HULALA HOME TVSBSD0389 User manual

NOTE:
ITEM NO. TVSBSD0389
This brochure contains IMPORTANT safty info. Please read and keep for
future reference.
1/16

MAINTAINANCE
AND WARNING
Keep furniture away from heat.
Do not clean furniture with harsh cleansers
or polish. Do not use detergents, Solvents,
abrasives, spray packs or leather cleaner. Use
non-color mild soap with warm water clean
spills(Mix 1:10 soap to water)
Do not place furniture under direct sunlight,
material will possibly fade over time.
Do not use on site dry Cleaning machine.
Children should not climb or jump on the
furniture.
Do not write on furniture without a padded
barrier to protect the surface.
Not for commercial use, For residential use
only.
Weight Limitation
80LBS
2/16

3/16
PARTS
LIST
19 x118 x1
17 x2
16 x1
15 x1
14 x1
13 x1
12 x1
11 x1
10 x1
9 x1
8 x2
7 x1
6 x1
5 x1
4 x1
3 x1
2 x1
1 x1

Explosive View
4/16
18
17
17
16
15
14
13
12
19
11
10
98
87
6
5
4
3
1
2

Be sure to check all packing material carefully for
small parts, which may have come loose inside the
carton during shipment.
5/16
R x4
x4
x4
C
I
E
M4*18mm
x44x8
8*30mm
M6*50mm
Dx20
x6
J
A B G
x16 x16
M6*35mm 15mm
H
x4 K
x2
L
x3
Fx16
Q
M4
x1
4*35mm
O
3.5*14mm
M7*50mm
x4
N
x8
x16
M P
x9
HARDWARE
LIST
SPARE
x4

6/16
ASSEMBLY
INSTRUCTIONS
Preparing part 1. align the hole in the part 1, insert the
wooden dowel D by hand, screw and tighten the A by
screwdriver.
D*2
A*2
5
A*2
D*2
6
A
Preparing part 5and 6. align the hole in the part 5and 6,
insert thewooden dowel D by hand, screw and tighten the A
by screwdriver.

7/16
Slide in the part 9 into the groove in part 5,6 and 1, then align the hole in
the part 1 and insert the bolt A and wooden dowel D in part 5 and 6,
tighten the nut B by screwdriver and cover the screw hole by lid N after the
installation is finished.
Connect the part 3 and 4 with part 1Align the hole in the part 1 and insert
the hole in part 1, tighten the nut B by screwdriver and cover the hole by
the wooden dowel D and bolt A into lid N after installation is finished.
Connect the part 7 with part 5 and 6. align the hole in the part 7,
insert the bolt A and wooden dowel
D in part 5 and 6 into part 7.
tighten with the
nut B. cover the
screw hole after
installation
is finished.
Make sure the
groove is in
same side as
picture show.

8/16
slide in the part 8 into the groove in
part 3, 5 ,and 4,6. make sure they are also
in groove in part 1.
Slide in the part 10 into the groove 5,6 and 7.
Connect the part 2 with the finished part. Insert the wooden dowel D into
the part 3,4,5,6 as the picture show.
Then align the hole in the part 2,
insert and push down part 2 to make it
connect to the part 3,4,5,6. next, tighten the
part 2 with screw C by Allenkey P.

9/16
Preparing the leg frame. Align the hole in the part
18 and the hole in the part 17, screw and tighten
the screw M by Allenkey P. then screw in the
hardware O in the part 17 as the picture show.
connect the leg frame to the cabinet. Align the hole in the leg
frame part 17 and 18 to the hole in the part 2, screw in and
tighten the screw M by Allenkey P.

10/16
Preparing the drawers. Align the holes in the part 12, screw bolt A
into the part 12 by screwdriver.
Assemble the drawer handler on the part 12 as the picture show.
insert the hardware F into the part 8, 9,10
as the picture show, screw in the E
and fully tighten.
Installing the hardware Q on the part 1
both sides as the picture show.