Hunter 45062-01 Instruction manual

Type 3 Models
Type 3 ModelsType 3 Models
Form# 45062-01
20090701
©2009 Hunter Fan Co.
For Your Records and
Warranty Assistance
For reference, also attach your receipt or a copy
of your receipt to the manual.
__________________________________________
Model Name
__________________________________________
Model No.
__________________________________________
Date Purchased
__________________________________________
Where Purchased
English Español
Owner’s Guide and Installation Manual

2
45062-01 • 07/01/09 • Hunter Fan Company
Table Of Contents
1 • Getting Ready......................4
2 • Installing the Hanger Bracket .......5
3 • Assembling and Hanging the Fan . . . 6
4 • Setting the Remote Transmitter and
Receiver...........................7
5 • Wiring the Fan .....................8
6 • Installing the Canopy and Canopy
Trim Ring .........................9
7 • Completing Your Installation With
a Light Fixture.....................10
8 • Operating the Remote Control and
Mounting the Holder..............12
9 • Operating and Cleaning Your
Ceiling Fan ........................13
10 • Troubleshooting ..................14
© 2009 Hunter Fan Company
Your new Hunter® ceiling fan is an addition to your home or oce that
will provide comfort and performance for many years. is installation
and operation manual gives you complete instructions for installing
and operating your fan.
We are proud of our work. We appreciate the opportunity to supply
you with the best ceiling fan available anywhere in the world.
Before installing your fan, for your records and warranty assistance,
record information from the carton and Hunter nameplate label
(located on the top of the fan motor housing).
Cautions and Warnings
•READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING
INSTALLATION. SAVE THESE INSTRUCTIONS.
• Use only Hunter replacement parts.
• To reduce the risk of personal injury, attach the fan directly to the
support structure of the building according to these instructions,
and use only the hardware supplied.
• To avoid possible electrical shock, before installing your fan,
disconnect the power by turning o the circuit breakers to the
outlet box and associated wall switch location. If you cannot lock
the circuit breakers in the o position, securely fasten a prominent
warning device, such as a tag, to the service panel.
• All wiring must be in accordance with national and local electrical
codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a
qualied electrician.
• To reduce the risk of personal injury, do not bend the blade
attachment system when installing, balancing, or cleaning the fan.
Never insert foreign objects between rotating fan blades.
• To reduce the risk of re, electrical shock, or motor damage, do not
use a solid-state speed control with this fan. Use only Hunter speed
controls.
Welcome

3
45062-01 • 07/01/09 • Hunter Fan Company
Installer’s Choice and Optional Accessories
Understanding Mounting and Installer’s Choice®
Hunter’s patented 2-position mounting system provides you maximum
installation exibility and ease. You can install your Hunter fan in one
of two ways, depending on ceiling height and your preference: Standard
or Angled mounting. e steps in this manual include instructions for
both Installer’s Choice mounting methods.
Considering Optional Accessories
Consider using Hunter’s optional accessories, including a wall-mounted
or remote speed control. To install and use the accessories, follow
the instructions included with each product. For quiet and optimum
performance of your Hunter fan, use only Hunter speed controls.
For ceilings higher than 8 feet, you can purchase
Hunter extension downrods. All Hunter fans use
sturdy 3/4” diameter pipe to assure stability and
wobble-free performance.
Standard Mounting hangs from the
ceiling by a downrod (included).
Angled Mounting recommended for a
vaulted or angled ceiling
Support Brace
Standard
Mounting
Style
Ceiling
Outlet Box
Support Brace
Ceiling
Outlet Box
Angled
Mounting
Style
8
12
CAUTION: To reduce the risk of personal
injury, attach the fan directly to the support
structure of the building according to these
instructions, and use only the hardware
supplied.

4
45062-01 • 07/01/09 • Hunter Fan Company
To install a ceiling fan, be sure you can do the following:
• Locate the ceiling joist or other suitable support in ceiling.
• Drill holes for and install wood screws.
• Identify and connect electrical wires.
• Lift 40 pounds.
If you need help installing the fan, your Hunter fan dealer can direct
you to a licensed installer or electrician.
Gathering the Tools
You will need the following tools for installing the fan:
• Electric drill with 9/64” bit
• Standard screwdriver (magnetic tip recommended)
• Phillips-head screwdriver (magnetic tip recommended)
• Wrench or pliers
• Ladder (height dependent upon installation site)
Checking Your Fan Parts
Carefully unpack your fan to avoid damage to the fan parts. Refer to
the included Parts Guide. Check for any shipping damage to the motor
or fan blades. If any parts are missing or damaged, contact your Hunter
dealer or call Hunter Technical Support Department at 888-830-1326.
(In Canada, call 866-268-1936).
Preparing the Fan Site
Before you begin installing the fan, follow all the instructions in
the pullout sheet called “Preparing the Fan Site.” Proper ceiling fan
location and attachment to the building structure are essential for
safety, reliable operation, maximum eciency, and energy savings.
1 • Getting Ready

5
45062-01 • 07/01/09 • Hunter Fan Company
2-1. Drill two pilot holes into the wood support structure through the
outermost holes in the outlet box. e pilot holes should be 9/64”
in diameter.
Note: Your fan comes with four pre-installed neoprene noise
isolators.
2-2. read the lead wires from the outlet box down through the hole
in the middle of the hanger bracket.
2-3. Align the slotted holes in the hanger bracket with the pilot holes
you drilled in the wood support structure. For proper alignment
use slotted holes directly across from each other. If you are
installing the fan on an ANGLED ceiling, be sure to orient the
hanger bracket as shown in Illustration 2-3 (left or right view).
Note: e isolators should be ush against the ceiling.
2-4. Place a at washer on each of the two 3” screws and pass the
screws through the slotted holes in the hanger bracket into the
pilot holes you drilled.
Tighten the screws into the 9/64” pilot holes; do not use lubricants
on the screws. Do not over tighten.
Flat Washer
3” Screw
Steps 2-2 – 2-4
Hanger
Bracket
Isolator
Step 2-3 (Angled Ceiling Only)
OR
Ceiling Peak Ceiling Peak
Large
Opening Large
Opening
LEFT RIGHT
2 • Installing the Hanger Bracket

6
45062-01 • 07/01/09 • Hunter Fan Company
You can assemble your fan for standard or angled mounting as shown
in steps 3-1 – 3-3.
3-1. To assemble fan to hang down from a at or angled ceiling,
insert the downrod through the canopy, adapter cover grommet,
adapter cover, and canopy trim ring. (e adapter cover and
adapter cover grommet may already be attached to make one
piece.)
3-2. Feed the wires from the fan through the downrod.
Note: Make sure all the wires are on the same side of the metal
dowel pin inside the downrod.
3-3. Loosen the square head setscrew on the adapter to install the pipe
and ball assembly. Note: When the pipe and ball assembly is fully
installed, 2-3 threads on the pipe will still be visible; this is normal.
Securely retighten the setscrew with a wrench or pliers.
CAUTION: e adapter has a special coating on the threads. Do
not remove this coating; the coating prevents the downrod from
unscrewing. Once assembled, do not remove the downrod.
WARNING: Do not carry or lift fan by canopy.
3-4. Raise the fan and place the ball into the hanger bracket.
3-5. Align the notch on the ball with the indent in the hanger bracket.
(Rotate the fan until you hear the notch pop into place.)
Go to 4 • Setting the Remote Transmitter and Receiver.
WARNING: Fan may fall if not assembled as directed in these
installation instructions.
Steps 3-4 – 3-5
Indent
Steps 3-1 – 3-3
Downrod
Canopy
Canopy
Trim
Ring
Setscrew
Adapter
3 • Assembling and Hanging the Fan

7
45062-01 • 07/01/09 • Hunter Fan Company
CAUTION: e remote control device complies with part 15 of the FCC rules.
Changes or modications not expressly approved by Hunter Fan Company could void
your authority to operate this equipment.
Operation is subject to the following two conditions:
1. is device may not cause harmful interference.
2. is device must accept any interference received, including interference that may
cause undesired operation.
WARNING: Use only the Hunter Fan speed control supplied with this fan.
4-1. IMPORTANT! Before you change the DIP switch settings, make
sure the battery is not connected to the transmitter.
Change the position of the DIP switches in the remote transmitter
and the receiver. Make sure that the DIP switches match in
the remote receiver and transmitter. If they don’t match, the
transmitter will not function.
4-2. ere is a toggle switch beside the DIP switches on the transmitter.
Move the toggle switch toward the side that reads “CFL” if you are
going to operate the fan with CFL bulbs. Move the switch to the
“INC” side if you are going to use incandescent bulbs.
4-3. Install the included 9-volt battery into the transmitter.
Setting DIP switches
When two or more fans are located near each other, you may desire
to have the receiver/transmitter for each fan set to a dierent code,
so that the operation of one fan does not aect the operation of the
other fans.
e DIP switches for the receiver are located on the at surface of
the receiver. e DIP switches for the transmitter are in the battery
compartment.
Receiver DIP
switches
Transmitter DIP switches
4-4. Raise the fan and align the slots in the canopy with the hooks
on the ceiling plate.
Note: To hang the fan, you must tilt the canopy to an almost
vertical position so that the canopy slots sit on the ceiling
plate hooks.
CFL INC
Dip Switches
Set to 01110
Dip Switches
Set to 01001
Dip Switches
Set to 01110
Dip Switches
Set to 01001
Receiver 1 Receiver 2
Transmitter 2Transmitter 1
Example DIP Switch Settings
DIP Switches
Set to 0111
DIP Switches
Set to 0100
DIP Switches
Set to 0100
DIP Switches
Set to 0111
4 • Setting the Remote Transmitter and Receiver

8
45062-01 • 07/01/09 • Hunter Fan Company
5-1. Before attempting installation, make sure the power is still o.
5-2. To connect the wires, hold the bare metal leads together and place
a wire connector over them, then twist clockwise until tight. For
all these connections use the wire connectors provided.
CAUTION: Be sure no bare wire or wire strands are visible after
making connections.
5-3. Using a large wire connector, connect the ground wire from the
ceiling (grounding) to the green wire (grounding) from the ceiling
plate and the green ground wire from the downrod.
5-4. Using the large wire connectors, connect the white wire
(grounded) and the black wire (ungrounded) from the ceiling as
follows:
• e white (common) power wire (grounded) from the ceiling to
the white wire (grounded) from the receiver (marked on red tag
“NEUTRAL IN”)
• e black power wire (ungrounded) from the ceiling to the
black wire (ungrounded) from the receiver (marked on red tag
“LIVE IN”)
5-5. Using the small wire connectors, connect the wires from the fan as
follows:
• e black wire with a white stripe (ungrounded) from the fan
to the red wire (ungrounded) from the receiver (marked on
white tag “LIGHT OUT”)
• e black wire (ungrounded) from the fan to the black wire
(ungrounded) from the receiver (marked on white tag
“FAN OUT”)
• e white wire (grounded) from the fan to the white
wire (grounded) from the receiver (marked on white tag
“COMMON OUT”)
5-6. Turn the splices upward and push them carefully back through the
ceiling plate into the outlet box.
5-7. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the
outlet box.
Steps 5-3 – 5-5
Step 5-3
A • Ground/Green
Step 5-4
B • Ceiling Black
• Receiver Black: “LIVE IN”
C • Ceiling White
• Receiver White: “NEUTRAL IN”
Step 5-5
D • Fan Black with a white stripe
• Receiver Red: “LIGHT OUT”
E • Fan Black
• Receiver Black: “FAN OUT”
F • Receiver White: “COMMON OUT”
• Fan White
Receiver
A
B
C
E
F
D
Large Wire
Connector
Small Wire
Connector
All wiring must be in
accordance with national
and local electrical codes
and ANSI/NFPA 70. If you
are unfamiliar with wiring,
use a qualied electrician.
5 • Wiring the Fan

9
45062-01 • 07/01/09 • Hunter Fan Company
6-1. Partially install two canopy screws (about 2 full turns) in the
hanger bracket.
6-2. Raise the canopy over the hanger bracket. Align partially installed
screws with key slots in canopy.
6-3. Twist canopy clockwise to secure.
6-4. Install third & fourth canopy screw in round hole on canopy.
Securely tighten all four screws.
6-5. Using both hands, push the canopy trim ring up to the top of the
canopy.
6-6. Twist canopy trim ring clockwise to secure the canopy.
Should you need to remove the canopy
trim ring, follow these steps:
1. Twist canopy trim ring counter
clockwise until it releases from
canopy.
Steps 6-1 – 6-2
Canopy Trim
Ring
Canopy
Hanger Bracket
Step 6-3
Canopy
Screw
Step 6-4
Step 6-5
6 • Installing the Canopy and Canopy Trim Ring

10
45062-01 • 07/01/09 • Hunter Fan Company
Your Hunter fan comes with an integrated light xture assembly.
WARNING: Use only the light xture supplied with this fan model.
7-1. To attach the light kit top housing, partially install two
housing assembly screws into the light kit mounting plate.
7-2. Connect the upper plug connector from the motor to the
lower plug connector in the light kit.
Note: Both plug connectors are polarized and will only t
together one way. Make sure the connectors are properly
aligned before connecting them. Incorrect connection could
cause improper operation and damage to the product.
7-3. Align the keyhole slots in the housing with the housing
assembly screws.
7-4. Turn the light kit top housing counterclockwise until the
housing assembly screws are rmly situated in the narrow
ends of the keyhole slots. Install the remaining screw into the
housing. Tighten all three screws rmly.
CAUTION: Make sure the light kit top housing is securely
attached to the light kit mounting plate. Failure to properly
attach and tighten all three assembly screws could result in the
light kit top housing and light xture falling.
Housing
Assembly
Screw
Light Kit
Mounting
Plate
Light
Kit Top
Housing
Step 7-4
7 • Completing Your Installation With a Light Fixture