentation
Purpose
Obtaining Method
(Remarks)
Onsite engineering layout
drawing
Describes the cabinet
layout.
Provided by the engineering
designer or technical support
engineer.
Quick Reference Guide to
the Smart Modular Data
Center
Smart Module Quick
Installation Guide
describes the unpacking
sequence, installation
procedure, and
installation precautions.
Smart Module
Management System
Wiring Diagram
describes how to route
cables for the
management system.
The document is delivered
with the device, or you can
click Download.
UPS5000-E-(40 kVA–128
kVA) Quick Guide
(Integrated UPS 2.0)
Describes the installation,
cable connection, and
power-on operations for the
integrated UPS.
The document is delivered
with the device, or you can
click Download.
PDU8000 Modular
Precision PDC Quick Guide
(1100 mm Deep)
Describes the installation,
cable connection, and
power-on operations for the
PDU8000 Precision PDC.
Click Download.
NetCol5000-A 25 kW Air
Cooled In-row Precision Air
Conditioner Quick Guide
(300 mm Wide)
Describes the installation,
cable connection, and
power-on operations for the
NetCol5000-A 25 kW air
conditioner.
The document is delivered
with the device, or you can
click Download.
NetCol5000-A 25 kW&35
kW Air Cooled In-row
Precision Air Conditioner
Quick Guide (600 mm Wide)
Describes the installation,
cable connection, and
power-on operations for the
NetCol5000-A 25 kW&35
kW air conditioner.
The document is delivered
with the device, or you can
click Download.
NetCol500 Variable Speed
Outdoor Unit User Manual
Describes the installation,
cable connection, and
power-on operations for the
NetCol500 Variable Speed
Outdoor Unit.
Click Download.
Indoor Cable Tray
Installation Guide
Describes how to install the
in-room cable trays.
Click Download.
Smart Module Battery
Wiring Diagram
Provides guidance about
battery arrangement and
cable connections.
Delivered with battery
cables.

FusionModule2000 Smart Modular Data Center
Installation Guide (2000 mm High Cabinets, Single-Row
Aisle Containment, 380 V)
1 Installation Preparations
Issue 04 (2017-06-30)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
8
Documentation
Purpose
Obtaining Method
(Remarks)
iBAT 2.0-CIM01C2 User
Manual
Describes the installation,
cable connection, and
power-on operations for the
CIM and BIM.
Click Download.
PDU8000 Integrated Power
Distribution Cabinet Quick
Guide (Modular)
Describes the installation,
cable connection, and
power-on operations for the
integrated PDC.
The document is delivered
with the device, or you can
click Download.
iManager NetEco Device
Commissioning
Guide-(NetEco Version)
Describes how to connect
monitoring hardware to the
NetEco.
The NetEco version depends
on the version in use. Click
on the NetEco WebUI to
obtain the NetEco version in
use. Click Download.
iManager NetEco Product
Document - (NetEco
Version)
Describes how to install
monitoring hardware and
configure monitoring
software.
The NetEco version depends
on the version in use. Click
on the NetEco WebUI to
obtain the NetEco version in
use. Click Download.
ECC800 Data Center
Controller (ECC Version)
User Manual
Describes the overview of
the ECC800 and its ports,
installation, commissioning,
user interfaces,
maintenance, and
troubleshooting.
The ECC800 version
depends on the version in
use. Click on the ECC800
WebUI to obtain the
ECC800 version. Click
Download.
1.6 Tools and Instruments
This section lists the tools and instruments required for installation.
Table 1-4 General tools
Name, Specifications, and Appearance
Protective gloves
Marker
Measuring tape (5
m)
Level
Step ladder (2 m)
Phillips screwdriver
(M4, M6, and M8)
Phillips screwdriver
M4 (length < 100
mm)
Flat-head
screwdriver (2–5
mm)

FusionModule2000 Smart Modular Data Center
Installation Guide (2000 mm High Cabinets, Single-Row
Aisle Containment, 380 V)
1 Installation Preparations
Issue 04 (2017-06-30)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
9
Name, Specifications, and Appearance
Adjustable wrench
(6")
Socket wrench
M4/M6/M8/M12
Hex key
Box-end wrench
(M6, M8, and M12)
Torque wrench (28
mm)
Solid wrench
(12#/13#/18#)
Cotton cloth
Labels
Electric screwdriver
Hand drill (Φ3,
Φ3.7, Φ4, Φ4.5, Φ5,
Φ6, Φ10, and Φ12
drill bits)
Hammer drill (Φ16
drill bit)
Heat gun
Laser locator
Utility knife
Electrician's knife
Impact tool
Polyvinyl chloride
(PVC) insulation
tape
Needle-nose pliers
Diagonal pliers
RJ45 crimping tool

FusionModule2000 Smart Modular Data Center
Installation Guide (2000 mm High Cabinets, Single-Row
Aisle Containment, 380 V)
1 Installation Preparations
Issue 04 (2017-06-30)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
10
Name, Specifications, and Appearance
Crimping tool
Wire stripper
Hydraulic pliers
Wire clippers
Cable ties
Multimeter
Electroprobe
Brush
Claw hammer
Vacuum cleaner
Hacksaw
Handsaw
Right angle
Heat shrink tubing
Network cable tester
Rubber mallet
Adjustable socket
screwdriver
Flashlight
Clamp meter
Phase sequence
meter
NOTE
This table may not list some tools required at specific sites. Onsite installation personnel and technical
support personnel should prepare tools based on site requirements.

FusionModule2000 Smart Modular Data Center
Installation Guide (2000 mm High Cabinets, Single-Row
Aisle Containment, 380 V)
1 Installation Preparations
Issue 04 (2017-06-30)
Huawei Proprietary and Confidential
Copyright © Huawei Technologies Co., Ltd.
11
Table 1-5 Transportation and unpacking tools
Tool Appearance, Specifications, and Name
Pallet truck
Diesel forklift
Lifting rope (bearing
capacity ≥ 400 kg)
Lever (bearing
capacity ≥ 400 kg)
Table 1-6 Air conditioner tools
Tool Appearance, Specifications, and Name
Cutter
Water pipe thread
sealanta
Welding torch
5% silver solder
Oxygen
Acetylene
Hot melt device (for
rigid water pipes)
Nitrogend
Pipe bender
Pipe expander
Pressure gauge (2
PCS)b
Leather hose (5
PCS)b
Vacuum pumpc
Thermocouple
temperature sensor
Antifreeze gloves
Electronic scale