HydroHoist HarborHoist 8800 Short User manual

1Rev. 07142020

2Rev. 07142020
At HydroHoist® we take pride in bringing the most advanced, easiest to use, and lowest maintenance boat li sys-
tems to the market. Installaon of the li is simple due to its lightweight design and ease of operaon.
The following pages contain step-by-step instrucons of the installaon and operaon processes.
The Medium series HarborHoist™ li takes between 10 and 20 man-hours to assemble on average depending on
the size and conguraon. Review all parts, hardware, and required tools before beginning assembly. Don’t forget:
safety rst.
If you have quesons, contact the Technical Support Team at 1-800-825-3379.
Legend:
Requires careful consideraon
WARNING: could cause harm or damage to the li, vessel, and user
INTRODUCTION
Lis must be installed by an approved HydroHoist® installer. Failure to comply will result in termina-
on of warranty and could cause injury to the user and damage to the li and vessel.
It is STRONGLY recommended that each installer read the manual before aempng an installaon.

3Rev. 07142020
PRE-INSTALLATION CONSIDERATIONS
Due to its size, the following determinaons must be made before installing a HarborHoist™:
• Locaon of li assembly (remote or on-site)
• Method of transport from assembly to launch site
• Equipment required to safely build, transport, and launch the li
• Contact points between bunks and the hull (consider strakes and other hull protrusions)
If you plan to build remotely and assemble the li before transport, rst determine the li’s minimum width from
Chart 1. State regulaons may require special permits and escorts for transportaon. Consider how to obtain per-
mits and the cost. Remotely building pre-sub assemblies and then compleng nal assembly at the launch site might
be logiscally simpler.
Other items to consider:
• Does the launch site allow commercial work?
• Do you need a permit to work and/or launch at the ramp or dock?
• Is there a me limit on dock use?
• How will you transport the li from the launch site to the install locaon?
• How much of the li can be preassembled and transported safely?
• Do you have equipment with the capacity to li subassemblies onto a trailer for transport to the launch site?
• Does the nal assembly locaon have equipment to hoist and launch the completed li?
• Is there level ground for nal assembly, or will some assembly occur in the water?
• Verify the slip width meets the minimum requirements of the li width, see Chart 1.
• See Chart 2 for a list of the required tools.
Working through these consideraons is the rst step in a successful build.

4Rev. 07142020
Chart 1: General Specicaon of the Li
*Size = Li Capacity in lbs. per Tank
3' x 8' x 3' = 3200
4' x 8' x 3' = 5000
Main Tanks = 1100
** B = 3 x 3 V square bent beam in 100" or 104"
*** This is the minimum the li can be for 4" of clearance per side
Standard V Hull Series *Tank Dimensions
Liing Size
Weight
of li
(lbs.)
# Main
Tanks
# Aux
Tanks Width Length Depth Hull Bunk Length
Minimum
Li Width
Possible
***Max Beam of
Boat @ Minimum
Li Width
Max Li
Width
8,800 Short 3600 613' 10' 2' 16' 11' 6" 8' 7" 12' 9"
12,000 4400 813' 8' 3' 20' 12' 2" 9' 4" 14'10'
12,000 Shallow 4400 813' 10' 2' 20' 12' 2" 9' 4" 14'
12,000 Wide 4500 813' 8' 3' 20' 14' 4" 11' 6" 16' 3"
15,000 4600 823' 8' 3' 20' 12' 2" 9' 4" 14'
15,000 Shallow 4600 823' 10' 2' 20' 12' 2" 9' 4" 14'
15,000 Wide 4700 823' 8' 3' 20' 14' 4" 11' 6" 16' 3"
18,000 4700 824' 8' 3' 20' 12' 6" 9' 8" 14' 5"
18,000 Narrow 4600 10 23' 8' 3' 28' 12' 2" 9' 4" 14'
18,000 Wide 4700 824' 8' 3' 20' 14' 4" 11' 6" 16' 3"
Liing Size
Max Beam
of Boat @
Max li
****Minimum
Slip Recommend-
ed
**Cross Beam
Used (inches)
Max Length Boat
Recommended
Water Depth
Req.
Overall
Length of
Li
8,800 Short 10' 34" + Vessel beam 84s 28' 31"+ Dra 16' 10"
12,000 11' 6" 34" + Vessel beam 100B 32' 43" + Dra 22' 6"
12,000 Shallow 11' 6" 34" + Vessel beam 100B 32' 31"+ Dra 22' 6"
12,000 Wide 13' 6" 34" + Vessel beam 126B 32' 43" + Dra 22' 6"
15,000 11' 6" 34" + Vessel beam 100B 34' ( 38 performance) 43" + Dra 22' 6"
15,000 Shallow 11' 6" 34" + Vessel beam 100B 34' ( 38 performance) 31"+ Dra 22' 6"
15,000 Wide 13' 6" 34" + Vessel beam 126B 34' ( 38 performance) 43" + Dra 22' 6"
18,000 12' 34" + Vessel beam 104B 34' ( 38 performance) 43" + Dra 22' 6"
18,000 Narrow 11' 6" 34" + Vessel beam 100B 40' 31"+ Dra 28' 2"
18,000 Wide 13' 6" 34" + Vessel beam 126B 34' ( 38 performance) 43" + Dra 22' 6"
**** This assumes you are using a rope mooring soluon. This measurement allows for a 4" space between the rub
rail of the vessel and walkway. If used with a pole mooring system add an addional 24" to the minimum slip width
to take into account this system. The addional 24” will allow for mooring on both sides of the li (12” per side).

5Rev. 07142020
Chart 3: Torque Specicaons
BOLT SIZE FOOT POUNDS OF TORQUE
1/4-20 5 FT. LBS.
5/16-18 9 FT. LBS.
3/8-16 16 FT. LBS.
7/16-14 26 FT. LBS.
1/2-13 35 FT. LBS.
9/16-12 47 FT. LBS.
5/8-11 76 FT. LBS.
Chart 2: Required Tools
5/16” Socket Wrench / Driver Drill / Impact Driver
7/16” Socket Wrench / Driver 7/16 Drill Bit (n-coated high helix 6” cut length
recommended)
9/16” Deep Socket Wrench / Driver Hammer / Rubber Mallet
3/4” Deep Socket Wrench / Driver Thread Sealant
7/16” Box End Wrench Gloves
9/16” Box End Wrench Safety Glasses
3/4” Box End Wrench Drill Wax
Taper Tool (to aid hole alignments) 18” Bar Clamps (3)
5/16” Hex Bit Socket

6Rev. 07142020
Chart 4: PARTS LIST—8800 Short
HH-8800 V-HULL STRAIGHT BEAM SHORT FRAME
Part Description Expected Qty
TANK ASSEMBLY
HH-3000 TANK- HARBORHOIST GEN 1.5 6
HH-2650 KIT BOX, HARBORHOIST GEN 1 MOD TANK SET 3
HH-2601 TOP PLATE - HH GEN 1 MOD- ALUMINUM 6
HH-LPL-1024 GASKET - TOP HARBORHOIST 6
HH-LPL-1028 GASKET - UNDERNEATH - HARBORHOIST 12
HH-LPL-1027 GASKET - BOTTOM - HARBORHOIST 12
HH-LPL-1026 BEAM STRAP - ALUMINUM - HARBOR HOIST 12
HH-LPL-1040 CHANNEL - SUPPORT HH - ALUMINUM 12
HH-LPL-1025 STRAP PLATE - ALUMINUM HARBORHOIST 12
CROSS BEAM
HH-LPL-1018 I BEAM - 84 IN. - 8800 HH 6
WALKWAY
HH-1428 WALKWAY PANEL - HARBORHOIST G1.5 29
HH-2515 SUPPORT-WALKWAY HARBORHOIST 6
HH-LPL-1034 BEAM - 48IN SPAN - ALUM. HH. 4
HH-LPL-1033 TUBE - SPACER, 3X3 ALUMINUM 4
HH-2525 END CAP- HH WALKWAY WITH DECAL 4
HULL PADS
1035105 ASSY HYH HARBORHOIST ALUM BUNK - 16FT 2
1035195 HARDWARE KIT - HARBORHOIST HULL PADS (1 PER TANK SET) 3
CONTROL
1035233 HarborHoist Triton 5 Valve Single Blower -110 volt 1
HH-2517 CONTROL STAND HARBORHOIST GEN 1.5 1
HHE-2655 KIT, HARDWARE, CONTROL HARDWARE HH 2018 1
3072517 HOSE - RUBBER 1-1/4 in. ID X 100 ft. - CUT 1
HH-2687 KIT, HARDWARE HOSE CLAMPS AND TEES, 6600 1
AUXILLARY (AUX) TANKS
HHE-7122 I-BEAM - SINGLE AUX TANK MOUNT HH 2
HHE-7112 KIT - HARDWARE - SINGLE AUXILARY TANK HARBORHOIST 1
HHE-7117 KIT - HARDWARE - SINGLE AUXILARY TANK FITTINGS 1
HH-3350 AUXILARY TANK ASSY WITH FITTING - HARBORHOIST 36X120X24 FLAT TOP 1

7Rev. 07142020
Chart 4: PARTS LIST—12000
HH-12000 V-HULL V-FRAME
Part Description Expected Qty
TANK ASSEMBLY
HH-3000 TANK- HARBORHOIST GEN 1.5 8
HH-2650 KIT BOX, HARBORHOIST GEN 1 MOD TANK SET 4
HH-2601 TOP PLATE - HH GEN 1 MOD- ALUMINUM 8
HH-LPL-1024 GASKET - TOP HARBORHOIST 8
HH-LPL-1028 GASKET - UNDERNEATH - HARBORHOIST 16
HH-LPL-1027 GASKET - BOTTOM - HARBORHOIST 16
HH-LPL-1026 BEAM STRAP - ALUMINUM - HARBOR HOIST 16
HH-LPL-1040 CHANNEL - SUPPORT HH - ALUMINUM 16
HH-LPL-1025 STRAP PLATE - ALUMINUM HARBORHOIST 16
CROSS BEAMS
HH-4310 CROSS CHANNEL - 3IN SQ. 100IN. V CENTER 8
WALKWAYS
HH-1428 WALKWAY PANEL - HARBORHOIST G1.5 39
HH-2515 SUPPORT-WALKWAY HARBORHOIST 8
HH-LPL-1034 BEAM - 48IN SPAN - ALUM. HH. 6
HH-LPL-1033 TUBE - SPACER, 3X3 ALUMINUM 4
HH-2525 END CAP- HH WALKWAY WITH DECAL 4
HULL PADS
1035066 ASSY HYH HARBORHOIST ALUM BUNK LEFT 22FT 1
1035067 ASSY HYH HARBORHOIST ALUM BUNK RIGHT 22FT 1
1035195 HARDWARE KIT - HARBORHOIST HULL PADS (1 PER TANK SET) 4
CONTROLS
1035233 HarborHoist Triton 5 Valve Single Blower -110 volt 1
HH-2517 CONTROL STAND HARBORHOIST GEN 1.5 1
HHE-2655 KIT, HARDWARE, CONTROL HARDWARE HH 2018 1
3072517 HOSE - RUBBER 1-1/4 in. ID X 100 ft. - CUT 1
3072512 HOSE - RUBBER 1-1/4 in. ID X 30 ft. - CUT 1
HH-2685 KIT, HARDWARE HOSE CLAMPS AND TEES, 8800 1
AUXILLARY (AUX) TANKS
HHE-7122 I-BEAM - SINGLE AUX TANK MOUNT HH 2
1033229A KIT - HARDWARE - SINGLE AUXILARY TANK HARBORHOIST 1
HHE-7117 KIT - HARDWARE - SINGLE AUXILARY TANK FITTINGS 1
HH-3730 AUXILARY TANK ASSY - HARBORHOIST 36X96X36 1

8Rev. 07142020
Chart 4: PARTS LIST—12000 Shallow
HH-12000 V-HULL SHALLOW V-FRAME
Part Description Expected Qty
TANK ASSEMBLY
HH-3000 TANK- HARBORHOIST GEN 1.5 8
HH-2650 KIT BOX, HARBORHOIST GEN 1 MOD TANK SET 4
HH-2601 TOP PLATE - HH GEN 1 MOD- ALUMINUM 8
HH-LPL-1024 GASKET - TOP HARBORHOIST 8
HH-LPL-1028 GASKET - UNDERNEATH - HARBORHOIST 16
HH-LPL-1027 GASKET - BOTTOM - HARBORHOIST 16
HH-LPL-1026 BEAM STRAP - ALUMINUM - HARBOR HOIST 16
HH-LPL-1040 CHANNEL - SUPPORT HH - ALUMINUM 16
HH-LPL-1025 STRAP PLATE - ALUMINUM HARBORHOIST 16
CROSS BEAM
HH-4310 CROSS CHANNEL - 3IN SQ. 100IN. V CENTER 8
WALKWAY
HH-1428 WALKWAY PANEL - HARBORHOIST G1.5 39
HH-2515 SUPPORT-WALKWAY HARBORHOIST 8
HH-LPL-1034 BEAM - 48IN SPAN - ALUM. HH. 6
HH-LPL-1033 TUBE - SPACER, 3X3 ALUMINUM 4
HH-2525 END CAP- HH WALKWAY WITH DECAL 4
HULL PADS
1035066 ASSY HYH HARBORHOIST ALUM BUNK LEFT 22 FT 1
1035067 ASSY HYH HARBORHOIST ALUM BUNK RIGHT 22 FT 1
1035195 HARDWARE KIT - HARBORHOIST HULL PADS (1 PER TANK SET) 4
CONTROL
1035233 HarborHoist Triton 5 Valve Single Blower -110 volt 1
HH-2517 CONTROL STAND HARBORHOIST GEN 1.5 1
HHE-2655 KIT, HARDWARE, CONTROL HARDWARE HH 2018 1
3072517 HOSE - RUBBER 1-1/4 in. ID X 100 ft. - CUT 1
3072512 HOSE - RUBBER 1-1/4 in. ID X 30 ft. - CUT 1
HH-2685 KIT, HARDWARE HOSE CLAMPS AND TEES, 8800 1
AUXILLARY (AUX) TANKS
HHE-7122 I-BEAM - SINGLE AUX TANK MOUNT HH 2
1033229A KIT - HARDWARE - SINGLE AUXILARY TANK HARBORHOIST 1
HHE-7117 KIT - HARDWARE - SINGLE AUXILARY TANK FITTINGS 1
1034895 TANK - AUXILIARY WITH FITTING HARBORHOIST 48X120X24 FLAT TOP 1

9Rev. 07142020
Chart 4: PARTS LIST—12000 Wide
HH-12000 V-HULL V-FRAME WIDE
Part Description Expected Qty
TANK ASSEMBLY
HH-3000 TANK- HARBORHOIST GEN 1.5 8
HH-2650 KIT BOX, HARBORHOIST GEN 1 MOD TANK SET 4
HH-2601 TOP PLATE - HH GEN 1 MOD- ALUMINUM 8
HH-LPL-1024 GASKET - TOP HARBORHOIST 8
HH-LPL-1028 GASKET - UNDERNEATH - HARBORHOIST 16
HH-LPL-1027 GASKET - BOTTOM - HARBORHOIST 16
HH-LPL-1026 BEAM STRAP - ALUMINUM - HARBOR HOIST 16
HH-LPL-1040 CHANNEL - SUPPORT HH - ALUMINUM 16
HH-LPL-1025 STRAP PLATE - ALUMINUM HARBORHOIST 16
CROSS BEAM
FRM-06-0007 CROSS CHANNEL - 3IN SQ. V CENTER 126 IN LONG 8
WALKWAY
HH-1428 WALKWAY PANEL - HARBORHOIST G1.5 39
HH-2515 SUPPORT-WALKWAY HARBORHOIST 8
HH-LPL-1034 BEAM - 48IN SPAN - ALUM. HH. 6
HH-LPL-1033 TUBE - SPACER, 3X3 ALUMINUM 4
HH-2525 END CAP- HH WALKWAY WITH DECAL 4
HULL PADS
1035066 ASSY HYH HARBORHOIST ALUM BUNK LEFT 22 FT 1
1035067 ASSY HYH HARBORHOIST ALUM BUNK RIGHT 22 FT 1
1035195 HARDWARE KIT - HARBORHOIST HULL PADS (1 PER TANK SET) 4
CONTROL
1035233 HarborHoist Triton 5 Valve Single Blower -110 volt 1
HH-2517 CONTROL STAND HARBORHOIST GEN 1.5 1
HHE-2655 KIT, HARDWARE, CONTROL HARDWARE HH 2018 1
3072517 HOSE - RUBBER 1-1/4 in. ID X 100 ft. - CUT 1
3072512 HOSE - RUBBER 1-1/4 in. ID X 30 ft. - CUT 1
HH-2685 KIT, HARDWARE HOSE CLAMPS AND TEES, 8800 1
AUXILLARY (AUX) TANKS
HHE-7122 I-BEAM - SINGLE AUX TANK MOUNT HH 2
1033229A KIT - HARDWARE - SINGLE AUXILARY TANK HARBORHOIST 1
HHE-7117 KIT - HARDWARE - SINGLE AUXILARY TANK FITTINGS 1
HH-3730 AUXILARY TANK ASSY - HARBORHOIST 36X96X36 1

10 Rev. 07142020
Chart 4: PARTS LIST—15000
HH-15000 V-HULL V-FRAME
Part Description Expected Qty
TANKS ASSEMBLY
HH-3000 TANK- HARBORHOIST GEN 1.5 8
HH-2650 KIT BOX, HARBORHOIST GEN 1 MOD TANK SET 4
HH-2601 TOP PLATE - HH GEN 1 MOD- ALUMINUM 8
HH-LPL-1024 GASKET - TOP HARBORHOIST 8
HH-LPL-1028 GASKET - UNDERNEATH - HARBORHOIST 16
HH-LPL-1027 GASKET - BOTTOM - HARBORHOIST 16
HH-LPL-1026 BEAM STRAP - ALUMINUM - HARBOR HOIST 16
HH-LPL-1040 CHANNEL - SUPPORT HH - ALUMINUM 16
HH-LPL-1025 STRAP PLATE - ALUMINUM HARBORHOIST 16
CROSS BEAM
HH-4310 CROSS CHANNEL - 3IN SQ. 100IN. V CENTER 8
WALKWAY
HH-1428 WALKWAY PANEL - HARBORHOIST G1.5 39
HH-2515 SUPPORT-WALKWAY HARBORHOIST 8
HH-LPL-1034 BEAM - 48IN SPAN - ALUM. HH. 6
HH-LPL-1033 TUBE - SPACER, 3X3 ALUMINUM 4
HH-2525 END CAP- HH WALKWAY WITH DECAL 4
HULL PADS
1035066 ASSY HYH HARBORHOIST ALUM BUNK LEFT 22 FT 1
1035067 ASSY HYH HARBORHOIST ALUM BUNK RIGHT 22 FT 1
1035195 HARDWARE KIT - HARBORHOIST HULL PADS (1 PER TANK SET) 4
CONTROL
1035233 HarborHoist Triton 5 Valve Single Blower -110 volt 1
HH-2517 CONTROL STAND HARBORHOIST GEN 1.5 1
HHE-2655 KIT, HARDWARE, CONTROL HARDWARE HH 2018 1
3072517 HOSE - RUBBER 1-1/4 in. ID X 100 ft. - CUT 1
3072512 HOSE - RUBBER 1-1/4 in. ID X 30 ft. - CUT 1
HH-2685 KIT, HARDWARE HOSE CLAMPS AND TEES, 8800 1
AUXILLARY (AUX) TANKS
HHE-7123 I-BEAM - DUAL AUX TANK MOUNT HH 2
1033229A KIT - HARDWARE - SINGLE AUXILARY TANK HARBORHOIST 2
HHE-7116 KIT - HARDWARE - DOUBLE AUXILARY TANKS 1
HH-3730 AUXILARY TANK ASSY - HARBORHOIST 36X96X36 2

11 Rev. 07142020
Chart 4: PARTS LIST—15000 Shallow
HH-15000 V-HULL V-FRAME SHALLOW
Part Description Expected Qty
TANK ASSEMBLY
HH-3000 TANK- HARBORHOIST GEN 1.5 8
HH-2650 KIT BOX, HARBORHOIST GEN 1 MOD TANK SET 4
HH-2601 TOP PLATE - HH GEN 1 MOD- ALUMINUM 8
HH-LPL-1024 GASKET - TOP HARBORHOIST 8
HH-LPL-1028 GASKET - UNDERNEATH - HARBORHOIST 16
HH-LPL-1027 GASKET - BOTTOM - HARBORHOIST 16
HH-LPL-1026 BEAM STRAP - ALUMINUM - HARBOR HOIST 16
HH-LPL-1040 CHANNEL - SUPPORT HH - ALUMINUM 16
HH-LPL-1025 STRAP PLATE - ALUMINUM HARBORHOIST 16
CROSS BEAM
HH-4310 CROSS CHANNEL - 3IN SQ. 100IN. V CENTER 8
WALKWAY
HH-1428 WALKWAY PANEL - HARBORHOIST G1.5 39
HH-2515 SUPPORT-WALKWAY HARBORHOIST 8
HH-LPL-1034 BEAM - 48IN SPAN - ALUM. HH. 6
HH-LPL-1033 TUBE - SPACER, 3X3 ALUMINUM 4
HH-2525 END CAP- HH WALKWAY WITH DECAL 4
HULL PADS
1035066 ASSY HYH HARBORHOIST ALUM BUNK LEFT 22 FT 1
1035067 ASSY HYH HARBORHOIST ALUM BUNK RIGHT 22 FT 1
1035195 HARDWARE KIT - HARBORHOIST HULL PADS ( 1 PER TANK SET) 4
CONTROL
1035233 HarborHoist Triton 5 Valve Single Blower -110 volt 1
HH-2517 CONTROL STAND HARBORHOIST GEN 1.5 1
HHE-2655 KIT, HARDWARE, CONTROL HARDWARE HH 2018 1
3072517 HOSE - RUBBER 1-1/4 in. ID X 100 ft. - CUT 1
3072512 HOSE - RUBBER 1-1/4 in. ID X 30 ft. - CUT 1
HH-2685 KIT, HARDWARE HOSE CLAMPS AND TEES, 8800 1
AUXILLARY (AUX) TANKS
HHE-7123 I-BEAM - DUAL AUX TANK MOUNT HH 2
1033229A KIT - HARDWARE - SINGLE AUXILARY TANK HARBORHOIST 2
HHE-7116 KIT - HARDWARE - DOUBLE AUXILARY TANKS 1
1034895 TANK - AUXILIARY WITH FITTING HARBORHOIST 48X120X24 FLAT TOP 2

12 Rev. 07142020
Chart 4: PARTS LIST—15000 Wide
HH-15000 V-HULL V-FRAME WIDE
Part Description Expected Quantity
TANK ASSEMBLY
HH-3000 TANK- HARBORHOIST GEN 1.5 8
HH-2650 KIT BOX, HARBORHOIST GEN 1 MOD TANK SET 4
HH-2601 TOP PLATE - HH GEN 1 MOD- ALUMINUM 8
HH-LPL-1024 GASKET - TOP HARBORHOIST 8
HH-LPL-1028 GASKET - UNDERNEATH - HARBORHOIST 16
HH-LPL-1027 GASKET - BOTTOM - HARBORHOIST 16
HH-LPL-1026 BEAM STRAP - ALUMINUM - HARBOR HOIST 16
HH-LPL-1040 CHANNEL - SUPPORT HH - ALUMINUM 16
HH-LPL-1025 STRAP PLATE - ALUMINUM HARBORHOIST 16
CROSS BEAM
FRM-06-0007 CROSS CHANNEL - 3IN SQ. V CENTER 126 IN LONG 8
WALKWAY
HH-1428 WALKWAY PANEL - HARBORHOIST G1.5 39
HH-2515 SUPPORT-WALKWAY HARBORHOIST 8
HH-LPL-1034 BEAM - 48IN SPAN - ALUM. HH. 6
HH-LPL-1033 TUBE - SPACER, 3X3 ALUMINUM 4
HH-2525 END CAP- HH WALKWAY WITH DECAL 4
HULL PADS
1035066 ASSY HYH HARBORHOIST ALUM BUNK LEFT 22 FT 1
1035067 ASSY HYH HARBORHOIST ALUM BUNK RIGHT 22 FT 1
1035195 HARDWARE KIT - HARBORHOIST HULL PADS (1 PER TANK SET) 4
CONTROL
1035233 HarborHoist Triton 5 Valve Single Blower -110 volt 1
HH-2517 CONTROL STAND HARBORHOIST GEN 1.5 1
HHE-2655 KIT, HARDWARE, CONTROL HARDWARE HH 2018 1
3072517 HOSE - RUBBER 1-1/4 in. ID X 100 ft. - CUT 1
3072512 HOSE - RUBBER 1-1/4 in. ID X 30 ft. - CUT 1
HH-2685 KIT, HARDWARE HOSE CLAMPS AND TEES, 8800 1
AUXILIARY (AUX) TANKS
HHE-7123 I-BEAM - DUAL AUX TANK MOUNT HH 2
1033229A KIT - HARDWARE - SINGLE AUXILARY TANK HARBORHOIST 2
HHE-7116 KIT - HARDWARE - DOUBLE AUXILARY TANKS 1
HH-3730 AUXILARY TANK ASSY - HARBORHOIST 36X96X36 2

13 Rev. 07142020
Chart 4: PARTS LIST—18000
HH-18000 V-HULL V-FRAME
Part Description Expected Qty
TANK ASSEMBLY
HH-3000 TANK- HARBORHOIST GEN 1.5 8
HH-2650 KIT BOX, HARBORHOIST GEN 1 MOD TANK SET 4
HH-2601 TOP PLATE - HH GEN 1 MOD- ALUMINUM 8
HH-LPL-1024 GASKET - TOP HARBORHOIST 8
HH-LPL-1028 GASKET - UNDERNEATH - HARBORHOIST 16
HH-LPL-1027 GASKET - BOTTOM - HARBORHOIST 16
HH-LPL-1026 BEAM STRAP - ALUMINUM - HARBOR HOIST 16
HH-LPL-1040 CHANNEL - SUPPORT HH - ALUMINUM 16
HH-LPL-1025 STRAP PLATE - ALUMINUM HARBORHOIST 16
CROSS BEAM
HH-4310 CROSS CHANNEL - 3IN SQ. 100IN. V CENTER 8
WALKWAY
HH-1428 WALKWAY PANEL - HARBORHOIST G1.5 39
HH-2515 SUPPORT-WALKWAY HARBORHOIST 8
HH-LPL-1034 BEAM - 48IN SPAN - ALUM. HH. 6
HH-LPL-1033 TUBE - SPACER, 3X3 ALUMINUM 4
HH-2525 END CAP- HH WALKWAY WITH DECAL 4
HULL PADS
1035066 ASSY HYH HARBORHOIST ALUM BUNK LEFT 22 FT 1
1035067 ASSY HYH HARBORHOIST ALUM BUNK RIGHT 22 FT 1
1035195 HARDWARE KIT - HARBORHOIST HULL PADS (1 PER TANKS SET) 4
CONTROL
1035233 HarborHoist Triton 5 Valve Single Blower -110 volt 1
HH-2517 CONTROL STAND HARBORHOIST GEN 1.5 1
HHE-2655 KIT, HARDWARE, CONTROL HARDWARE HH 2018 1
3072517 HOSE - RUBBER 1-1/4 in. ID X 100 ft. - CUT 1
HH-2685 KIT, HARDWARE HOSE CLAMPS AND TEES, 8800 1
AUXILIARY (AUX) TANKS
HHE-7123 I-BEAM - DUAL AUX TANK MOUNT HH 2
1033229A KIT - HARDWARE - SINGLE AUXILARY TANK HARBORHOIST 2
HHE-7116 KIT - HARDWARE - DOUBLE AUXILARY TANKS 1
HH-5130 AUXILARY TANK ASSY - HARBORHOIST 48X96X36 2

14 Rev. 07142020
Chart 4: PARTS LIST—18000 Wide
HH-18000 V-HULL V-FRAME WIDE
Part Description Expected Qty
TANK ASSEMBLY
HH-3000 TANK- HARBORHOIST GEN 1.5 8
HH-2650 KIT BOX, HARBORHOIST GEN 1 MOD TANK SET 4
HH-2601 TOP PLATE - HH GEN 1 MOD- ALUMINUM 8
HH-LPL-1024 GASKET - TOP HARBORHOIST 8
HH-LPL-1028 GASKET - UNDERNEATH - HARBORHOIST 16
HH-LPL-1027 GASKET - BOTTOM - HARBORHOIST 16
HH-LPL-1026 BEAM STRAP - ALUMINUM - HARBOR HOIST 16
HH-LPL-1040 CHANNEL - SUPPORT HH - ALUMINUM 16
HH-LPL-1025 STRAP PLATE - ALUMINUM HARBORHOIST 16
CROSS BEAM
FRM-06-0007 CROSS CHANNEL - 3IN SQ. V CENTER 126 IN LONG 8
WALKWAY
HH-1428 WALKWAY PANEL - HARBORHOIST G1.5 39
HH-2515 SUPPORT-WALKWAY HARBORHOIST 8
HH-LPL-1034 BEAM - 48IN SPAN - ALUM. HH. 6
HH-LPL-1033 TUBE - SPACER, 3X3 ALUMINUM 4
HH-2525 END CAP- HH WALKWAY WITH DECAL 4
HULL PADS
1035066 ASSY HYH HARBORHOIST ALIM BUNK LEFT 22 FT 1
1035067 ASSY HYH HARBORHOIST ALIM BUNK RIGHT 22 FT 1
1035195 HARDWARE KIT - HARBORHOIST HULL PADS (1 PER TANK SET) 4
CONTROL
1035233 HarborHoist Triton 5 Valve Single Blower -110 volt 1
HH-2517 CONTROL STAND HARBORHOIST GEN 1.5 1
HHE-2655 KIT, HARDWARE, CONTROL HARDWARE HH 2018 1
3072517 HOSE - RUBBER 1-1/4 in. ID X 100 ft. - CUT 1
HH-2685 KIT, HARDWARE HOSE CLAMPS AND TEES, 8800 1
AUXILARY (AUX) TANKS
HHE-7123 I-BEAM - DUAL AUX TANK MOUNT HH 2
1033229A KIT - HARDWARE - SINGLE AUXILARY TANK HARBORHOIST 2
HHE-7116 KIT - HARDWARE - DOUBLE AUXILARY TANKS 1
HH-5130 AUXILARY TANK ASSY - HARBORHOIST 48X96X36 2

15 Rev. 07142020
STEP 1: WALKWAY TOP PLATE ASSEMBLY
1. Align the mounng holes for the Top Plate and Top Gasket.
2. Run the Bolts and Liing Ring through the Top Plate and Top Gasket. Fasten with washers as illustrated below.
Bolt 1/4 x 20
Flat Washer 1/4” (x8)
Brass Hex Nut 1/2-13
Lock Washer 1/2” 18-8 SS
Liing Ring 1.5 x 4 SS
Nylock Nut 1/4-20 SS (x4)
Top Gasket
Top Plate
Flat Washer 1/4”
Part # Hardware Required
HH-LPL-1502 Nyloc Nut (1/4-20 SS)
HH-LPL-1501 Hex Bolt (1/4-20 x 1.5 SS)
2090216 Flat Washer (1/4” SS)
HH-1916 Lock Washer 1/2” 18-8 SS
HH-1926 Hex Nut 1/2-13 Brass
HH-2602 Liing Ring 1.5 x 4 SS
Part # Parts Required (Per Tank)
HH-2601 Top Plate
HH-LPL-1024 Top Gasket
Use Kit Box: #HH-2650

16 Rev. 07142020
STEP 2: ATTACH TOP PLATE ASSEMBLY TO STRAP PLATES
1. Align the Walkway Assembly with a Strap Plate.
2. Put U-Bolts through the Strap Plate and into the Walkway assembly, loosely fastening as illustrated.
3. Repeat the process for the second Strap Plate.
NOTE: Only hand ghten Brass Hex Nuts on top of the U-Bolts. They will be removed later to assemble the walkway.
Lock Washer (3/8”) (x8) Brass Hex Nut (3/8-16) (x8) U-Bolt (3/8-16 x 3 x 5) (x4)
Strap Plate (x2) Walkway Assembly
Part # Parts Required (Per Tank)
NA Walkway Assembly
HH-LPL-1025 Strap Plate
Part # Hardware Required
HH-LPL-1503 U-Bolt 3/8-16 x 3 x 5
2090242 Flat Washer 3/8”
HH-LPL-1505 Lock Washer 3/8”
HH-2603 Brass Nut 3/8-16
Assembly aid: Aach zip es to the bases of the U-Bolts to keep them in place during installaon. Zip es
are not provided in the kit.
Use Kit Box: #HH-2650

17 Rev. 07142020
STEP 3: ATTACH TANK FRAME BRACKETS TO STRAP PLATES
U-Bolt
Support Channel
Boom Gasket
Nylon Bushing (2)
Flathead Bolt
Aach Zip Ties
Part # Parts Required (Per Tank)
HH-LPL-1040 Channel Support
HH-LPL-1027 Boom Gasket
HH-LPL-1025 Strap Plate
Part # Hardware Required
HH-LPL-1504 U-Bolt (3/8-16 x 3 x 6)
HH-LPL-1006 Flat Head Bolt (5” SS)
HH-LPL-1031 Nylon HH Tank Bushing
H-1926 Hex Nut (1/2-13 Brass)
HH-1916 Lock Washer
1. Align the mounng holes for the Channel Support, Strap Plate, and Boom Gasket.
2. Slide the U-Bolts through the boom of the Channel Support.
Assembly Aid: Aach Zip Ties to the bases of the U-Bolts to keep them in place during installaon. Zip Ties are
not provided in the kit.
3. Insert the 5” Flat Head Bolt through the Channel Support and the Boom Gasket.
IMPORTANT: Tighten the Nuts against the Nylon Bushing so the Bolts cannot rotate before assembling into the
tank. This will make it easier to assemble the Boom Gasket in Step 4.
Use Kit Box: #HH-2650
Lock washer
Hex Nut
Lock washer
Hex Nut
Strap

18 Rev. 07142020
STEP 4: ATTACH STRAP TANK ASSEMBLY TO TANK
Tank shown on its back.
1. Roll the tank onto its back for unobstructed access to the top and boom of the tank, as illustrated below.
2. Place the completed Strap Plate Assembly into the recesses along the front and top of the tank.
The next procedure must be followed in order to prevent damage to the tank. DO NOT force the
assembly together as this could cause the nylon bushing to damage the tank.
3. Slide Strap Tank’s 1/2 x 13 x 8” Hex Bolts with nylon bushing assembly through the tank.
4. Assemble the Underneath Tank Gasket onto the 1/2” x 13 x 8” bolts and hand ght assemble with the at wash-
ers and Brass Nyloc Nuts.
5. Evenly ghten the Brass Nyloc Nuts so that the assembly pulls together without binding.
6. When you have completely pulled the assembly together Torque the Top-Side Brass Nut to specicaon.
Part # Parts Required (Per Tank)
HH3000 Tank
HH-LPL-1028 Gasket - Underneath Tank
Part # Hardware Required
HH-LPL-1508 Flat Washer (1/2 x2 OD SS)
HH-2100 Brass Nyloc Nut (1/2-13)
Strap Tank Assembly
Gasket Under-
neath Tank
(Boom-
Side) 1/2”
Hex Nut +
Flat Washer
Nylon Bushing
Use Kit Box: #HH-2650

19 Rev. 07142020
STEP 5: STUB TUBE INSTALLATION
1. Reposion the tank in the upright posion.
2. Apply thread sealant to the Stub Tube Recommend Sealants: #2 Permatex, 3M 4200, or Permatex with
PTFE. Sealant must have PTFE. See sealant manufacturer applicaon instrucons.
3. Screw the Stub Tube into the tank ng.
4. Apply Thread Sealant to the elbow and screw into Stub Tube ng. You may need to hold the Stub Tube
ng with a pipe wrench to avoid turning it while screwing in the elbow. As the threads ghten, pay
aenon to the direcon that the elbow /hose is poinng.
• Oen, the li’s hull pad dead rise is shallower than that of the vessel. To increase the dead rise
capability of the li, the Stub Tube may need to be trimmed. See Chart 6 for trimming the Stub
Tube and Chart 7 for spacing hull pads. In combinaon, these will give you the dra of the li
needed for your vessel.
• Be careful not to overshoot the desired alignment since backing o the Stub Tube can cause a
leak path around the ng. The Stub Tube can be hand ghtened such that minimal threads on
the elbow are visible.
REPEAT STEPS 1-5 FOR EACH TANK BEFORE PROCEEDING TO STEP 6.
Part # Parts Required (Per Tank)
HHE-2650 Stub Tube Assembly (Kit Box)
Part # Hardware Required
HHE-2650 Hose Clamp #24 (Kit Box)
Not supplied Thread Sealant
Stub Tube Assembly in Tank
Stub Tube Stub Tube Elbow
Use Kit Box: #HH-2650

20 Rev. 07142020
STEP 5: STUB TUBE INSTALLATION (Connued)
Tanks sets are numbered from front to rear. Set 1 is the farthest forward.
Chart 6: STUB TUBE MAXIMUM TRIM PER TANK SET
Forward Front to Rear (in.) A
Model Lis SET 1 SET 2 SET 3 SET 4 SET 5
8800 Short 01.5" 3"
12000 01" 2" 3"
12000 Shallow 01" 2" 3"
12000 Wide 01" 2" 3"
15000 01" 2" 3"
15000 Shallow 01" 2" 3"
15000 Wide 01" 2" 3"
18000 01" 2" 3"
18000 Long 01" 2" 3"
18000 Wide 00.75" 1.5" 2.25" 3"