Huawei UPS5000-A-400K-FTS User manual

1
UPS5000-A-(400 kVA–600 kVA)
Quick Guide (60 kVA Power
Modules)
1Overview
Model UPS5000-A-400K-FTS UPS5000-A-500K-FTS UPS5000-A-600K-FTS
Dimensions
(H x W x D) 2000 mm x 1200 mm x 850 mm 2000 mm x 1400 mm x 850 mm
1. Before installation, read the user manual carefully to get familiar with product information
and safety precautions.
2. Use insulated tools during installation and operations.
3. Only engineers certified by the Company or its agents are allowed to install, commission, and
maintain the UPS. Otherwise, personal injury or device damage may occur, and the UPS faults
caused are beyond the warranty scope.
UPS5000-A-400K-FTS UPS5000-A-500K-FTS
(1) Power units
(2) Control unit
(3) Mains input switch
(4) Output switch
(5) Power distribution unit
(
PDU) cover
(6) Maintenance bypass switch
(7) Bypass input switch
(8) Bypass unit
UPS5000-A-(400 kVA-600 kVA)
Quick Guide (PF=0.9)
Copyright © Huawei Technologies Co., Ltd. 2022.
All rights reserved.
Issue: 05
Part Number: 31509968
Date: 2022-01-27

2
400K/500K Hole Dimensions
Determining the UPS Installation Position
2.1
The UPS can be installed on the channel steel or floor. Determine the mounting hole positions
using a marking-off template, drill holes, and install expansion sleeves based on site requirements.
2Installing the UPS
(1) Power units
(2) Control unit
(3) Mains input switch
(4) Output switch
(5)
PDU cover
(6) Maintenance bypass switch
(7) Bypass input switch
(8)
Bypass unit
A: mounting holes on the channel steel
B: mounting holes on the floor
Unit: mm
UPS5000-A-600K-FTS

3
Securing the UPS
2.2
Floor mounting: Secure the cabinet to the floor using eight M12x60 expansion bolts.
Channel steel mounting: Secure the cabinet to the channel steel using eight M12x60
common bolts.
(1) Mounting hole on the floor
(2) Mounting hole on the channel steel
A: mounting holes on the channel steel
B: mounting holes on the floor
Unit: mm
600K Hole Dimensions

4
3Installing Cables
•When preparing cables, keep away from the cabinets to prevent cable scraps from entering
the cabinet. Cable scraps may cause sparks during power-on and cause personal injury or
device damage.
•After cables are installed, clean the cabinets promptly. Ensure that there is no foreign
matter inside and around the cabinets.
•Prepare terminals onsite. The length of the copper wire should be the same as that of the
part of the terminal that covers the conductor.
UPS Cable Connection Reference
3.1
The cabling route is for reference only. Connect cables based on site requirements.
1. Two power sources are used as an example.
2. If there is only one power source, the bypass input cables do not need to be connected and
the interconnecting copper bars do not need to be removed.
Installing the Front and Rear Anchor Baffle Plates
2.3

5
1. Open the front door of the bypass cabinet
and remove the covers of the power
distribution subrack. The UPS5000-A-400K-
FTS is used as an example.
3. Remove the copper bars between the
mains and bypass inputs. (Skip this step
if there is only one power source.)
4. Connect a ground cable.
2. Remove the top cover from the cabinet
based on cable routes and dimensions.
Scenario 1: Routing Cables from the Top
Installing Cables
3.2

6
6. Connect the output power cables.
5. Connect the mains input power cables.
7. Connect the bypass input power cables. 8. Connect battery cables.
M16x55 bolts are used to connect the mains input power cables, output power cables,
bypass input power cables, and battery cables for the 500K and 600K cabinets.

7
The wire routed from the middle point of
positive and negative battery strings is the
neutral wire. Take a battery string
consisting of 40 batteries for example. The
battery neutral wire is routed from the
middle between positive and negative
battery strings, each consisting of 20
batteries.
The figure shows the signal cable routing
and is for reference only. Connect the
cable based on the actual situation.
1. Remove the cable covers from the bottom of
the cabinet, drill holes in the covers, attach
grommet strips to the hole edges for
protecting cables, and reinstall the cable
covers.
2. Connect power and signal cables.
For the screw specifications and torque
used for connecting cables in a bottom
cable routing scenario, refer to the top
cable routing scenario. This section only
shows the cable routes in the bottom cable
routing scenario.
Scenario 2: Routing Cables from
the Bottom
For the cable connection method
for the TN-C system, see the user
manual.
9. Connect the signal cable.

8
4Verifying the Installation
(1) Switches
(2) Mains input wiring
copper bar
(3) Battery input wiring
copper bars
(4) Output wiring
copper bar
(5) Bypass input wiring
copper bar
(6) Cabinet rear
1. Check that there is no foreign matter in the cabinets.
2. After routing cables and checking cable connections, use sealing putty to fill in the gap
between the cables and the cabinets. (Remove the paper protective film from the sealing putty
and retain the transparent film. When using the putty, ensure that the transparent film faces
upward.)
Paper
protective film
Transparent
film
Sealing putty
3. After the checks are performed, reinstall all the covers.
Sealing putty must be used as a whole and
the gap can be sealed only from the top.
The 400 kVA model is used as an
example. The procedures for 500
kVA/600 kVA models are the same.

9
4. Do not remove the dustproof cover before power-on to prevent dust from entering the cabinet.
Do not remove the
dustproof cover before
power-on.
Power-On
5.1
Initial Startup
5.2
Turn on the upstream bypass and mains input switches.
Turn on the UPS bypass input switch, mains input switch, and output switch.
After the system is powered on, it starts initialization. The MDU displays an
initialization progress bar.
5Powering On and Starting the UPS
1. Before powering on the UPS, ensure that the UPS has passed all check items in the UPS5000
Commissioning and Acceptance Report and Chapter 4 Verifying the Installation.
2. Measure the voltage and frequency of the mains and bypass inputs of the UPS, or the
voltage and frequency output from the external input power distribution cabinet to the UPS.
Ensure that the line voltage is in the range of 138–485 V AC and the frequency is in the
range of 40–70 Hz.
1. If the UPS is powered on for the first time, you need to obtain the startup password from
the Service Expert app. Skip this step if the UPS is not powered on for the first time.
2. The Service Expert app can be downloaded from Huawei AppGallery and can only run on
Android.
3. The Settings Wizard screen may vary with versions. The parameters depend on the actual
product.

10
1. Obtain the startup password.
Download and install the Service Expert app.
After login, tap Power-on password
activation on the screen. A message is
displayed, indicating whether to start the UPS.
Tap OK.
Insert the WiFi module into the USB port on
the MDU. Enable the mobile phone WLAN,
search for the UPS_WIFI signal, and connect to
the WiFi signal. The password is Changeme.
Set the Site and Device Type as required, and
connect the device. Set IP to 192.168.0.10, Port
to 443, Username to admin, and Password to
Changeme, and tap Login.
Enter Bar code and Verification code
obtained from the LCD on the Offline
Activation screen. Tap Generate PWD to
generate a startup password.
Set Site and Device Type as required,
and tap Offline Activation.
Enter the generated password in the
password text box on the LCD to start
the UPS.
Use the app to
start the UPS
online?
Yes
No, start
the UPS
offline
On the app home screen, tap StartUp to access the Set Startup screen.