HULALA HOME SCBSD0548 User manual

NOTE:
SCBSD0548
This brochure contains IMPORTANT safty info. Please read and keep for
future reference.
1/15

MAINTAINANCE
AND WARNING
Keep furniture away from heat.
Do not clean furniture with harsh cleansers
or polish. Do not use detergents, Solvents,
abrasives, spray packs or leather cleaner. Use
non-color mild soap with warm water clean
spills(Mix 1:10 soap to water)
Do not place furniture under direct sunlight,
material will possibly fade over time.
Do not use on site dry Cleaning machine.
Children should not climb or jump on the
furniture.
Do not write on furniture without a padded
barrier to protect the surface.
Not for commercial use, For residential use
only.
Weight Limitation
80LBS
2/15

OVERVIEW
3/15

PARTS
LIST
4/15

PARTS
LIST
5/15

HARDWARE
LIST
Be sure to check all packing material carefully for
small parts, which may have come loose inside the
carton during shipment.
6/1 5
SPARE

ASSEMBLY
INSTRUCTIONS
7/1 5
Preparing part 1
1)Align the pre-drilled hole in part 1,
screw in the cam bolt A and tighten by
screwdriver T。
2）Align the hole in part 1 as the
picture show, screw in the part O by
hand.
Connect part 3,4,5,6 to the part 1
1) Align the hole in the part 1, insert the part D into the hole by hand;
2) Align the hole in part 3, insert the part D and cam bolt A at the same
time, then put nut B and tighten by screwdriver T
3) Cover the nut B by part J for good looking.
4) Repeat the same way to finish part 4, 5, 6.

8/1 5
Install part 2
1) Align the hole in part 3,4,5, insert the part D by hand;
2) Align the hole in part 2, insert the part D into the part 2 at the
same time, then
3) Align the the hole in part 2 to the hole in part 3,4,5,6, screw in
the screw C and fully tighten by Allenkey K.
Install part 8
1) Align the groove in part 4, 6 and 1, insert part 8 into the groove and
slide down to the end. be sure the part 8 in the groove of part 1.
2) Repeat the same way to finsih the rest of part 8.
1
6

9/1 5
Connect the part 9 to part 10
align the hole in part 10 to the hole in
part 9, screw in the screw G and
tighten by Allenkey K.
Assemble legs(part 11)
Align the hole in part 9 to the hole
in the part 11, screw in the screw
F and tighten by Allenkey K.
Do not fully tighten at this step!

10/1 5
install the leg frame(finished part in step 6)
align the hole in part 9 to the hole in part 2, screw in the ALL
screw F(including not fully tighten in step 6) and fully tighten by
Allenkey K in sequence.
Assemble part Q and part L
1) Align the hole in part Q to the part 1, screw in
the screw E and fully tighten by screwdriver T;
2) Insert the part L into the space between the
part 1,2 and 3,4,6,8, align the hole in part L ,
screw in the screw E and fully tighten by
screwdriver T as the picture show.
4
1

11/1 5
Install part M
1) Align the pre-drilled hole in part 3,4,5, insert the part M into the hole( you have
3 options according to your expectation of height), but you must be sure they are
in the same level both left and right after you finished)
2)Seperately put the part 7 on the part M.

12/1 5
Prepare the part H and part N
1)Align the hole in part H to the pre-drilled hole in part 12, screw in the
screw E and fully tighten by screwdriver T;
2) Align the hole in part N to the pre-drilled hole in part 12, screw in
the screw E and fully tighten by screwdriver T;
3) Repeat the same way to finish part 15 with part H and N.
4) Align the hole in part H to the predrilled hole in part 3 and 4, screw
in the screw E and fully tighten by screwdriver T
5) you can adjust the door to fit the cabinet as the picture show.

13/1 5
Prepare the doors(part 13 and 14)
1)Align the hole in part I to the pre-drilled hole in part 13, screw in the screw
E and fully tighten by screwdriver T;
2) Align the hole in part N to the pre-drilled hole in part 13, screw in the
screw E and fully tighten by screwdriver T;
3) Repeat the same way to finish part 14 with part I and N.
4) Align the hole in part I to the predrilled hole in part 5, screw in the screw E
and fully tighten by screwdriver T
5) You can adjust the door to fit the cabinet as the picture show.

Install the anti-collapse device.
1.Mark the position on the wall, this should be same as the position of Q where
are on the back of panel 1; Drilled and insert the expandable screw S by
hammer;
2.Assemble the part Q on the wall screw in the screw P and tighten by
screwdriver T.
3.let the plastic belt R go through the both Q and pull to tighten.
Finish the Anticollapse device.
14/1 5
not provided.
Assembly Completed

Are you having difficulty
with assembly? Missing parts?
Please send email with your order No
[email protected]
For return, Please check the return policy with
the retailer or MarketPlace you bought from.
Appreciated your purchasing from us.
Pop up your life by our furniture piece!
15/15
WARRANTY
We strive to offer high-quality products, and we also try our
best to satisfy each and every customer that orders from us
with product or service as needed. We provide 30 days
warranty starting from the time you receive the item. Each
customer must provide a record of their order such as the
order number, or item receipt for any items that are out of
the warranty period you may also still receive replacement
parts by purchasing them with our company if they are
available.