Hunter 90646 User manual

Tripod Fan
T
ripod FanTripod Fan
Owner’s Manual
English
Model
61811-01
R20220120
90646
T
T
T
T
T
r
r
r
r
T
T
p
p
od
i
p
i
p
o
o
dddd
po
od
Ow
ne
Owne
r
r
’
s
s
’
’

2
TABLE OF CONTENTS
Introduction ............................................................. 3
Safety and Warnings................................................ 3
Fused Plug............................................................... 6
Grounding............................................................... 5
Unpacking............................................................... 7
Fan Assembly........................................................... 7
8
9
Operation................................................................
8
8
Off / Speed Selection
Fan Tilt Adjustment
Maintenance............................................................
Technical Support.....................................................10
Troubleshooting .......................................................10
Warranty.................................................................10
61811-01 R20220120

3
INTRODUCTION
Thank you for choosing the Hunter Tripod Fan. This
manual gives you complete instructions for assembling
and using your fan. Here are some of the features you
will enjoy with your fan:
An attractive design that enhances any decor
Three speeds to adjust your comfort level
All metal construction
SAFETY AND WARNINGS
READ AND SAVE THESE INSTRUCTIONS! To reduce
When using electrical appliances, basic precautions
should always be taken to reduce the risk electric
shock and personal injury:
Read all instructions before using this fan.
1. Improper installation may result in the risk of
electric shock or personal injury.
2. To prevent the risk of and electric shock, DO
NOT use the unit near windows. Rain and moisture
may create an electrical hazard.
3. The power plug must be removed from the power
socket when not in use, before cleaning, servicing,
maintenance and before moving to another location.
4. DO NOT put fan in a damp place or where humidity
is high, such as a bathroom.
5. The fan should be placed on a stable surface to
avoid falling.
6. Use fan only for intended use, as described in this
instruction manual.
7. To protect against electrical shock, DO NOT immerse
any part of the unit in water or spray with liquids.
with any solid-state speed control device.
8. Close supervision is necessary when any appliance
is used near children.
61811-01 R20220120

4
9. NEVER insert pencils or any other objects
through the grill when the fan is running.
10. DO NOT operate any appliance with a damaged
cord or plug, after the appliance malfunctions or has
been dropped or damaged in any manner. Discard
fan or return to an authorized service facility for
examination and/or repair.
11. To disconnect, grip plug and pull from wall outlet.
NEVER yank on cord.
12. ALWAYS use on a dry surface.
13. This product is intended for household use only and
not for commercial or industrial use.
14. DO NOT operate fan in the presence of explosive
15. DO NOT place fan or any parts near an open
cooking or any other heating appliances.
16. DO NOT use near curtains, plants, window
treatments, etc.
17.
1.
2. Children should be supervised to ensure they do not
play with the appliance.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory, or
intellectual disabilities, and persons with lack of
experience, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
WARNING
This appliance has a grounded three-prong plug and
is suitable for grounded receptacle use only. An
adapter can be purchased separately for connecting
three-blade grounding-type plugs to two-slot
receptacles. The adapter must be properly grounded.
DO NOT attempt to defeat the purpose of this safely
feature.
18. Do not run cord under carpeting. Do not cover cord
with throw rugs, runners, or similar coverings. Do
not route cord under furniture or appliances.
will not be tripped over.
61811-01 R20220120

5
Figure 1
Fi 1
This appliance is for household use only and may be
plugged into any 120-volt AC electrical outlet (ordinary
household current). DO NOT use any other type of outlet.
This unit is suitable for grounded receptacle use only.
The power cord has a grounded plug as shown in
Figure 1, and must be used with an electrical outlet that
can accommodate the grounding pin. If your electrical
must purchase an adapter as shown in Figure 2.
NOTE: The adapters ARE NOT supplied with this fan.
Read, follow, and save the instructions that are included
with the adapter you choose. The green grounding lug
extending from the adapter must be connected to a
permanent ground such as a property grounded outlet
accommodate the grounding pin.
LINE CORD SAFETY TIPS
1. NEVER pull or yank on the cord or the appliance.
2.
3. To disconnect the appliance, grasp the plug and
remove it from the outlet.
4. Before each use, inspect the line cord for cuts and/
or abrasion marks. If any are found, the appliance
should be serviced and the line cord replaced. Please
return it to our Service Department or to an authorized
service representative.
5. NEVER wrap the cord tightly around the
appliance, as this could place undue stress on the
cord where it enters the appliance and could cause
it to fray and break.
6. DO NOT operate this appliance if the line cord shows
any damage, if the appliance works intermittently or
stops working entirely.
Grounded
Plug
Grounding Pin Grounded Outlet
Box Cover
WARNING
Figure 2
Fi
2
Grounded Outlet
Box Cover
Metal
Screw
Adapter
Grounding
Means
GROUNDING
outlet cannot accommodate the grounding pin, then you
box. Do not use an adapter if your electrical outlet can
61811-01 R20220120

6
Figure 3
Fi 3
This product employs overload protection (fuse). A blown
fuse indicates an overload or short-circuit situation. If the
fuse blows, unplug the product from the outlet. Discard
product if the attachment plug is damaged. To reduce the
remove, replace, repair or tamper with the originally
supplied plug. If the fan does not function properly, it may
be due to the safety device incorporated in this plug.
If the fuse fails, it is generally due to a short circuit or
circuit overload. Replace the fuse as per the instructions
below (follow product marking for proper fuse rating)
and check the product. If the replacement fuse
fails, a short-circuit may be present and
immediately unplug the unit and contact our
technical support department for assistance.
Fuse Replacement:
Grasp plug and remove from the receptacle or other
outlet device. Do not unplug by pulling on cord.
Locate the door on top of the plug. Figure 3.
2. Slide the door on top of the plug towards the blades.
Figure 4.
3. Carefully remove the fuse from the clips holding it on
with 5 Amp, 125 Volt fuse. Figure 5.
Warning! Electrical Hazard! Only replace with a
fuse type and rating matching what was removed from
a safety device (fuse) that should not be removed.
Discard product if the attachment plug is damaged.
the product. If the product fails a second time,
immediately unplug it and contact our technical support
at 1-888-880-3267.
4. Gently push the fuse back into the pins that will hold
it in place.
Note: If the fuse is not seated properly, the unit will not
function.
5.
6. Plug the fan back in and resume use.
FUSED PLUG
Figure 4
Fi
4
Figure 5
Fi 5
Slide the door back over the fuse box in the plug.
61811-01 R20220120
the top and bottom. RISK OF FIRE. Replace fuse only
RISK OF FIRE. Do not replace attachment plug. Contains

7
FAN ASSEMBLY
Figure 8
Figure 9
1.
UNPACKING
As you unpack the fan, save the carton and packing
Follow the steps below to attach the fan head to the tripod.
materials in case you want to move or ship the unit in the
future. Carefully remove all items from the box.
NOTE: It is best to have someone hold the box while
you lift the fan and the protective packaging out of the
carton. Make sure all shipping materials are removed
from fan before operating.
NOTE: It is
b
est to
h
ave someone
h
o
ld
t
h
e
b
ox w
h
i
l
e
you lift the fan and the protective packaging out of the
carton. Make sure all shipping materials are removed
f
rom
f
an be
f
ore operating.
Figure 7
Fully extend the pre-install tripod legs, align the holes
of the tripod bracket and the legs, install with three
position. (Figure 6)
2. Press the clip buttons in completely while sliding the
pole from the bottom pole assembly into the
pre-install tripod poles until the clip buttons appear
through the hole in the pre-install tripod poles. Place
4. Place the bolt cover from hardware bag onto the top
of the tripod bracket. (Figure 9)
3. Turn the fan head perpendicular to the fan head
slot of the tripod adapter, making sure the hole on
the fan head bracket align with the hole on the
tripod adapter. Take the bolt and nut from the
hardware bag, insert the bolt through the aligned
holes and tighten with the nut to secure the fan head
in position from the bottom of the tripod. (Figure 8)
61811-01 R20220120
Fan Head
Bracket
Fan Head
Nut
Bolt
Figure 6
Bolt Cover

Figure 11
OPERATION
Turn the fan “ON” or “OFF” by rotating the power/speed
knob at the back of the fan head. The power should
always be OFF before unplugging the fan. To select the
speed, turn speed control from OFF to the desired speed
setting: 0 (off), 1 (low), 2 (medium), 3 (high). (Figure 10)
Off / Speed Selection
Fan Tilt Adjustment
tilt the fan head manually to the desired angle.
(Figure 11)
61811-01 R202201208
0
2
3
1
Figure 10

MAINTENANCE
This fan is permanently lubricated and will not require
additional lubrication (oil) for the life of the fan.
This fan requires little maintenance and contains no user
serviceable parts. DO NOT try to x it yourself. Contact
qualied service personnel if servicing is needed.
outlet. Wipe off excess dust with a lint-free cloth. To ensure
adequate air circulation to the motor, keep vents located
at the rear of the motor free from dust accumulation. A
vacuum cleaner hose can be used to clean these vents.
DO NOT immerse the fan in water or any other liquid.
CLEANING THE FAN:
1. Turn the fan off and unplug from the electrical outlet.
2.
Use a dry or slightly damp lint-free cloth to clean
Use a soft, slightly damp cloth to wipe the remaining
fan parts.
DO NOT allow water or any other liquid to get into
the motor housing or base.
DO NOT plug the fan into an electrical outlet until it
has been fully reassembled.
the fan.
Before cleaning, turn the fan off and unplug from electrical
61811-01 R202201209

TROUBLESHOOTING
1. Problem
Cannot adjust the angle of the fan.
Solution
Loosen the screws on the side of the fan head bracket.
Adjust to the desired angle and tighten the screws.
W
W
W
WARRANTY
Hunter Home Comfort makes the following limited
warranty to the user or consumer purchaser of this Hunter
Portable Fan:
If any part of your Hunter Portable Fan other than the
motor fails at any time within one year after the date of
TECHNICAL SUPPORT
If you need any assistance with setup, operation, or parts
for your new Hunter Portable Fan, please call us. Our
technical support staff is ready to help! We are open
24 hours, 7 days a week.
You may also reach us online at
www.HunterHomeComfort.com.
An electronic copy of this user manual can also be
obtained online at www.HunterHomeComfort.com.
USA: 1-888-880-3267 (FANS)
[email protected]
10 61811-01 R20220120
If your Hunter Portable Fan motor fails at any time within
one year after the date of sale due to a defect in material
or workmanship, labor to repair the defect will be
provided free of charge at our Service Department in
Kennesaw, Georgia. You will be responsible for labor
costs after this one-year period. The foregoing limited
warranty applies only to the motor itself, and does not
apply to electronic controls such as remote controls,
remote control receivers or transmitters used in conjunction
with the motor. These electronic control items are included
in the one year limited warranty below.