HXM HD-007 User manual

HD-007 DIGITALDRUM
USER SMANUAL

CAUTION
Anychangesormodificationsinconstruction ofthisdevicewhicharenot expresslyapproved by
thepartyresponsibleforcompliancecouldvoidtheusersauthoritytooperatethe equipment.
WARNING
Whenusingelectricalproducts,basicsafetyprecautionsshouldalways be followed, including the
following:
NOTE:Thisequipmenthasbeentested and found tocomplywiththelimitsforaClass Bdigital
device,pursuanttoPart15 ofthe FCC Rules.
Also,thisequipmenthasbeentestedandfoundtocomplywiththe limitsforfollowing standard:
EN55022-2006
EN55024:1998/+A1:2001/+A2:2003
EN55013:2001/+A1:2003/+A3:2006
EN55020:2007
EN61000-3-2:2006
EN61000-3-3:1995/+A1:2001/+A2:2003
Theselimitsaredesignedtoprovidereasonableprotectionagainst harmfulinterferenceinaresi-
dentialinstallation. Thisequipmentgenerates,uses,and canradiateradiofrequency energyand,if
not installedandusedinaccordancewiththe instructions,maycauseharmfulinterferencetoradio
communications.However,thereisno guarantee thatinterferencewill notoccurinaparticular
installation. If thisequipment doescauseharmfulinterferencetoradioortelevisionreception, which
canbedeterminedbyturning the equipmentoff andon, the userisencouragedtotrytocorrectthe
interferencebyoneormoreofthefollowingmeasures:
-Reorient orrelocatethereceiving antenna.
-Increasetheseparation between the equipmentand receiver.
-Connectthe equipmentintoan outletonacircuitdifferentfromthattowhichthe receiveris
connected.
-Consultthe dealeroranexperienced radio/TVtechnicianforhelp.
CAUTION

TAKINGCAREOFYOURDRUM
-directsunlight (nearawindow),
-high temperatures(nearaheatsource,
outside,orinacarduringthedaytime),
-rainorexcessivehumidity,
-excessivedust,
-strong vibration.
wThe unit shall not beexposedtodripping or
splashing andno objectsfilled withliquids,
suchasvases,shall be placed onthe unit.
wThedrumcontainsdigitalcircuitryandmay
causeinterferenceifplacedtoo closeto
radioortelevisionreceivers.If interference
occurs, movethe drumfurtherawayfrom
theaffected equipment.
POWER
wOnlyuseattached poweradaptor.
wTurnthe powerswitchoff when the drumis
notinuse.
wToavoiddamagetothedrumand other
devicestowhichit isconnected, turnthe
powerswitchesofall related devicesoff
priortoconnection ordisconnectionof
audiocables.
wTurnthepoweroff ifthemaincableofthe
adaptorisdamaged orthe instrumentis
spatteredwithliquid.
wDonot switchtheunit onand off inquick
succession,thisplacesan undue loadon
theelectroniccomponents.
wUnplug the ACpowercordduring anelectri-
calstorm.
wAvoidpluggingthe ACadaptorintothesame
ACoutletasapplianceswithhighpower
consumption,suchaselectricheatersor
ovens.
SERVICEANDMODIFICATION
Thisproductshouldbeserviced byqualified
servicepersonnelwhen,
wthepowersupplycordortheplugofthe
adaptorhasbeendamaged,
wliquidhasbeenspatteredintotheunitorithas
been exposedtorain,
wthe instrument doesnot appeartooperate
normallyorexhibitsamarked changein
performance,
wthe instrument hasbeendroppedorthe
cabinethasbeendamaged.
HANDLINGANDTRANSPORT
wNeverapplyexcessiveforcetothe controls,
connectors,padsorotherpartsof the
instrument.
wAlways unplugcablesbygripping the plug
firmly,notbypulling on the cable.
wPhysicalshocks caused bydropping,
bumping,orplacingheavy objectson the
instrumentcan resultinscratchesand/or
moreseriousdamage.
wCarefullycheck theamplifiervolumecontrol
beforestating toplay. Excessivevolumecan
causepermanenthearing loss.
CLEANING
wClean the unitwithadryorlight-wet softcloth.
Donot usepaintthinnerorpetrochemical
basedpolishes.
LOCATION
wDonot exposethedrumtothefollowing
conditionstoavoiddeformation,discoloration,
ormoreseriousdamage,
DONOTATTEMPTTOOPENTHEUNITORMAKEANYCHANGEINTHECIRCUITSOR
PARTSOFTHEUNIT.
!

INSTALLATION ............................................1
SOUND MODULE ........................................5
Control Panel ................................................5
Back Panel ....................................................6
PLAYING PAD ...............................................7
DRUM KIT .....................................................8
SONG .............................................................9
Demo Song ...................................................9
User Song ....................................................10
METRONOME ...............................................11
Metronome ....................................................11
Tempo ...........................................................11
DRUM KIT EDIT ............................................12
Select kit for editing .....................................13
Enter the Edit Mode ....................................13
Select part to edit ..........................................13
Select parameter to edit ...............................14
Edit the parameter ........................................14
Edit another parameter or part .................14
Complete the edit ........................................15
SETUP ............................................................16
Accompaniment Volume for Demo ...........16
Percussion Volume for Demo .................. 16
Master Tune ................................................16
Advanced Parameter Edit ........................16
Sesitivity ............................................17
Dynamic Range ......................................17
Trigger Corve ..........................................18
Cross Talk ..............................................18
Hi-Hat Pedal setting ................................19
Reset ........................................................20
RECORD ....................................................21
Record ......................................................21
Save as a User Song ................................21
Erase User Song .......................................21
MIDI & USB .................................................22
VOICE LIST .................................................23
SPECIFICATIONS ........................................25
CONTENTS TABLE

INSTALLATION
Thedrawing showscompletedrumkitafteryourinstallation.
Poweradaptorandconnection cablesarenotshowninthedrawing.
1
CRASH
TOM1
TOM2
HI-HAT
RIDE
TOM3
KICK
SNARE
HH-CTRL
SOUNDMODULE

INSTALLATION
2
You can find all of these components in package for rack system installation..
Pad clamp
Rack clamp
L-Rod
Arm
Leg
Cymbal rod
Foot
Cross beam
Cymbal rod clamp
Wing nut

INSTALLATION
RACKSYSTEMINSTALLATION
1Open the arns,adjust theposition
ofarmsand cross beam, then
tighten the winnuts.
2
3
Installtherightandleftfoot,
adjusttheheighttohavethefeet
firmlyfixed ontotheground,then
tighten the winhuts.
4
Moveandrotateallthe
clampstoproper
location,thentihgtenthe
wing nuts.
5
Rotatethe L-rodstoproper
positions,thentightenthe
wing nuts.
Insertthe cymbal
rodsandadjusttheir
position.
3

INSTALLATION
4
1. Remove the wing nut, washer and felt pad
2. Put the cymbal pad into the rod along with parts removed in
step 1. Fasten the wing nut modertly to give the pad a little
bit wobbling like the real acoustic cymbal.
Crash and Ride have dif ferent part numbers.
Please refer to indication on page 5.
3.Adjust the angle of the rod then tighten the wing nut.
1. Insert the snare into the
L-Rod, then tighten the
wing nut.
2. Adjust the angle of the
L-Rod then tighten the
wing nut in the clamp.
Snare Installation
1. Insert the tom into the
L-Rod, then tighten the
wing nut.
Note: All the toms use the
same pad.
2. Adjust the angle of the L-Rod before
tightening the wing nut in the clamp.
Tom Installation
1. Align holes in the kick stand with
these in the bracket then fasten them
with screws.
2. Insert tongue of the kick stand into slot
of the pedal . Tighten the wing nut on
the pedal level to fix it.
Kick Installation
COMPONENTS INSTALLATION
1. Align holes in supporting board with these in sound
module then fasten them with screws.
2. Insert rod of the supporting board into the clamp,
then tighten the wing nut.
Sound module Installation
Please refer to the SOUND MODULE Chapter for electronic connection.
Electronic Connection
Finalizing the Installation
Adjust arms, clamps and rods to the best position you like to finalize the installation.
2
1
3
2
1
3
2
1
3
Cymbal Installation
Note:

(1) DISPLAY:The screen displays suchaskit number, namesand otherinformation.
(2) POWER: TurnsON/OFF the sound module.
NOTE: Whenyou turnthe poweroff, do not turniton immediately.Waitat least fivesecondstoturn
the poweronsothat the electroniccircuitscan properlyreset.
Thesoundmodulewillshutdownautomaticallyif thereisnooperation in20minutes,inordertosave
energy.Todisablethisfunction, poweronthemodulewhilepressingon snarerim.
(3) HEADPHONEVOL: Rotatethisknobtoadjust theoutputlevelofheadphone andlineout.
Rotateitclockwisetoincreasevolume.
(4) EDIT:Press thisbutton toconfiguredrumkits.
(5) SETUP:Press thisbutton toedit systemparameters.
(6) MODE:Press tochange theplaying mode fordemosongs.
(7) CLICK:Switchandsetup themetronome.
(8) TEMPO: Changethespeedof metronomeanddemosongs.
(9) KIT: Press toselect kits.
(10)DEMO: Press toplaydemosongsandusersongs.
(11)ENTER:Toconfirmoperation orentersubmenu.
(12)SCROLLWHEEL:Rotatetochangevalue,kit, ordemo. Pressthisbuttontoadjust master
volume.
(13)EXIT:Tocanceloperation orback torootmenu.
(14)Recordbutton: Pressit torecordusersongs.
(15)Playand stop button.Press tostop playingcurrent song orrecording. Fordetails, please
refertorelatedchapter.
(16) ¨PADBUTTONS: Ineditmode, press thesebuttonstoselect and listen tothe corresponding
pad.
SOUNDMODULE
CONTROLPANEL
5
1
23
4567 8
911 12
10 13 14 15
16

BACK PANEL
(1)HEADPHONE:This is theheadphoneoutput ofthesound module. Connect a1/8"TRScable
tothis output.
(2)LINEIN:Analog inputsocketofthe sound module,1/8"TRS. Anextra1/8"maletomale cable
will beneeded if youwant connect yoursoundmoduletoanysoundsource such as iPod, CD
player,mobilephoneorcomputer.Play and practice withyourfavoritemusic.
(3)-(4)L/MONO, R: Lineoutput ofthesound module.Connect thisoutputtoany amplifierusing 1/
4”TScable. Whileusingsingleamplifier,please connectL/MONOonly.
(5)TRIGGER:Triggerinputs socket ofsound module.Connect the multi-triggerconnector(AKA
25pinconnector)tothis socketand lock it. Theretagson all cables. Connect all cablestotheir
instrumentaccording totheirtags.
(6)USB:Connect standardBtype USB cabletothissocketfor,gaming,recording MIDI and using
plug-ins formoresoundoncomputer.
(7)DC 9V:Connect the included DC9Vpoweradaptertothis socket.
SOUNDMODULE
6
LINEINHEADPHONE L/MONO R TRIGGER USB DC9V
12345 6 7

PLAYINGPAD
7
TURNONTHEPOWER
(1)Turndowntheexternal audio deviceconnected
withthe drum.
(2)Pressthe POWERbutton while don¡¯t strikepad
orpress theHi-Hat control pedal.
(3)Turnon externaldevicesconnected.
(4)Strikethe pad and adjustthevolumetoaproper
level. PLAYING PADS
PlayingSnareDrum
Strikethe central position (head)of the pad tomake
headsound, strikethe rimofthe pad tomakearim
sound.
Playing Cymbal
Strikerubberareaof thecrashand ridepadtocreate
acymbal sound.
The crashhaschokefeature. Strikethe
crashpad,itssound will sustain.Squeeze
theedge portion,thesound will bemute.
All padshavestriking forcesensitivityfeature.
Strikethe pad hardertomakeahighervolumeand
strikethepadsoftertomakealowervolume.
Playing TomDrum
Strikethecentralposition tocreateasound.
PlayingHi-Hat
(1)StriketheHi-Hat pad withoutpressingthe Hi-Hat
control pedal tomakeanopenHi-Hatsound.
(2)StriketheHi-Hatpad whilefullypressing the Hi-
Hat controlpedal tomakeacloseHi-Hat sound.
(3)Strikethe Hi-Hat padwhilepressingtheHi-Hat
controlpedal gradually,the consecutiveopensound
changestoclosesound.
(4)Pressthe Hi-Hatpedaldown quicklytomakeHi-Hat
pedalsound.
Playing KickDrum
PresstheKickdrumpedaltomakeakick drum
sound.
RotatetheMASTERVOLUMEknob toturnthe
mastervolumeup/down. Rotatethe knob clock-
wisetoincreasethe volume;rotatethe knob
counter-clockwisetodecreasethe volume.
MASTERVOLUME
Head Rim

automatically while the KIT button indicator
will light up. The kit number and its name
will be displayed.
In some other operation modes, you may
press the KIT button to enter the kit select
operation mode.
PRESET KIT
The kit number is ranged 01 - 50.
Rotate the SCROLL WHEEL to select a kit
you desire. Rotate the knob clockwise to in-
crease the kit number and anticlockwise to
decrease the kit number. All preset kit num-
ber and name are listed in the KIT LIST.
USER KIT
You can create your own user kit by edit
function. Click the KIT button repeatedly will
switch the Preset Kit and User Kit selection.
The User Kit number is U01 - U10.
Rotate the SCROLL WHEEL to select an
user kit you desire. Rotate the knob clock-
wise to increase the kit number and
anticlockwise to decrease the kit number.
The factory setting for all User Kits is Uni-
versal Kit. You could call them even if you
don’t create your own user kit. Of course,
you could replace it by editing. Please see
<EDIT> Chapter in this manual for details.
Press the KIT button again to back to the pre-
set kit.
DRUM KIT
There are 10 preset drum kits and 10 User Kits. The kit is combination of different instrument voice
assigned to each pad which has unitary style for performance. All the kits are for your choice. Any
kit could be edited and saved as your own User Kit. After power, it’ll enter the kit selection mode
8
User kit mark User Kit number User Kit name
Preset kit mark Kit number Kit name
ROCK
UserKit01
1 ROCK
2 FUNK
3 POP
4 METAL
5 JAZZ
6 LATIN
7 TECHNO
8 80s
9 DIRTYSOUTH
10 DRUMSTEP
KIT LIST

(2) Practice with Demo Song
Youmaypracticeyourownperformancewith
thedemosong.
Therearethree modesforyourpractice:
FULL-Whenpressthebutton,youwill
hearcompletesong
DRUMONLY-When press thebutton,
you will heardrumsound only. It helpsyouto
getideahowtoperform drum.
DRUMMUTE-Whenpress the button,
you will hearbackground musicwithout drum
sound.Then,you can playdrumsbyyourself.
Press the MODE button repeatedlytochange
themode.
Tip: Volumeofthe backgroundmusicand
drumofthedemosongisadjustable
separately.Pleasesee ChapterSETUPfor
moreinformation.
1.DEMO SONG
(1) Select and Play Demo Song
Thereare52demosongsbuiltin.
Pressthe DEMO buttononcetoengage the
demosongmodewiththe indicatorlighting.The
displaywill show “All Demo”.Press the
button immediately,all demosongswillplay
onebyone.Ifyou don tselectsong,after3sec-
ondthe firstdemosong numberand namewill
appearonthe display.
Toselectasongyou desire,rotatethe SCROLL
WHEE tochooseasong.
Thenpress the buttontostartplay; the
buttonindicatorlightsup.
Whenselectsinglesong,it ll be played
repeatedly.
Whenthedemosongisplaying,pressthebutton
againtotostopthe playing,theindicatorturns
off.
SONG
Therearetwotypesof song.The demonstration song(Demo)isforyourenjoymentand practice.
Usersong isyourownrecorded song.
9
Demosong numberDemosongname
AllDemo
Drum Mute
ChaCha
Demosong tempo Demosong beat

2.USERSONG
Thereare10Usersongsinmaximumrecorded
byuser.
Pressthe DEMO buttontwicequicklytoengage
theUserSong modewiththeindicatorlighting.
Thedisplaywill show “All U-Song”.If you don t
selectsong,after3second thefirstavailable
usersongnumberandnamewillappearonthe
display.
If you want toselect asong you desire, rotate
the SCROLL WHEEL tochooseasong.
Then press the button tostartplay;the
buttonindicatorlightsup.
When theusersong isplaying,press the
buttonagaintotostop theplaying,theindi-
catorturnsoff.
Note: If theintervalbetween the firstand sec-
ondpressingofthe DEMO button islongerthan
2seconds,itllturntoKit modeinsteadofSong
mode.
Note: Ifyoudidntrecordanysong,thedisplay
will show“Nou-song”.After3second,themode
willchange toKitselectautomatically.
SONG
Tip: You mayeraseUserSong intheUserSong
mode.Pleaserefertothe <RECORD>chapter
intheManualfordetails.
3.EXITTHESONG MODE
Youmaynotedthatpress theDEMObutton once
toenterthe Demomode; pressthe DEMO but-
ton twicequicklytoenterthe Song mode.
Therefore,inthe Demo/UserSongmodepress
the DEMO button againtoexit the Demo/User
Song mode and turntothe Kitselection mode.
The DEMO indicatorturnsoff.
Or,you cansimplypress the EXITbuttontostop
palying , exitthe Demo/Song modeand turnto
theKitselection mode.
10
Usersong numberUsersong name
All U-Song
No u-song
User Song
度 拍号

METRONOME
1.METRONOME
Pressthe CLICK button tosoundthe
metronome. Press the button againtostop it.
Press the CLICK buttontwicetosetupthe
metronome.
(1) Time Signature Setting -Atfirst, you
couldsetthe timesignature.The the current
timesignaturewill blinkinthe secondrowof
the display.Rotatethe SCROLL WHEEL to
changethetimesignature.Availabletime
signatureis1-8/2,1-8/4,1-8/8, 1-8/16,The
defaultsettingis4/4. Press the ENTER button
toconfirmyousettingandturntothenext
parameterofthemetronome.
(2) Metronome Volume Setting -Afterpress
the ENTER buttontofinishthetimesignature
setting,thenextparametertosetupismetro-
nomevolume.Thedisplaywill show “Metro
Vol”andcurrentvolumeisblinking. Rotatethe
SCROLL WHEEL tochange the volume
ranged0-127,The defaultsettingis96.
Press the ENTER buttontoconfirm you
setting andturntothenextparameterofthe
metronome..
Youcan press the EXIT buttoninanystepto
exitmetronomesetting.
Duringthesetting,the metronomewillkeep
sound.
11
2. TEMPO
Pressthe TEMPO button,the currenttempo
valuewillblinkinthedisplay.Rotatethe
SCROLLWHEEL tochange thetempo
ranged 40-240.
Press the ENTER buttontoconfirm you
setting.
Afterabout 10 seconds,thisoperationwill exit
automatically.Or,press the EXIT buttonto
exitthetemposettingimmediately.
Time-Sig
Tempo
MetroVol
Timesignature
Tempo

DRUM KIT EDIT
12
A drum kit consists of drum pads, cymbals pads and Hi-Hat pedal physically.
They generate sound in different way such as by striking head or rim of drum pad, triggered by
striking Crash bow or edge, pressing Hi-Hat pedal. We call the source to generate sound as Part.
Each part is identified on the display by the icon with mark. The icon refers to part of striking head
of pad and cymbal is shown below. H.PDL refers to sound generated by pressing the Hi-Hat pedal.
HIHAT refers to Open Hi-Hat sound generated by striking the Hi-Hat cymbal.
Alternative part of the same instrument is shown by extra mark under the icon. For example, the
part generating sound by striking the Rim 1 of the snare is marked by an arch under the SNARE
icon.
Each part has multi parameters to create its characteristics such as voice, volume, reverb level and
Pan etc. The detailed description is listed In the table below.
The edit feature is to set parameter for each part, partly or for all parts in a kit. the Edit feature
makes it possible to change the currently selected drum kit setting. In this way, you may create
your own drum kit and save it as UserKit.
Snare Rim Edge of CRASH HI-Hat Close
PARAMETER DESCRIPTION EDIT RANGE
VOICE Voice assigned to the part 1 –275
VOLUME Volume of the part , 127 refers to the highest volume 0~127
PAN Stereo pan of the part. -64 refers to the most left, 63
refers to the most right, 0 refers to the center position -64~63
PITCH Pitch of the part. -10 refers to the lowest and 10 to the highest pitch. -10~10
REVERB Reverb effect level of the part, 127 refers to the highest level 0~127

The edit procedure is the same for every parameter, Assigning voice to the part is one of the most
important function. After you are familiar with the operation of voice assignment; it’ll be easy to edit
other parameters. The following section is the edit procedure taking example how to change voice
for a pad.
DRUM KIT EDIT
13
A simple way to select part is to hit area of the
pad you desire directly. This is an aternative
metrod of pressing the button.
Edit icon
Kit number
Part for editing
2. Enter the Edit Mode
Press the EDIT button to engage the edit mode.
the display will show the kit number for editing
and the EDIT icon appear.
3. Select part to edit
Press a select button to engage editing for this
part while the corresponding icon will blink. Some
instruments have two or more parts, for example,
the ´crash has bow and edge; Hi-Hat has open
and close etc. Press the button twice to select
alternative part of this instrument, correspond-
ing icon with the mark under the icon will flash.
Please refer to table below.
Voice
Edit Mode
PART DESCRIPTION ICON
Snare Rim1 Snare Rim1
Snare Rim2 Snare Rim2
Tom1 Tom1 Head
Tom2 Tom2 Head
Tom3 Tom3 Head
Kick Kick Drum
PART DESCRIPTION ICON
HH Pedal Hi-Hat Pedal
HiHat Open Hi-Hat Open
HiHatClose Hi-Hat Close
Crash Crash Cymbal Bow
Crash Edge Crash Cymbal Edge
Ride Ride Cymbal
Ride Edge Ride Cymbal Edge
Snare Snare Head
1. Select kit for editing
Select a kit for editing in the same way ex-
plained in the DRUM KIT chapter. The display
shows the kit number and kit name.
Item for editing
R IDE

DRUM KIT EDIT
5. Edit the parameter
The current contents of this parameter will blink.
In this example, it is the voice number. Rotate
the SCROLL WHEEL to change contents of the
parameter. In this example, you’ll change voice
assigned to Snare rim. Any parameter has its
own range to set. For example, there are 275
voices can be selected to assign to a part.
Please see Appendix VOICE LIST for details.
Press the ENTER button to confirm your setting.
Then, it’ll return to the parameter selection op-
eration stage.
6. Edit another parameter or part
Now, the parameter (the VOICE in this example)
editing for a selected part is finished. You may
continue to edit other parameters in this part or
change part to edit.
(1) Edit other parameter in the current part
After you press the ENTER button to finish cur-
rent editing, it’ll turn back to the parameter se-
lection stage with the next parameter blinking.
Press the ENTER button to edit this parameter
or select other parameter by rotating the
SCROLL WHEEL. Then, edit parameters in the
same way explained in the Step 4 - Step 5 above.
Parameters can be edited are listed in the table
in page 12.
Volume
4. Select parameter to edit
After select part, the current parameter will be
blinking . Rotate the SCROLL WHEEL to se-
lect a parameter to edit. In this example, select
VOICE. The default parameter is VOICE.
Press the ENTER button to confirm you choice.
Voice
xRock
14

DRUMKITEDIT
(2) Edit another part
Selectanotherpart toeditinthe samewayex-
plainedinPage 13.The currentparameterto
editwill keepno change.It providesyoueasy
methodtoeditthesameparameterforeachpart.
15
7.Completetheedit
Afterfinishall editingjobforthecurrentdrumkit,
youmayterminatethe edit.
Pressthe EXIT button, “Saveit?”.Then,you
havetwochoices:
(1)Saveediteddrumkitasyourownuser
kit:
Pressthe ENTER button. “UserKit”withUser
kitnumberblinkingwillappear.Rotatethe
SCROLL WHEELtochoosenumber,thenpress
the ENTER buttontoconfirm.
Note: Thereare10 built-inpreset UserKit. All
of themarethesameasKit01.Whenyousave
yourownUserKit, it llreplacethe existing one.
If the savingissuccessful,it llturntothe Kit
selectmode.Theindicatorsofthepadselect
buttonand the EDIT buttonwillturnoff.
Thedisplayalwaysasks “Replaceit”?.Press
the ENTER button toreplaceexistingone with
yournewediting. Pressthe EXIT buttonthen
changeanothernumber.Ifyoureallydontwant
tocoveranyexisting UserKit, press the EXIT
buttonagain,and itwillcoverthecurrent edited
kitthen turntotheKitSelectmode. .
TheUserKitsetting isnonvolatileeventhe
powerturnsoff.
(2)Press the EXIT button toexittheeditmode
andreturntotheKitSelection modewithoutsav-
ingasUserkit. The indicatorsof thepadselect
buttonand the EDIT buttonwillturnoff.
Theeditedresultswillcoverthe currentdrum
kitandactivateimmediately. Whenthepower
turnoff, thischangeswill reset.
Tip: Youmayresetthekit changesbyReset
feature.Pleasesee<SETUP>chapterinthis
Manualfordetails.
Saveit?
Replace it
UserKit

SETUP
IntheKitSelectionorDemo/Songstage,
pressthe SETUP buttontoentertheSetup
mode and itsindicatorlightsup. The param-
etertobesetupwill blink.Rotatethe SCROLL
WHEEL toselectone ofthe 7itemslisted
below,then pressthe ENTER toconfirmand
itscurrent value will bedisplayed.
Intheitemselection stage,pressthe EXIT but-
tontoexit setupoprationandturntotheKit
Selection mode.
1.AccompanimentVolumeforDemo
Whenplaydemosong, you mayhearback-
groundmusicaccompanied.Adjustthis
backgroundmusicvolumebyparameter
AccompVol.Rotatethe SCROLLWHEEL
tochangethevolumeranged0-24. Thede-
faultsettingis7.
Pressthe ENTER button toconfirm andturn
tothenextparameter.Pressthe EXIT button
toexitand turntotheparameterselection.
2.Percussion VolumeforDemo
Whenplaydemosong,you mayadjustper-
cussion volume.Adjustthisvolumebypa-
rameterD.DrumVol.Rotatethe SCROLL
WHEELtochangethevolumeranged 0-24.
Thedefaultsettingis11.
Pressthe ENTER button toconfirm andturn
tothenextparameter.Pressthe EXIT button
tocanclecurrentedit andturnbacktothe
parameterselection.
Press the EXIT button toexitand tothepa-
rameterselection.
3.MasterTune
Thisparameteraffectssound pitchglobally.
Rotatethe SCROLLWHEEL tochangethe
mastertuningranged0to+/-50.Thedefault
Settingis0whichrefersto440HzatA4note.
Pressthe ENTER button toconfirmand turn
tothenextparameter.Pressthe EXIT button
toexitcurrentedit andturntothe parameter
selection.
16
4.AdvancedParameterEdit
Thepurposeofthedrumkiteditistochange
soundcharacteristics suchasvoice,volume,
panetc.Thetarget ofadvanced parameter
editisphysicalcharacteristicsof padsuch
assensitivity, triggercurveetc.
AccompVol
Accomp Vol
2
1
3
D.Drum Vol
MasterTune
Advanced