Hyco Handyflow HF05L User manual

This water heater must be installed (water and electrical installation), commissioned and
serviced by approved service technicians in accordance with these instructions.
Fig. 1
HF05L Hyco Handyow 5L
HF10L Hyco Handyow 10L
Point of Use Water Heater
Operating and installation instructions
Operating instructions 2
Technical data 3
Installation instructions 4
9182.01
276008

2
Operating instructions
for the user and for the installer
Description
The non-pressure HF05L and HF10L water
heater keeps 5 or 10 litres of hot water avail-
able for use at any preselected temperature.
Fig. 2 shows the time that it will take to reheat
the water should the entire volume be used
up.
• The water heater must not be
pressurized. Never block the tting
outlet and do not use a Perlator or hose
with jet controller.
• If the temperature is set higher than
45 °C, very hot water can ow immedi-
ately!
• Keep children and the disabled (physi-
cal/mental) away from this unit unless they
are supervised by a person responsible for
their safety or have been given instructions
on how to use it.
• Ensure that children do not adjust the
temperature (to a high temperature) on
the unit when playing -
Risk of scalding!
• We recommend the use of the tempera-
ture restrictor set by the engineer, unless
absolutely necessary otherwise.
• To avoid risk of accidental resetting of the
protective temperature restrictor in the
event of a fault, the unit must not be con-
nected via a timer switch.
If you experience kettling noises or a reduced
water flow it is likely that the unit needs
descaling.
While the system is heating up, water will drip
from the spout.
To select the temperature (Fig. 4)
1Control knob
= cold.This setting protects
your water heater against frost.
It does not protect your taps
and pipework.
E(60 °C) = Recommended energy-saving
setting. Minimal scale build up.
85 °C = Maximum temperature
setting.
2Indicator lamp. Illuminates during the heat-
ing-up process.
Fig. 3 shows the amount of warm water
that you can obtain by mixing cold water (at
15 °C) to the hot water in the HF05L and
HF10L.
Example:
with the thermostat control knob set at
65 °C, the HF05L can supply 10 Litres of
water at 40 °C, when mixed with cold water
at 15 °C.
Fig. 2
Fig. 4
Fig. 3
40 °C
45 l
40 l
35 l
30 l
25 l
20 l
15 l
10 l
5 l
0
HF10L
HF05L
40 °C 55 °C E 65 °C 85 °C
40 min
35 min
30min
25 min
20 min
15 min
10 min
5 min
0
HF05L
HF10L
40 °C 55 °C E 65 °C 85 °C
2
1
9183.01

3
100 mm
b
d
ei
h
a
70 mm
G ½
22 mm
Technical data
1Temperature selection knob
2Signal lamp
3Cold water inlet
4Hot water outlet
5Electric connection
6Mounting bracket
7Heating flange
Model HF05L HF10L
Nominal capacity 5 l 10 l
Design open
Weight 3.0 kg 5,1 kg
Heating power see unit rating plate
Voltage 230 V
Flow rate, max. 5 l/min 10 l/min
Protection to
EN 60529
IP 24 D
Connection line approx. 700 mm
Temperature setting
range (fully adjust-
able)
approx.
35 °C - 85 °C
Dimension
amm 230 275
bmm 263 295
dmm 140 200
emm 303 387
hmm 422 503
imm 119 116
Application:
Oversink, for one draw-off point.
For operation with ttings for open (non-
pressure) water heaters.
Fig. 5
7368.03
4
21
6
3
5
7

4
8021.01
COLD WATER INLET
Fig. 6
Fig. 7
Installation instructions
The installation, electrical connection and first
operation of this heater should be carried out
by a qualified installer.
The company does not accept liability for
failure of any goods supplied which have not
been installed and operated in accordance
with the manufacturers instructions.
These instructions should be kept for reference
by the owner of the appliance.
If this unit is exposed to static mains
water pressure, the water container
may start leaking and cause damage.
Installation and water connections
Make sure that no accessories are left in the
packing.
Use mounting template in the packing.
Please note the following when installing the
unit:
•The water heater must be installed vertical-
ly, with the inlet and outlet connections at
the bottom of the unit
(Fig. 5 and 6).
•The inlet tap should be fitted to the right-
hand connection (cold water inlet, Fig. 6).
•The spout should be fitted to the left-hand
connection (hot water outlet) (Fig. 6).
•Install in a frost-free environment.
•Do not restrict the outlet pipe. Do not
connect any aerators or hose with jet
control.
The spout also acts as a vent.
Only open-outlet ttings can be
used with this appliance. It should NOT be
used with standard taps.
Installation
An installation template is provided.
Position and fix heater to wall using mounting
bracket supplied observing water connecions:
Blue = Cold water inlet
Red = Hot water outlet.
NOTE -The water connections must
always remain at the bottom of the
heater. It cannot be turned upside down.
If you confuse the connections, the
water heater will not function, and
will cause damage!
8021.01
4992.01
24
22

5
Electrical connection
The water heater must be installed in accor-
dance with I.E.E Regulations.
Wiring diagram (Fig. 8)
1Earth cable connector
2Signal lamp
3Thermostat
4Safety thermal cut-out with reset function
5Heating element
* For voltage and current information,
please refer to the rating label.
Any excess cable can be stored in the com-
partment in the rear of the unit (Fig. 9).
The unit should be installed with a fixed cable
connection (spur point). An isolator with at
least 3 mm separation on all poles must be
used in the AC mains circuit.
Temperature limiting (Fig. 10)
Limiting the temperature can:
•reduce the risk of scalding,
•save energy
•reduce scaling
The temperature can be limited to 38 °C,
45 °C, 55 °C and 65 °C.
Fig. 10 key:
1Thermostat control knob
2Factory set position - 85 °C
3Limiting possibilities.
Warning!
This appliance must be earthed.
Commissioning
1. Open hot tap fully until flows free of bubb-
le.
2. Switch on and select temperature.
Risk of running dry!
A thermal cut-out is tted within
the appliance. If this operates for safety
reasons it can be reset by simply turning
off the electrical supply to the water hea-
ter. When the supply is switched on again
the thermal cut-out will have reset. If the
problem continues, fault nding should be
carried out by a qualied installer.
4752.01
Fig. 9
3
12
4745.03
Fig. 10
38
Fig. 8
8731.01
L N
L N PE
1/N/PE ~ 230 V
8731.01
1/N/PE ~ *
1
2
4
3
5

6
Handing over
Explain the function of the unit to the user,
in particular, draw his attention to the safety
instructions. Hand over the installation and
operating instructions to the user.
Maintenance
Applicable to all maintenance work:
• Disconnect unit from the mains supply.
• Disconnect cold water pipe from unit.
• Remove unit, drain via the cold and hot
water connection pieces and place on a
table.
To remove the casing (Fig. 11):
Pull off thermostat knob, remove screws.
On the under side, lower the locking
screws towards the inside by rotating
them counterclockwise or clockwise.
Swing open casing and remove. Untighten
the plastic band of the HF10L.
The unit is now accessible for all maintenance
work.
Exchange cable
If the electric cable has to be removed, the
plastic thread which holds the form plate must
not be removed!
Sensor positioning
HF05L
The thermostat sensor and the safety thermal
cut-out sensor in the HF05L are located in
different capillary tubes.The thermostat sen-
sor should be positioned in accordance with
Figure 12.
HF10L
The thermostat sensor and the safety thermal
cut-out sensor in the HF10L are located
within the same capillary tube and should be
positioned in accordance with Figure 13.
Descaling
Remove heating flange, remove coarse calci-
um with a piece of wood, immerse heating
element up to the flange plate into decalcitant.
Faults to be cleared by an
approved professional
If the thermal cut-out operates by
using the water heater normally, the
reason for the fault must rectied and the
thermostat must be replaced.
Environment and recycling
Recycling of obsolete appliances
Appliances with this label must not be
disposed off with the general waste.
They must be collected separately and
disposed off according to local regulations.
5135.01
4753.02
4754.01
Fig. 11
plastic band
HF10L only
8722.01 8721.01
200 mm
260 mm
130 mm
HF10L
Fig. 12
HF05L
Fig. 13/Afb. 13

7

CAP 276008/80608/1/8238· HD · Subject to errors and technical changes!
HYCO Manufacturing Ltd
Units 1&2, Calder Works
Methley Road, Castleford
West Yorkshire WF10 1NX
Tel: 0 1 9 7 7 5 1 7 5 5 5
Tel: 0 1 9 7 7 5 1 7 6 6 6
Manufacturing Ltd