HULALA HOME SCBSD0532 User manual

NOTE:
This brochure contains IMPORTANT safety info. Please read and keep it
for future reference.
1/16
ITEM NO. SCBSD0532

MAINTAINANCE
AND WARNING
Keep furniture away from heat sources.
Do not clean furniture with harsh cleaner or
polishes. Do not use detergents, Solvents,
abrasives, spray packs or leather cleaner. Use
non-color mild soap with warm water to
clean spills(Mix 1:10 soap to water)
Do not place furniture under direct sunlight,
material will possibly fade over time.
Do not use on site dry Cleaning machine.
Children should not climb or jump on the
furniture.
Do not write on furniture that is not
protected by a padded barrier .
Not for commercial use, only for residential
use .
Weight Limitation
70LBS
162

PARTS
LIST
163
13

Explosive View
164

HARDWARE
LIST
Be sure to inspect all packing material carefully for
small parts, that may have come loose inside the
carton during shipment.
165
SPARE
H
x12
Ax4
Dx8 x2
G
4*35mm
15mm
J
I x4
C x16
O
x18
M6*50mm
Px9
Ex8 x58
M6*35mm
x1
M6*35mm
M4
B
x2
8 *30mm
x8 F
Qx3 R
x2
x4
3.5*14mm
M7*50mm
x4 N
x8 MLK
3.5*14mm
x5 x1 x1
M6*35mm
M6*50mm
L
M7*50mm
x1 x1
4*35mm
Q
EPx1A
M6*35mm
C
x6
S
M4*18mm
x1
S
M4*18mm
x9
T
13
U

6 16
ASSEMBLY
INSTRUCTIONS
x8x8
M6*35mm
D
8*30mm
A
15mm
x8J B x8
A*8
D*8
1
13
6
J*8
4
5
B*8
Insert the wood dowel D into the holes of panel 1,then attach
the cam bolt A to panel 1 by screwdriver.
Use the screwdriver and cam lock B to connect panel 3,4,
5,6 with panel 1,make sure all holes aligned and tighten
all bolts to secure.Then stick the part J on all bolts
holes.
6
5

16
7
3
x8
D
K
M 7*50m m
M 4
x8
x1 C
1
9
4
10
9
2
4
8*30mm
D
9
10
9
1
Carefully align and slide the back panel 9 & 10 into the groove along rear
edge of pre-assembled unit in step 2,insert the wood dowel D into the
holes of panel 3,4,5,6.
Use the allen key K and bolt C attach the assembled step 3 with
panel 2,make sure all holes aligned and tighten all bolts to secure.

168
K
M6*50mm
M4
x1 x5 P
x4
Q
K P
M4
x1
M6*35mm
x2
M6*50mm
13
13
14
x5
T
13
x4
T
13
T*5
T*4
Use the allen key K,bolt P and flat washer T to connect
stretcher 14 with panel 2,make sure all holes
aligned and do not tighten all bolts until step 6.
Use the allen key K,bolt Q,bolt P and
flat washer T to connect the stretcher
14 with the left & right leg 13,make
sure all holes aligned and tighten
all bolts to secure.

9 16
x18x18
E
3.5*14mm
H
H*18
E*18
Use the screwdriver,screw E and plastic buckle H to connect the back panel
with all side panel & top panel, vertical partition panel,bottom panel. Then
fasten all screws to secure.

1610
8
I*12
I
Place shelf holders I into the desired position and then slide
adjustable shelves 7 & 8 into place.