Hunter Electronics GPS-DTR 25000 User manual

DOG TRAINING COLLAR WITH GPS TRACKER
MODELS: GPS-DTR 25000-25002-25003 (GPS and training function)
GPS 25000-25002-25003 (no training functioning)
PREPARING THE GPS-TRAINING COLLAR FOR FIRST USE
Charge the collar for7-8 hours. The battery has a standby time of 20 hours when fully charged.
Connect the small USB adapter to theUSB cable, and then the cable to the USB charger. Then con-
nect the charger to the collar 'as shown below picture. Lift the orange plastic protective cover and
connect the charger. Now turn on the collar. To switch it on, hold the back side close to the remote
control USB (where the built-in magnet is) for 1 second at the point where the collar indicator lamp
is located. Then remove the remote control. The red indicator light on the collar will continuously
indicate that the device is charging. In order to have full charge we need to TURN OFF the collar
with the remote control magnet durring the charging process
After 7-8 hours of charging, remove the charger. To switch off the collar, hold the remote control part
(where the built-in magnet is located) for 4 seconds at the point where the collar indicator lamp is loc-
ated.
The remote control should be charged for 4-5 hours.
Connect the charger to the remote control on the USB connector on the top.
PAIRING AND USE THE GPS-DOG TRAINING COLLAR
The training collar you purchased is already paired with its remote control. If you want to pair it again, follow the
instructions below. The remote control can control up to 9 collars. The remote control has + and - buttons for collar
selection in which to send commands Turn on the remote control from the ON / OFF button, then turn on the collar.
When the collar is lit the red indicator
light of the collar flashes. Press for 4-5 seconds the display light button will now flash the speaker icon on the
screen. The remote control is in tuning mode. Then hold the back of the remote control (where the built-in magnet
near the USB is located) for 10 seconds at the point where the collar indicator lamp is located. Remove the remote
control from the collar after 10 seconds and if you have heard 3 consecutive beeps from the collar, then press the
shock command button for 2 seconds. You will hear a beep, indicating that the sync was successful. Repeat the same
procedure if you want to sync other collars. When you have finished adjusting the collars, press the audio command
button to return the remote control to normal operation. When you press the remote control shockr button, a shock
command is sent to the corresponding collar. Each time you press the audio command or the push button or the
audio + shock button, the screen flashes, indicating that the command is being sent to the collar. The level of
excitement fluctuates with the increasing number of buttons on the remote control from 1 to 8. Level 1 is the lowest
and level 8 is the highest. After use, you can turn off the remote control using the ON / OFF switch.
the remote control to normal operation. When you press the remote control shockr button, a shock command is sent
to the corresponding collar. Each time you press the audio command or the push button or the audio + shock button,
the screen flashes, indicating that the command is being sent to the collar. The level of excitement fluctuates with the
increasing number of buttons on the remote control from 1 to 8. Level 1 is the lowest and level 8 is the highest. After
use, you can turn off the remote control using the ON / OFF switch.
INCLUDING Training Collar, USB Charger, USB Cable, USB Remote Antenna Adapter, Short and long spikes.
want to sync other collars. When you have finished adjusting the collars, press the audio command button to return
the remote control to normal operation. When you press the remote control shockr button, a shock command is sent
to the corresponding collar. Each time you press the audio command or the push button or the audio + shock button,
the screen flashes, indicating that the command is being sent to the collar. The level of excitement fluctuates with the
increasing number of buttons on the remote control from 1 to 8. Level 1 is the lowest and level 8 is the highest. After
use, you can turn off the remote control using the ON / OFF switch.
INCLUDING Training Collar, USB Charger, USB Cable, USB Remote Antenna Adapter, Short and long spikes.
INCLUDING
Training Collar, USB Charger, USB Cable, USB
Remote Antenna Adapter, Short
and long spikes.

TIPS FOR USING GPS-DOG TRAINING COLLAR
The remote control training collar is specially designed for hunting dogs and works under difficult conditions condi-
tions (rain, dense vegetation etc).
It is lightweight and durable and is ideal for both small and large large dogs. The training collar should be positioned
from the bottom of the dog's neck.
The two pins should be fastened the dog's skin so that it can feel the stimulus. Place it tight on the neck and if the dog is
long coat the hair slightly so that the pins make contact with the skin You need to find the right power level for your dog.
Start from level 1 and if you see no reaction Use the level 2. Increase the level until you see a reaction from the dog.
When the dog react then this is the level you need to use. If you use level 8 which is the highest and you see no reaction
from the dog then the collar has no properly placed on his neck. It should be tight and if the dog has long hair, trim it so
that the pins to make contact with the skin.
Use short or long pins depending on the dog's hair. Always be present during the charging process of the devices It is
recommended to charge one time per month during the period when we do not use the device and store it at all times.
Charged in a dry environment with temperatures below 40 degrees
We advise you to charge the collar and remote control before each use.
GPS TRACKER
The collar build in a GPS antenna and the remote control a Bluetooth module.
The remote control communicates with mobile phone or tablet via Bluetooth.
The mobile phone or tablet used must be Android 5.0 or later and Bluetooth version 4 or 5.
To synchronize the remote with your mobile, follow these steps:
1. Download and install the app on your mobile.
2. Turn on the remote control from the switch.
3. Start the application.
4. You will see the picture below (first). Select start scan and then tap the Bluetooth icon (second image) and you'll go straight to
the map.
5. You can see on the map a dog's head indicating the dog's position (the collar must be out and looking the sky).
6. By tapping the dog's head in the application you can see the distance between the user and the collar.
WARRANTY We offer 1 year warranty and fast service upon expiry. The warranty does
not cover the built-in rechargeable batteries