Huawei OptiXstar K153-10 User manual

Huawei OptiXstar K153-10
Quick Start
Issue 01
Date 2023-04-28
HUAWEI TECHNOLOGIES CO., LTD.

Copyright © Huawei Technologies Co., Ltd. 2023. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any means without prior
written consent of Huawei Technologies Co., Ltd.
Trademarks and Permissions
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and
the customer. All or part of the products, services and features described in this document may not be
within the purchase scope or the usage scope. Unless otherwise specied in the contract, all statements,
information, and recommendations in this document are provided "AS IS" without warranties, guarantees
or representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every eort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Huawei Technologies Co., Ltd.
Address: Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China
Website: https://www.huawei.com
Email: [email protected]
Issue 01 (2023-04-28) Copyright © Huawei Technologies Co., Ltd. i

Contents
1 Product Overview.................................................................................................................... 1
2 Placing the Device................................................................................................................... 3
2.1 Stand up on the desktop...................................................................................................................................................... 4
2.2 Clamped in a socket panel...................................................................................................................................................5
2.3 Embedded in a 86 Box...........................................................................................................................................................7
2.4 Mounted on a Wall.................................................................................................................................................................9
3 Connecting Cables.................................................................................................................11
4 Indicator Description............................................................................................................ 14
5 FAQs..........................................................................................................................................15
Huawei OptiXstar K153-10
Quick Start Contents
Issue 01 (2023-04-28) Copyright © Huawei Technologies Co., Ltd. ii

1 Product Overview
Huawei OptiXstar K153-10 is a Slave FTTR for the Huawei FTTR OptiXstar F30 Pro.
It supports ultra-gigabit broadband access through upstream bers and provides
users with ultra-gigabit dual-band Wi-Fi and ultra-gigabit network ports.
Figure 1-1 Device Appearance
Huawei OptiXstar K153-10
Quick Start 1 Product Overview
Issue 01 (2023-04-28) Copyright © Huawei Technologies Co., Ltd. 1

Figure 1-2 Mounting accessories
NO TE
● The appearance shown in this document may be dierent from the actual appearance
of the product. The actual product prevails.
● This device is recommended only for single room Wi-Fi coverage.
● Working mode of the device: bridge mode.
Huawei OptiXstar K153-10
Quick Start 1 Product Overview
Issue 01 (2023-04-28) Copyright © Huawei Technologies Co., Ltd. 2

2 Placing the Device
The device can be placed vertically on a desk, clamped in a socket panel,
embedded in a 86 Box, or mounted on a wall.
CA UTION
Do not expose the device outdoors.
WARNING
1. Install devices only by professional personnel. Do not install devices without
permission.
2. For your safety, install an accessible disconnection device on the outside of the
product. The disconnection device and the product must be installed by
professional personnel. Installation and disassembly are not allowed without
permission. At the same time, be sure to disconnect the power supply before
installation and removal by professional personnel.
3. Before installation, disconnect the power supply. In the 86-type electrician box,
ask professional personnel to lead out the cables from the wall. Keep a certain
distance between the cables to avoid contact with each other.
4. Do not use cleaners, gasoline, ammonia or other corrosive chemicals to wipe
the product.
5. This product is only suitable for installation on concrete or non-ammable
surfaces.
6. During the installation, use protective terminals to protect the optical ber to
prevent the end face of the optical ber from being contaminated.
7. The tools and auxiliary materials that are not delivered with the equipment
must be prepared by professional personnel.
Huawei OptiXstar K153-10
Quick Start 2 Placing the Device
Issue 01 (2023-04-28) Copyright © Huawei Technologies Co., Ltd. 3

NO TE
● Suitable for hotels, families and other places. For dierent household types, match
products as needed.
● Please use the international standard 86-type electrician box for installation.
● Keep the device away from electrical appliances that generate strong magnetic or
electric elds, such as microwave ovens.
● All diagrams in this document may be dierent from the actual product. These
dierences do not aect the functions of the product.
2.1 Stand up on the desktop
2.2 Clamped in a socket panel
2.3 Embedded in a 86 Box
2.4 Mounted on a Wall
2.1 Stand up on the desktop
After connecting optical bers, network cables, and power cables to the device,
push the base in the direction shown in the gure until it is completely clamped to
the device.
NO TE
When the device is placed vertically on a desk, if the device is connected to a bent network
cable, the device may not be stable on the desk. Users are advised to arrange the network
cable before connecting the device.
Huawei OptiXstar K153-10
Quick Start 2 Placing the Device
Issue 01 (2023-04-28) Copyright © Huawei Technologies Co., Ltd. 4

2.2 Clamped in a socket panel
WARNING
1. It is recommended that the operation be performed by an engineer with an
electrician certicate.
2. Before the installation, disconnect the power supply.
Step 1 Remove the cover of a socket panel and loosen the screws. Open the folding
bracket, clamp it behind the socket panel, and tighten the screws to secure the
cover.
NO TICE
You only need to loosen the screws on the panel, and do not need to remove the
screws.
Huawei OptiXstar K153-10
Quick Start 2 Placing the Device
Issue 01 (2023-04-28) Copyright © Huawei Technologies Co., Ltd. 5

Step 2 Connect cables, such as optical bers, network cables, and power cables, coil the
cables in the bracket, and secure the cables with adhesive tapes.
NO TICE
● The outer ring of the braclet is used to coil optical ber, and the inner ring is
used to coil power cable.
● When coiling bers, exercise caution to prevent the bers from being bent or
damaged.
Step 3 Insert the card hole at the rear of the device into the buckle of the bracket to
secure the device.
Huawei OptiXstar K153-10
Quick Start 2 Placing the Device
Issue 01 (2023-04-28) Copyright © Huawei Technologies Co., Ltd. 6

----End
2.3 Embedded in a 86 Box
CA UTION
The device cannot be installed in an 86-type electrician box with strong current. It
can be installed only in an 86-type electrician box that is empty or has only weak
current.
Step 1 Lead the cable out of the wall through the cable hole of the bracket.
Huawei OptiXstar K153-10
Quick Start 2 Placing the Device
Issue 01 (2023-04-28) Copyright © Huawei Technologies Co., Ltd. 7

Step 2 Align the bracket with the screw holes on the 86-type electrician box, and install
the screws to x the bracket. Do not tighten the screws too tightly.
Step 3 Connect cables, such as optical bers, network cables, and power cables, coil the
cables in the bracket, and secure the cables with adhesive tapes.
NO TICE
● The outer ring of the braclet is used to coil optical ber, and the inner ring is
used to coil power cable.
● When coiling bers, exercise caution to prevent the bers from being bent or
damaged.
Huawei OptiXstar K153-10
Quick Start 2 Placing the Device
Issue 01 (2023-04-28) Copyright © Huawei Technologies Co., Ltd. 8

Step 4 Insert the card hole at the back of the device into the buckle of the bracket to
secure the device. Then, the device is installed in the 86-type electrician box.
----End
2.4 Mounted on a Wall
Step 1 Secure the bracket to a wall using screws.
Huawei OptiXstar K153-10
Quick Start 2 Placing the Device
Issue 01 (2023-04-28) Copyright © Huawei Technologies Co., Ltd. 9

Step 2 After connecting bers, network cables, and power cables to the device, mounted
device onto the buckles on the bracket to secure the device.
NO TICE
● Determine whether to coil the cable based on the length of the redundant
cable. If the cable is too long, coil the cable in the bracket and then secure the
device.
● The outer ring of the braclet is used to coil optical ber, and the inner ring is
used to coil power cable.
----End
Huawei OptiXstar K153-10
Quick Start 2 Placing the Device
Issue 01 (2023-04-28) Copyright © Huawei Technologies Co., Ltd. 10

3 Connecting Cables
NO TE
When expanding Wi-Fi at your home, a professional needs to connect the Slave FTTR to the
Master FTTR using optical network components. In this case, the Slave FTTR automatically
synchronizes the Wi-Fi parameters of the Master FTTR. The Wi-Fi of the Master FTTR is
used for service provisioning and maintenance. You can use the dual-band Wi-Fi of the
Slave FTTR.
NO TICE
The appearance shown in this document may be dierent from the actual
appearance of the product. The actual product prevails.
Huawei OptiXstar K153-10
Quick Start 3 Connecting Cables
Issue 01 (2023-04-28) Copyright © Huawei Technologies Co., Ltd. 11

No. Interface or
button
Description
1 2.5GE-1, GE-2 The port is auto-negotiated to a LAN port when
connected to a computer or STB, and to a WAN port
when connected to the LAN port of a Master FTTR.
2 Power Connects to the power adapter.
3 Fiber Connects to the Master FTTR to implement ber-to-
room transmission.
4 LED/WPS Indicator and WPS integrated switch.
● Short press: Turns the indicator on or o.
● Press and hold for more than 3 seconds: Enables the
WPS pairing function.
Huawei OptiXstar K153-10
Quick Start 3 Connecting Cables
Issue 01 (2023-04-28) Copyright © Huawei Technologies Co., Ltd. 12

No. Interface or
button
Description
5 Reset When the device is starting, use a needle-shaped object
to press and hold this button for more than 2 seconds
until indicator turn o. After the device restarts and the
indicator turns on, the factory settings are restored.
NOTE
Exercise caution when pressing the button. If you cannot access
the Internet after the device is restored to factory settings,
contact your service provider for help.
Huawei OptiXstar K153-10
Quick Start 3 Connecting Cables
Issue 01 (2023-04-28) Copyright © Huawei Technologies Co., Ltd. 13

4 Indicator Description
Indica
tor
Status Description
Red steady on ● The device is being powered on.
● The device is started but not connected to the
upstream network.
Red: Blinking
slowly
(once per
second)
The device has detected a pairable device.
Red: Blinking
quickly(twice
per second)
● The device is being cascaded.
● WPS pairing is being performed on the device as an
access point.
White steady on The device is started and connected to the upstream
network.
NO TE
If the Slave FTTR is not powered on, all indicators are o.
Huawei OptiXstar K153-10
Quick Start 4 Indicator Description
Issue 01 (2023-04-28) Copyright © Huawei Technologies Co., Ltd. 14

5 FAQs
How to set up a network?
In the network where the Slave FTTR is connected to the FTTR, the network
settings of the Master FTTR are synchronized. No further conguration is required.
How to restore the factory settings of the device?
Press and hold the Reset button of the device for more than 2 seconds using a
needle, and release the button after the indicator turns o. After the device
restarts and the red indicator turns on, the factory settings are restored.
NO TE
After the Slave FTTR is restored to factory settings, connect it to the Master FTTR. The
device automatically synchronizes the conguration of the Master FTTR. The Slave FTTR
does not need to be congured.
How to change the Wi-Fi name and password of the device?
For the FTTR all-optical Wi-Fi solution, you are advised to change the Wi-Fi name
and password on the Master FTTR. The Slave FTTR automatically synchronizes the
modication.
How do I log in to the web page of the device in an FTTR network?
After the Slave FTTR is connected to the FTTR network, the FTTR network
automatically assigns an IP address to the device. The device can be accessed
through this IP address.
NO TE
You can view the IP address on the Master FTTR or NCE. The login password is the same as
that on the Master FTTR.
How Can I Retrieve My Login Password?
1. Restore the factory settings of the Master FTTR. The Slave FTTR automatically
synchronizes the modication.
Press and hold the Reset button of the Master FTTR for more than 10 seconds
using a needle, and release the button after the indicator turns o. After the
Huawei OptiXstar K153-10
Quick Start 5 FAQs
Issue 01 (2023-04-28) Copyright © Huawei Technologies Co., Ltd. 15

device restarts and the red indicator turns on, the factory settings are
restored.
2. Enter the IP address in the address box of a browser and press Enter. For
details about the IP address, see the product nameplate.
3. Follow the guide to set administrator login password. You can also set the Wi-
Fi password as the device management password.
Huawei OptiXstar K153-10
Quick Start 5 FAQs
Issue 01 (2023-04-28) Copyright © Huawei Technologies Co., Ltd. 16