HULALA HOME SBRB0913 User manual

HULALA
H O M E
01/28
NOTE:
This brochure contains IMPORTANT safty info. Please read and keep for future
reference.
ITEM NO.SBRB0913

MAINTAINANCE AND WARNING
1.Keep furniture away from heat sources.
2.Do not clean furniture with harsh cleaner or polishes.Do not use
detergents,solvents,abrasives,spray packs or leather cleaner.
Use non-color mild soap with warm water to clean spills(Mix 1:10
soap to water).
3.Do not place furniture under direct sunlight,material will possibly
fade over time.
4.Do not use on site dry cleaning machine.Children should not climb
or jump on the furniture.
5.Do not write on furniture that is not protectedby a padded barrier.
6.Not for commercial use,only for residential use.
Weight Limitation
150 LBS
02/28

EXPLOSIVE VIEW
2PERSONEN
03/28

PARTS LIST
x1
x3
x1
x3
x1
x1
x1
x2
04/28
x2x2x2x4
x1x1

HARDWARE LIST
TOOL LIST
x1 x1
05/28
M4
x10 x8 x68x10 x20 x10
Ø6*35mm Ø3.5mm*14
x16 x4 x2 x6
Ø6mm*35
x4
x10 x24 x4
x4
x4
Ø4*18''
Ø8*30mm Ø15*12mm Ø7*40mm
Ø6*45mm
Ø4*35
x4 x2
x1

HARDWARE SPARE LIST
x1 x6
Ø3.5mm*14
Ø4*18''
x1 x1
Ø6mm*35
Ø6*45mm
06/28

ASSEMBLY INSTRUCTIONS
STEP-1
07/28
x1x10
1.Prepare for part A. Align the holes in part A, insert wooden dowel
#2 by hand, tighten with screwdriver #21 tighten #1。
x10
Ø6*35mm Ø8*30mm

ASSEMBLY INSTRUCTIONS
STEP-2
08/28
1.Connect the part A with part C&D&E&F. align the hole in the part
C&D&E&F,insert the bolt #1 and wooden dowel #2 in part A into part
C&D&E&F. insert cam bolt #3 into the corresponding hole of side
panel C&D&E&F,and tighten the nuts #3 with a screwdriver #21. After
installation, cover the screw holes with #13. Make sure the groove is
in same side as picture show.
x1x10x10
Ø15*12mm

ASSEMBLY INSTRUCTIONS
STEP-3
1.slide in the part J,K into the groove in part D,E and E,F and F,E,and C,E .
make sure they are also in groove in part A.Insert the wooden dowel #2 into
the part C&D&E&F as the picture show.
09/28
x10
Ø8*30mm

ASSEMBLY INSTRUCTIONS
STEP-4
x1
10/28
M4
#21
x10
1.Connect the part B the pre-assembled unit in step 3. Then
align the holes in part B,Insert screw #4 and push it down so that
it connects to parts C&D&E&F. Next,and tighten the screw #4
with an Allen key #21.
Ø7*40mm
#21

ASSEMBLY INSTRUCTIONS
STEP-5
1.Align the holes of part N, insert the bolt #19, and bolt the middle foot
into the bolt #19 .
x1
11/28
M4
#19
#19
#19
#19

ASSEMBLY INSTRUCTIONS
STEP-6
x1
12/28
M4
#20
x2
Ø6*45mm
75%
1.Prepare the leg racks. Align the holes of the N part with the holes
of the L part, insert the screw #10, and tighten the screw #10 with the
allen key #20.
#20

ASSEMBLY INSTRUCTIONS
STEP-7
x1
13/28
M4
#20
x6
Ø6mm*35
#20
100%
After all the screw rods
are put into the screw
holes, tighten them all
again.
75%
100%
1.connect the leg frame to the cabinet.Attach the leg frame to the
pre-assembled unit in step 4 with a screw #11 and tighten #11 with a
allen key #20.

ASSEMBLY INSTRUCTIONS
STEP-8
x1
14/28
M4
#21
Attention:
Before the next step, adjust
the feet of the locker to keep
it level.

x16
ASSEMBLY INSTRUCTIONS
STEP-9
1.Insert hardware #5 into part K&J as shown, screw in screw #6
using screwdriver #󲹿󲹾󲹭and tighten fully.
15/28
x1
M4
#21
x16
#6
Ø3.5mm*14
#6
#21

ASSEMBLY INSTRUCTIONS
STEP-10
16/28
x24
M4
#14
1.Insert shelf pin #14 into pre-assemble unit at step 7.attach
adjustable shelf G&H to pin #14.
#14
#14

ASSEMBLY INSTRUCTIONS
STEP-11
17/28
#6 x8 #21 x1
1.Use screw #6 to attach the hinges #8 to door panel (I)，tighten
screws #6 with screwdriver #21.
x4
#6
#21
#6
#6
#6
#6

ASSEMBLY INSTRUCTIONS
STEP-12
18/28
x16 #21 x1
#6
1.Use screw #6 to attach left door (I) and right door (I) to
pre-assemble unit at step 8 ,tighten screw #6 with screwdriver #21 .
D
#6
#21

ASSEMBLY INSTRUCTIONS
STEP-13
19/28
#6 x8 #21 x1
1.Use screw #6 to attach the hinges #9 to door panel (I)，tighten
screws #6 with screwdriver #21.
x4
#6
#21

ASSEMBLY INSTRUCTIONS
STEP-14
x1
20/28
#21
x8
#6
1.Use screw #6 to attach middle door (I) to pre-assemble unit at
step 10 ,tighten screw #6 with screwdriver #21 .
#6
#21