Hunter 20091209 User manual

OscillatingOscillatingOscillating
Form# 44830-01
20091209
©2009 Hunter Fan Co.
Stand Fan
Owner’s Manual
Model
90391
English

2©2009 Hunter Fan Co. 44830-01 20091209
TABLE OF CONTENTS
Introduction ............................................................. 3
Safety and Warnings................................................ 3
Unpacking............................................................... 5
Fan Assembly .......................................................... 5
Base Assembly......................................................... 6
Stand Fan 6
Height Adjustment 6
Table Fan 7
Wall Mount 7
Remote Battery Installation ........................................ 8
Operation - Fan/remote ........................................... 8
Maintenance............................................................ 9
Technical Support................................................... 10
Warranty............................................................... 10
Products ................................................................ 12

3©2009 Hunter Fan Co. 44830-01 20091209
INTRODUCTION
READ THIS ENTIRE MANUAL CAREFULLY BEFORE
BEGINNING INSTALLATION. SAVE THESE
INSTRUCTIONS FOR REFERENCE.
To reduce the risk of fire or electrical shock, DO NOT use
this fan with any solid-state speed control device.
When using electrical appliances, basic precautions
should always be taken to reduce the risk of fire, electric
shock and personal injury:
Read all instructions before using this fan.
1. Improper installation may result in the risk of fire,
electric shock or personal injury.
2. To prevent the risk of fire and electric shock, DO
NOT use the unit near windows. Rain and moisture
may create an electrical hazard.
3. The power plug must be removed from the power
socket when not in use, before cleaning, servicing,
maintenance and before moving to another location.
4. This product is intended for indoor use only. DO
NOT place fan in damp locations where humidity
is present.
Thank you for choosing the Hunter Oscillation Stand
Fan. This manual gives you complete instructions for
assembling and using your fan. Here are some the
features you will enjoy with your fan:
3An attractive design that enhances any decor
3A powerful motor for maximum air flow
3Three speeds to adjust your comfort level
3Remote controlled for added convenience
3Multiple oscillation settings
3Timed running mode.
3Parts of this fan, including the blades and the grill,
have been treated with Hunter’s Dust Armor protection,
making them less likely to attract dust and dirt.
SAFETY AND WARNINGS

4©2009 Hunter Fan Co. 44830-01 20091209
5. The fan should be placed on a flat, stable surface or
tabletop to avoid overturning.
6. Use fan only for intended use, as described in this
instruction manual.
7. To protect against electrical shock, DO NOT immerse
unit, plug or cord in water or spray with liquids.
8. Close supervision is necessary when any appliance
is used by or near children.
9. NEVER insert fingers, pencils or any other objects
through the grill when the fan is running.
10. DO NOT operate any appliance with a damaged
cord or plug, after the appliance malfunctions or has
been dropped or damaged in any manner.
11. To disconnect, grip plug and pull from wall outlet.
NEVER pull on cord to disconnect from outlet.
12. ALWAYS use on a dry surface.
13. This product is intended for household use only and
not for commercial or industrial use.
14. DO NOT operate fan in the presence of explosive
and/or flammable fumes.
15. DO NOT place fan or any parts near an open flame,
cooking or any other heating appliances.
16. DO NOT use near curtains, plants, window
treatments, etc.
17. Do not mix old and new batteries.
18. Do not mix alkaline, standard (carbon-zinc), or
rechargables (ni-cad, ni-mh, etc) batteries
19. This product conforms to UL STD 507 and is certified
to STD C22.2 No.113

5©2009 Hunter Fan Co. 44830-01 20091209
FAN ASSEMBLY
Figure 3.
Figure 4.
Figure 5.
1. Remove the Plastic Nut (2) from the fan motor housing
.Figure 3.
2. Set the Rear Grill (3) against the front part of the
Motor Housing with the handle facing up. The 3 pins
on the motor housing should stick through the back
of the Rear Grill. Figure 4.
3. Screw the Plastic Nut (2) onto the fan and tightenly
firmly. Figure 4.
4. Remove the Plastic Sleeve from the motor housing
shaft and discard.
5. Install the Fan Blade (4) by sliding it over the motor
housing shaft, lining up the cut-outs on the back of
the Blade with the Retaining Pins on the Motor shaft.
Figure 5.
6. Screw the Spinner (1) onto the shaft counterclockwise
until secure. Figure 5.
7. Open the clips on the Front Grill
8. Set the Front Gill (5) into the notch on the bottom
of the Rear Grill (3) So the Hunter logo is facing
rightside up. Figure 6.
9. Close the clips On the Front Grill to hold both Grill
pieces in place. Insert the grill screw on the top of the
fan grill and tighten securely.
(2) Nut
(3) Rear Grill
(2) Nut
(4) Fan Blade
(1) Spinner
Figure 6.
(5) Front Guard
UNPACKING
As you unpack the fan, save the carton and packing
materials in case you want to move or ship the unit in
the future.
Carefully remove all items from the box.
NOTE: It is best to have someone hold the box while
you lift the fan and the protective packaging out of the
carton.
Make sure all shipping materials are removed from fan
before operating.

6©2009 Hunter Fan Co. 44830-01 20091209
Stand Fan
Figure 9.
BASE ASSEMBLY
1. Slide the Telescope Rod (7) into the top of the Stand
Base (8) aligning the 4 screw holes. Figure 7.
2. Secure the Telescope Rod (7) by inserting the 4 base
screws(9) inot the 4 nuts placed on the bottom of the
fan base and tighten securely. Figure 8.
3. Remove the Adjustment Knob(10) by twisting
counter-clockwise and slide the Base Cover(11)
down the Telescope Pole(7) until it covers the Screws
at the Stand Base(8). Figure 9.
4. Reattach the Adjustment knob and tighten.
5. Loosen the Screw in the back of the Fan Assembly.
6. Slide the Fan Assembly onto the telescope pole of the
base until it rests on the top of the pole. Figure 10.
7. tighten the screw on the back of the fan Assembly
until secure.
Warning: Do not force pole into the Stand Base
as damage to the Telescope Pole may occur. Do not
overtighten the Base Nut or screws.
Figure 7.
(7) Telescope Pole
(8) Stand Base
Figure 8.
Height Adjustment
1. Grip the upper part of the telescope pole and loosen
the Adjustment Knob.
2. Raise or lower the pole to the desired height.
3. Turn the Adjustment Knob until it is secure.
When adjusting the height of the fan, always grip the
pole above the adjustment knob firmly to prevent the
telescoping pole from collapsing.
(9) Screws
(10) Adjustment
Knob
(11) Base Cover
Figure 10.

7©2009 Hunter Fan Co. 44830-01 20091209
OPERATION  FAN/REMOTE
Figure 12.
See Figure 12. for fan operation and Figure 13. for
remote operation.
ON/SPEED - Turns the unit on and adjust the speed of
the unit between High, medium, and low.
OSC - Sets the oscillation mode of the fan.
TIMER - Used to set the running time to 0.5 to 7.5 hours
in 30 min, 0.5 increments.
Note: The digital indicators on the fan will light up to
indicate the timer setting. 0.5 will light up for 30
minutes or 1H and 4H will light up to indicate 5
hours.
OFF - Turns the fan off.
0.5H 1H 2H 4H
L M H
ON l SPEED
TIMER
OFF
OSC
REMOTE BATTERY INSTALLATION
Figure 11.
1. Turn the Remote Control over and Remove the Battery
Cover from the back by gently pressing down on the
tab and sliding down on the tab. Figure 11.
2. Insert 2 “AAA” Batteries into the battery compartment,
ensuring the positive and negative ends of the
batteries are installed correctly.
3. Slide the Battery Cover back and snap into place.
SPEED
OSC
ON/OFF
TIMER
Figure 13.
L M H - Indicates the current running speed of the fan.
0.5 1H 2H 4H - Shows the number of hours the timer
is set to run.
- Fan oscillates from left to right.
- Fan oscillates up and down.
- Fan oscillates in a figure 8 motion.
FAN INDICATORS

8©2009 Hunter Fan Co. 44830-01 20091209
MAINTENANCE
This fan is permanently lubricated and will not require
additional lubrication (oil) for the life of the fan.
This fan requires little maintenance and contains
no user serviceable parts. DO NOT try to fix
it yourself. Contact qualified service personnel
if servicing is needed.
Before cleaning, turn fan off and unplug from electrical
outlet. Wipe off excess dust with a lintfree cloth.
To ensure adequate air circulation to the motor, keep vents
located at the rear of the motor housing free from dust
accumulation. A vacuum cleaner hose can be used to
clean these vents.
DO NOT immerse the fan in water or any other liquid.
CLEANING THE GRILL AND BLADE:
1. Turn the fan off and unplug from the electrical outlet.
2. Disassemble the grills by carefully lifting the latches
around the outer ring.
3. Remove the front grill.
4. The blade may be removed by turning the Spinner
Knob clockwise.
3Use a dry or slightly damp lint free cloth to clean
the fan. Do not use a furniture polish or any other
cleaners that leave any residue, as they will damage
the protective Dust Armor.
3DO NOT allow water or any other liquid to get into
the motor housing or base.
3Reassemble the fan after blades and grills have dried
completely.
3DO NOT plug the fan into an electrical outlet until it
has been fully reassembled.

9©2009 Hunter Fan Co. 44830-01 20091209
If you have any additional questions or problems with
your Hunter Portable Fan, please call:
USA: 1-888-830-1326
Canada: 1-866-268-1936
Hours of operation are from 7:00 am to 7:00 pm
Monday - Friday and 8:00 am to 5:00 pm on Saturday,
Central Time. You may also contact us over the Internet at
www.hunterfan.com.
TECHNICAL SUPPORT
1. Problem
3Fan will not oscillate.
Solution
3Push down on the knob on top of motor housing to
activate oscillation.
2. Problem
3Can not adjust the angle of the fan.
Solution
3Gentle grasp the grill of the fan and tilt up or down.
3. Problem
3Remote control will not operate.
Solution
3Remove the battery cover and confirm the batteries
are installed correctly according to polarity markings.
Warranty
WARRANTY
The Hunter Fan Company makes the following limited
warranty to the user or consumer purchaser of this Hunter
Portable fan:
If your Hunter Portable Fan motor fails at any time within
one year after the date of sale to you due to a defect in
material or workmanship, labor to repair the defect will
be provided free of charge at our nearest service center
or our Service Department in Memphis, Tennessee. You
will be responsible for labor costs after this one-year
period. The foregoing limited warranty applies only to
the motor itself, and does not apply to electronic controls

10©2009 Hunter Fan Co. 44830-01 20091209
Warranty
such as remote controls, remote control receivers or
transmitters used in conjunction with the motor. These
electronic control items are included in the one year
limited warranty below.
If any part of your Hunter Portable Fan other than the
motor fails at any time with one year after the date of
sale to you due to a defect in material or workmanship,
we will repair or, at our option, replace the defective
part free of charge for parts and labor performed at our
nearest service center or at our Service Department in
Memphis, Tennessee.
IF THE USER OR CONSUMER PURCHASER CEASES TO
OWN THE FAN, THIS WARRANTY AND ANY IMPLIED
WARRANTY WHICH THEN REMAINS IN EFFECT,
INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, ARE VOIDED. NO WARRANTY,
EXPRESSED OR IMPLIED, INCLUDING ANY WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE, IS MADE IN RESPECT TO THE GLASS GLOBES
OR LIGHT BULBS OR THE FINISH ON ANY METAL
PORTION OF THE FAN. THIS WARRANTY IS IN LIEU
OF ALL OTHER EXPRESS WARRANTIES. THE DURATION
OF ANY IMPLIED WARRANTY, INCLUDING, BUT
NOT LIMITED TO ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE, IN RESPECT TO ANY HUNTER FAN MOTOR
OR OTHER FAN PART, IS EXPRESSLY LIMITED TO THE
PERIOD OF THE EXPRESS WARRANTY SET FORTH
ABOVE FOR SUCH MOTORS AND OTHER PARTS.
This warranty is voided if your Hunter Fan is not
purchased and used in the USA.
This warranty excludes and does not cover defects,
malfunctions or failures of any Hunter Portable fan
which were caused by repairs by persons not authorized
by us, use of parts or accessories not authorized by
us, mishandling, improper installation, modifications,
or damage to the Hunter Portable fan while in your
possession, or unreasonable use, including failure to
provide reasonable and necessary maintenance.
To obtain servicing, contact the nearest Hunter authorized
service center or the Hunter Fan Company Service
Department, 7130 Goodlett Farms Pkwy. Suite 400,