HYDROSCAND AutoCut 5-32CTS User manual

USER MANUAL Edition II
2016-12-28
Serial number:
AutoCut 5-32CTS

CONTENTS
1. INTRODUCTION........................................ 4
2. GENERAL PRECAUTIONS ............................ 4
3. EQUIPMENT........................................ 5 - 6
3.1 WARRANTY....................................... 4
3.2 IMPORTANT ...................................... 5
4. MACHINE................................................ 6
4.1 IDENTIFICATION ............................... 6
4.2 DESCRIPTION ................................... 6
5. STARTING - UP ..................................7 - 40
5.1 CONNECT THE MACHINE ...................... 7
5.2 OPERATOR POSITION.......................... 8
5.3 INITIAL START UP ........................ 8 - 9
5.4 TOOL CHANGE ..................................10
5.4.1 CONTROL PANEL.............................11
5.5 MAIN, STANDARD SCREEN................12
5.5.1 AUTO SEQUENCE MENU....................13
5.5.2 AUTO - RECIPE ..............................14
5.5.3 DRIVE/ADJUST PARAMETAR .............15
5.5.4 SETTINGS.....................................16
5.5.5 LENGTH CONTROL...........................17
5.5.6 MACHINE PARAMETAR.....................18
5.5.7 MANUAL HANDLE OUTPUT ...............19
5.5.8 TIMERS MENU ...............................20
5.5.9 PRINT OUT MENU...........................21
5.5.10 ALARMLIST .................................22
5.6 MAIN BIG SCREEN.......................... 23
5.6.1 ARTICLE.......................................24
5.6.2 ARTICLE RECIPE ............................25
5.6.3 ARTICLE RECIPE ............................26
5.6.4 ORDER .........................................27
5.6.5 ORDER .........................................28
5.6.6 PRINT OUT ...................................29
5.6.7 ORDER, RUN VIEW..........................30
5.6.8 BATCH .........................................31
5.7 SETTINGS .......................................32
5.7.1 MISCELLANEOUS ............................33
5.7.2 MACHINE PARAMETER .....................34
5.7.3 I/O CONTROL INPUT - OUTPUT..........35
5.7.4 TIMMERS / COUNTERS.....................35
5.7.5 HAND OPERATED OUTPUT ................36
5.7.6 LENGTH STATISTICS........................37
5.7.7 LENGTH CONTROL...........................38
5.7.8 ALARMLIST...................................39
5.8 HANDLING OF THE MACHINE ..............40
5.9 ANDON LIGHT FUNCTION ...................40
Page 2
AUTOCUT 5-32CTS USER MANUAL EDITION II 2015-01-16
Page 3
AUTOCUT 5-32CTS USER MANUAL EDITION II 2015-01-16

Page 2
AUTOCUT 5-32CTS USER MANUAL EDITION II 2015-01-16
CONTENTS
6. MAINTENANCE................................. 41 - 43
6.1 REPLACEMENT OF CUTTING BLADE .......41
6.2 AFTER EACH WORKING SHIFT .............42
6.3 REGULAR MAINTENANCE....................42
6.4 RESET MOTOR CIRCUIT BREAKER .........42
6.5 CHANGE OF DRIVE BELTS ...................42
6.6 ADJUST HOSE PREBEND ANGLE ...........43
7. TROUBLE SHOOTING ................................44
8. TECHNICAL DATA.....................................45
9. TECHNICAL / ELECTRICAL DRAW ......... 46 - 64
Page 3
AUTOCUT 5-32CTS USER MANUAL EDITION II 2015-01-16

Page 4
AUTOCUT 5-32CTS USER MANUAL EDITION II 2015-01-16
1. Introduction
The purpose of this manual is to provide the necessary information for competent,
safe use of the hose cutting machine.
This information is the result of continuous, systematic data processing and technical
tests recorded and validated by the manufacturer, in accordance with the internal
procedures to ensure the safety of information: 2006/42/EC.
The information below is intended EXCLUSIVELY for specialized users, capable of interac-
ting with the product with the utmost safety people, the machine and the environment,
interpreting basic diagnostics of problems and malfunctions and performing simple checks
and maintainance, in full compliance with the instructions given from the pages that fol-
lows and with current health and safety regulations.
The manual does not examine in depth the topics of disassembly and extraordinary main-
tainance, as these operations must always be carried out by our authorized Technical Ser-
vice.
To handle the machine properly, it is necessary to keep the manual in good condition for
the future. Contact the nearest authorized technical service if you need a new manual or
more complete information.
Before each intervention to the machine or its packaging, read the instructions in the fol-
lowing manual very carefully.
Every operator using the machine, MUST read the following instructions before
operating.
Hydroscand Machine AB declines any responsability for damage to persons, things or to the
machine itself, arising fromits incorrect use, neglience and supercial interpretations of
safety concepts in this manual.
This instruction manual should serve for the duration of the cutting machine´s operating
life and be available for at least 10 (ten) years. We recommend to keep it in a known and
accessible place (possible together with other documents related to the machine).
2. General precautions
Always make sure in advance that the minimum safety, placement and operating standards
are respected, taking note of the environmental conditions, temperature, humidity, ligh-
ting, vibrations, suspended dust and the appropriateness of the area to be occupied.
For unloading from pallet or moving of an unpacked machine, the lifting device on the top
must be used. Any other lifting device may cause damage to people, property or the
machine itself.
The cutting machine is constructed to operate indoors (workshops, industries etc.) where
there is no risk of explosion or re.
Do not combine the machine with other equippment unless you have an approval from the
manufacturer. If other equippment are installed on the machine, or if the machine is com-
bined with other equippment it’s necessary to make a risk analysis and a CE approval for the
whole foundation.

Page 5
AUTOCUT 5-32CTS USER MANUAL EDITION II 2015-01-16
Before cutting the rst hose, make sure that the cutting blade rotates in the correct
direction (see rotation arrow) and that the hose is placed steady towards the adjustable
cutting support. Also make sure that the hose is held steady so that there will be no risk
for injuries or damages. Do not put your hands in the cutting blade working area.
Do not cut hoses shorter than 100 mm! if so the load on the cutting blade will be
wrong.
Do not remove the information plates on the cutting machine. Make sure they are readable
and that you are sure about their meaning. Should they deteriorate, replace them immedia-
tely by contacting an authorized Technical Service.
The use of spares that do not respond to the specications listed below, changes or
manipulations - however slight- shall exempt Hydroscand Machine AB from any
responsability regarding the proper use and functioning of the cutting machine and safety
of peole and/or property.
It is strictly forbidden to tamper with safety equipment and/or devices.
NOTE !
Any maintenance operations, except for those specically described on the pages of this
manual, must be carried out by skilled personnel co-ordinated by authorized Technical
Service. Service access keys must not be kept together with the machine, these are exclu-
sively for authorized service personell. Dispose of processing waste in compliance with
current regulations.
3. Equipment
Our stationary AutoCut 5-32CTS hose cutting machine is supplied ready to use (except for the
plug), packed on a pallet.
NOTE !
The packing material must be disposed according to current environmental protecting regulation.
The machine is supplied initially with:
• Cutting blade HSM 520x4x38 mm Toothed
• 14 pcs sets of cutting tools (for 1/4”-1 1/4” hose)
• 2 sets of service access keys (only for authorized service personell)
• Wiring diagram and pneumatic scheme.
• Instruction manual
• Certicate regarding agreement according to EC Directive
3.1 Warranty
The cutting machine is guaranteed for one (1) year following the date of purchase; the war-
ranty is valid only if all of the instructions listed on the warranty certicate and in this
manual are fully complied with.
NOTE !
When unpacking the cutting machine, make sure that the machine is in perfect condition
and that the package contains the parts described.
Hydroscand Machine AB does not respond for errors or missing parts not reported to
Hydroscand Machine AB following eight (8) days after shipment.

Page 6
AUTOCUT 5-32CTS USER MANUAL EDITION II 2015-01-16
3.2 Important
The hose cutting machine is designed, manufactured and protected for cutting 1- and 2
layers hydraulic hose with dimension from 3/16” up to 1 1/4” and for cutting 4-layers
hydraulic hose with dimension from 3/16” up to 1”. Any other use is excluded by
Hydroscand Machine AB, who shall be exempt from any liability for damage to people,
property or the machine itself, caused by improper use.
Do not cut solid steel, wood or other unknown material, that can cause damage to
people, property or the machine itself.
4. Machine
4.1 Identication
The information for identifying the machine is found on the plates, located outside of
the cutting machine. This essentially includes:
• Manufacturer
• Serial number
• Year of manufacture
• Voltage (V)
• Hertz (Hz)
• Amperes (A)
• Weight
NOTE !
It is strictly forbidden to remove or damage the plate. Should this happend, always
contact an authorized Techical Service only.
For any information and/or technical explanations regarding the cutting machine, always
indicate:
• Model
• Serial number
• Edition and preparation date of the instruction manual.
4.2 Description
The AutoCut 5-32CTS hose cutting machine has a PLC-system which controls electric and
pneumatic functions. The software has an automatic cut length check, which controls that
hose length is within it’s tolerance. Driving parameters and other data is set in a colour
touch screen operator panel. The unit is also equipped with a smoke evacuator connection
and, as standard, with a toothed cutting blade assembled on the machine.
Hosefeeding is performed by servomotor driven belt.
The machine is equipped with an air pressure sensor, which means that if the air pressure
becomes too low, all functions will be shut down and the machine will stop. It cannot be
restarted until the air pressure has reached min. 6 bar.
The pneumatic system has a softstart function at startup or reset.
The hose cutting machine must onle be used for hydraulic hoses compatible with the
specications. Follow the environmental conditions and limitations recommended by
Hydroscand Machine AB and current health and safety regulations.
NOTE !
The descriptions includes the use for which the machine has been designed, built and pro-
tected. Any other use or failure to comply with the technical parameters listed below, may
constitute a hazard to people and/or property.

Page 7
AUTOCUT 5-32CTS USER MANUAL EDITION II 2015-01-16
5. Starting - up
5.1 Connect the machine
• Place the machine on a steady and at foundation.
• Check that the cutting blade is tightened and can rotate freely.
• Connect the machine, main power inlet is placed inside the machine and the other
connections are under the electric box (picture A), see also the electrical drawing.
• Connect the air inlet supply to min. 6 bar with a min. 3/8” hose size.
• Check the rotation direction of the cutting blade, rotation must be according to sticker
on cut blade hatch. Perform this check visually by opening the top hatch and check before
the motor has stopped rotate.
NOTE !
Before plugging in the machine, make sure that the line voltage corresponds to the voltage
indicated on the machine. Verify the wire connections with the electrical drawing enclosed
with the machine.
HYDROSCAND MACHINE AB
Kungsvägen 22 Phone: +46 (0)225 - 573 30
S-783 35 Säter Fax: +46 (0)225 - 501 08
Sweden Web: www.hydroscand-machine.se
Edition 7-00
MANUAL -E
Page 7
6. Start up
6.1 Preliminary steps
Important!
It is essential to determine size measurements and placement in advance in order
to ensure safe placement, running and emergency actions within the surrounding
environment. These conditions should be respected beginning with the
preliminary stages, before cutting begins.
• Place the machine on a steady and flat foundation.
• Connect the machine, main power inlet is placed inside the machine and the other
connections are under the electric box (picture A), see also the electrical drawing.
• Connect the air inlet supply to min. 6 bar with a min. 3/8" hose size.
• Check that the cutting blade is tightened and can rotate freely.
• Check the rotation direction of the cutting blade.
NOTE !
Before plugging in the machine, make sure that the line voltage corresponds to
the voltage indicated on the machine.
Verify the wire connections with the electrical drawing enclosed with the machine.
A
X1 X2 X3 X4 X5
X1 Conveyor start/stop
X2 External Start/stop (option)
X3 HoseReel EOS power
X4 HoseReel EOS Start/stop
X5 Controlpanel

Page 8
AUTOCUT 5-32CTS USER MANUAL EDITION II 2015-01-16
5.2 Operator position
The placement of the machine in relation to the operator´s position must make it possible
to observe the result of the operation and maintain safety conditions. During this stage,
make sure that the start/stop button and the emergency switch not are blocked and that
there is sufcient visibility and lighting on the machine, the surrounding area and base.
5.3 Initial start up
1. Turn on the main switch.
2. Release the emergency stop button by turning it clockwise.
3. Press the emergency reset button.
4. Press the system on button.
5. Press the blue safety gate reset button on the controlpanel after the hatch is closed.
6. Turn on the 3-way switch.
On the touch screen:
7. Press the ”Settings” button.
8. Press the ”Hand operated Output” button, choose ”Cutmotor start” button
then press the ”Stop” button.
9. Check the rotation* of the cutting blade.
It must follow the direction arrow label placed at the cutting blade hatch.
Important!
*The top of the cutting blade must rotate towards the back part of the cutting machine.
Clockwise rotation, seen from the motor shaft side.
1
34
2
6 5
7

Page 9
AUTOCUT 5-32CTS USER MANUAL EDITION II 2015-01-16
HoseReel EOS
HoseReel 1
1. Remove the 5 pins from the HoseReel and load the hose, insert the pins again to
center the coil.
2. Push lever to position “Open” and then open the safety cover.
3. Pull the hose thru all hose guides and into the cutting machine.
4. Close the safety hatch and push the lever to “closed” position.
5. Turn the 3-way switch for the HoseReel to “Forward” on the AutoCut
Caution! The arm on the HoseReel feeding unit will now start automatically when the
hose “loop” decreases and stop again when the arm is in lowest position.
3
1
2
4

Page 10
AUTOCUT 5-32CTS USER MANUAL EDITION II 2015-01-16
Page 11
AUTOCUT 5-32CTS USER MANUAL EDITION II 2015-01-16
5.4 Tool change
HYDROSCAND MACHINE AB
Kungsvägen 22 Phone: +46 (0)225 - 573 30
S-783 35 Säter Fax: +46 (0)225 - 501 08
Sweden Web: www.hydroscand-machine.se
Edition 7-00
MANUAL -E
Page 9
First tool (inlet) is assembled between
the two aluminium blocks.
Choose the tool with 3-4mm bigger
hole than the hose OD size to avoid
problems during feeding of the hose.
The cutting side tools is assembled in
the same way as the first one.
Remember to have the same size on all
3 sets of the tooling.
This is the tools when correct
assembled and ready to use.
The tools has a size marking on the top.
It's not possible to assemble the tools
incorrectly.
The hose end shall always extend at
least 10mm outside the last tool before
start.
6.4 Hose guide toolings
First tool (inlet) is assembled between
the two aluminium blocks.
Choose the tool with 3-4mm bigger
hole than the hose OD size to avoid
problems during feeding of the hose.
The cutting side tools is assembled in
the same way as the rst one.
Remember to have the same size on all
3 sets of the tooling.
This is the tools when correct
assembled and ready to use.
The tools has a sizemarking on the top.
It’s not possible to assemble the tools
incorrectly.
The hose end shall always extend at
least 10mm outside the last tool before
start.

Page 10
AUTOCUT 5-32CTS USER MANUAL EDITION II 2015-01-16
Page 11
AUTOCUT 5-32CTS USER MANUAL EDITION II 2015-01-16
5.4.1 Control panel
1. Main power switch
2. Bypass safety gate switch
2-way switch with key lock. Access exclusively for service personell.
3. Emergency stop reset pushbutton
Reset at start-up and when the emergency stop has been activated.
4. System on button
5. System off button
6. Touch screen
7. Emergency stop
8. Alarm Indicator lamp
9. SPC-test indicator lamp
10. 3-way reset switch
Use this switch to open the belt unit and reset the sequence. Set to ”0” disables the
”Auto” function and should be used whenever machine is left without attention.
11. Safety hatch reset pushbutton
Reset at start up and when the hatch has been opened.
12. HoseReel EOS feeding direction switch
On/Off and rotation of optional feeding system.
First tool (inlet) is assembled between
the two aluminium blocks.
Choose the tool with 3-4mm bigger
hole than the hose OD size to avoid
problems during feeding of the hose.
The cutting side tools is assembled in
the same way as the rst one.
Remember to have the same size on all
3 sets of the tooling.
This is the tools when correct
assembled and ready to use.
The tools has a sizemarking on the top.
It’s not possible to assemble the tools
incorrectly.
The hose end shall always extend at
least 10mm outside the last tool before
start.
1
32 45
7
10 11 12
8 9
6

Page 12
AUTOCUT 5-32CTS USER MANUAL EDITION II 2015-01-16
5.5 Main, standard screen
1. Auto: Press to get ”Auto sequence” menu, the normal run menu.
2. Recipe: Press to get ”Auto”menu, the normal run menu.
3. Drive param: Press to get ”Adjust parameter” menu for changing drive parameters.
4. Settings: Press to get ”Test” menu for setup and monitoring of machine
functions.
5. Alarmlist: Press ”Alarmlist” menu button for alarm messages at error.
6. Time and date: Set time and date with the pop-up window simply by
touching this eld.
7. Alarm indicator: A ashing bell-symbol indicates if there is an alarm.
AUTOCUT 5-32
08-12-14 8:54:10
AUTO
AUTO AUTO RECIPE AUTO DRIVE PARAM AUTO SETTINGS
AUTO
ALARMLIST
1
5
7
6
2 3 4

Page 13
AUTOCUT 5-32CTS USER MANUAL EDITION II 2015-01-16
5.5.1 Auto sequence menu
This menu is the normal run menu from which the Autocut sequence can be controlled and
the status be monitored.
1. Actual article: Name of the loaded and saved recipe, if any parameter is changed
from the original recipe the text ”Recipe not saved” will appear.
2. Requested length: Requested length of each hose in mm.
3. Requested: Requested hose quantity in actual batch.
4. Status indication of Auto sequence: Off when stopped or paused, On when
sequence is running.
5. Cycle start: Press to start the autocut sequence.
6. Cycle stop: Press to stop the running autocut sequence.
7. Pause/Adjust: Press to temporarily pause the sequence. The machine will nnish the
already started section of the sequence, e.g. feeding or cutting.
The Adjust Parameter menu will appear on the screen.
8. Home: Press to return to Main menu.
9. Actual: Number of cuts performed in the batch. To reset counter goto the Adjust para-
meter menu with Pause/Adjust button.
AUTO SEQUENCE
0
00000 mm
0000 Pcs 0000 Pcs
Quantity
OFF
AUTO
CYCLE
START AUTO
CYCLE
STOP AUTO
PAUSE/
ADJUST AUTO
HOME
Actual Article
Request Length
Requested Actual
3
4
1
2
9
6
57 8

Page 14
AUTOCUT 5-32CTS USER MANUAL EDITION II 2015-01-16
5.5.2 Auto - Recipe menu
This menu work as a Initial setup window with possibility to save all parameters to the
data base memory. The same parameters can also be set from the ”Adjust parameter” menu
if you only need to make some temporarily setups for the actual batch which you don’t
need to save to memory.
1. Actual No: Name of the loaded and saved recipe, if any parameter is changed
from the original recipe the text ”Recipe not saved” will appear..
2. Length: Requested length of each hose in mm.
3. Feedspeed: Feeding speed for the belt, maximum value is 50m/min.
4. SPC-Test: The machine will pause cutting and the operator can perform a statistic
process control when this chosen amount is fullled. When the sequence has paused a
ashing text ”SPC-test” will appear in the ”Auto sequence” menu and the operater, can
when the test is done, continue the cutting with the ”Cycle start” button.
5. Quantity Req: Requested hose quantity for the batch.
6. Corr+/-: Correction of the hose length in mm. If achived hose length doesn’t match
requested length a correction, plus or minus, can be set.
7. Belt pressure: High or low pressure on the belt unit. Always choose low pressure unless
trouble with hose feeding has occured.
8. Cut position: High or Low for the cutting blade upper end position.
”Low” can be used for small and medium OD hoses.
”High” is used for big OD hoses.
Wrong setting gives not fully cut through or unnecessary friction to the sides of the
blade and less cuts per hour.
Preset position can be adjusted by moving sensor(s) on the cut cylinder.
AUTO - RECIPE
0
00000 mm
00 m/min
0000 Pcs
0000 Pcs
00 mm
Low
Low
Low
No
AUTO
DEL AUTO OPEN AUTO SAVE AUTO
AUTO
ARTICLE No.
Length
Feed speed
SPC-Test
Quantity Req.
Corr +/-
Belt pressure
Cut position
Cut speed
Print out
3
4
1
2
98
6
7
10
12 13 14
11
5

Page 15
AUTOCUT 5-32CTS USER MANUAL EDITION II 2015-01-16
9. Cut speed: Low, Medium or High travel speed of the cutting blade.
Low: Hose dimension 3/4” to 1 1/4” and all multispiral hose.
Medium: Hose dimension 3/8” to 5/8”
High: Hose dimension 3/16” to 5/16”
Preset values can be adjusted on adjusting screws for each pneumatic valve.
10. Print out: (Option) Engage automatic printout function of workreport.
11. Del: Delete saved recipe(s) from memory, choose one or all from scroll list.
12. Open: Open saved recipe from memory, choose from scroll list.
13. Save: Save changed recipe to memory, choose ”Replace existing” or ”Save as new”.
14. Auto: Close this menu and open ”Auto sequence” menu.
5.5.3 Drive/Adjust Parametar
This menu work as a initial setup/change window when you quickly want to run one batch
only and with it’s own settings. However, these changed settings can be saved by pressing
”Home” and then ”Recipe” and ”Save”.
1. Parameters can be set as in ”Article-Recipe” menu.
2. Reset quantity: Reset the actual quantity eld = new batch.
3. Open belt: Open belt unit and release the loaded hose.
4. Close belt: Close the belt unit which then is prepared for feeding the hose.
5. Auto: Close this menu and open up ”Auto sequence” menu. ”Auto sequence” menu is the
normal ”run” menu.
6. Home: Press to return to ”Main” menu.
ADJUST PARAMETER
wwwwwwwwwwwwwww
00000 mm
00 m/min
0000 Pcs
0000 Pcs
00 mm
Low
Low
Low
AUTO
RESET
QUANTITY
OPEN
BELT
OPEN
CLOSE HOME
AUTO
ARTICLE No.
Length
Feed speed
SPC-Test
Quantity Req.
Corr +/-
Belt pressure
Cut position
Cut speed
1
34 5 6
2

Page 16
AUTOCUT 5-32CTS USER MANUAL EDITION II 2015-01-16
5.5.4 Settings/Test menu
This menu is for setup and monitoring and calibration of basic machine functions, here are
also several possibilitys to manually test out the functions one at a time.
1. Counter length: Open ”Length control” menu for setting of the length tolerances
and monitoring of cut length during cutting.
2. Machine Parameter: Menu for calibration of cut length, password required.
3. Output: Open ”Manual handle output” menu for electric and pneumatic functions.
4. Timers: Open ”Timer” menu for machine functions.
5. Print out: Open ”Print out” menu.
6. Input: Open ”I/O control input” menu.
7. Home: Press to return to ”Main” menu.
TEST (MANUAL)
COUNTER
LENGTH TIMERS
PRINT
OUT
MACHINE
PARAMETER
INPUT
OUTPUT HOME
14
5
2
3
6 7

Page 17
AUTOCUT 5-32CTS USER MANUAL EDITION II 2015-01-16
5.5.5 LENGTH CONTROL
This menu is for monitoring and setting of length tolerances.
1. Requested length: Display for requested cut length.
2. Ext. Current Length: Display for actual output length.
3. Length tolerance +: Set the required plus tolerance with the pop-up window by
touching the display eld. Conrm value with Enter key: Too narrow tolerance will cause
Length error and stop in the batch.
4. Length tolerance -: Set the required minus tolerance with the pop-up window by
touching the display eld. Conrm value with Enter key: Too narrow tolerance will cause
Length error and stop in the batch.
5. Home: Press to return to ”Main” menu.
LENGTH CONTROL
LENGTH ERROR
00000
0000000
00
00
HOME
5
4
3
2
1
Requested length mm
mm
mm
mm
Ext.Current Length
Length tolerance +
Length tolerance -

Page 18
AUTOCUT 5-32CTS USER MANUAL EDITION II 2015-01-16
5.5.6 Machine parameter menu
This menu is for calibration of encoder and acceleration and deceleration of feeding belt.
The parameters are only accesible with a password and reserved for service personell only.
1. Extern encoder pulses/rev: Set encoder type. Default 1000 pulses.
2. a) Actual mm= true mm (0,5-1,5): Calibration off out put length.
b) Length control calibration: Calibration of Length control function.
3. Acceleration (50-5000msec): Set the acceleration time for the belt.
4. Deceleration (50-5000msec): Set the deceleration time for the belt.
5. Home: Press to return to ”Main” menu.
MACHINE PARAMETER
00000
0000000
00
00
HOME
5
4
3
2
1
Extern encoder pulses/rev Pulses
mm
msec
msec
Ext.Current Length
Acceleration (50-5000 msec)
Deceleration (50-5000 msec)

Page 19
AUTOCUT 5-32CTS USER MANUAL EDITION II 2015-01-16
5.5.7 Manual handle output menu
This menu has got two pages from which electric and pneumatic functions can be tested.
Start with green buttons and stop with red buttons.
Caution! Functions will start immediately, make sure that there will be no risk for injuries
or damages.
(1)
(2)
1. Hosereel / Hosefeeding unit:
Forward / Reverse
2. Belt feed motor:
Forward / Reverse
3. Cut motor: Caution!
Start / Stop
4. Conveyor motor:
Start / Stop
5. View page 2
6. Return to ”Main” menu
7. Prebend ap cylinder:
On / Off
8. Belt unit cylinder:
On, Low pressure
On, High pressure
Off
9. Cut blade cylinder:
Up
Speed1
Speed2
Speed3
10. KnifeCut cylinder (option):
On/Off
11. Return to page 1
12. Return to ”Main” menu
PREBEND
CYL.ON
PREBEND
CYL.OFF
BELT UNIT
ON LOW
BELT UNIT
ON HIGH
BELT UNIT
CYL.RETURN
CUT BLADE
SPEED 5
MARKING
MARK
CUT BLADE
SPEED 2
LAMP
TEST
CUT BLADE
SPEED 3
CUT
START
KNIFECUT
ON
HOME
PREV.
11 12
MANUAL HANDLE OUTPUT
HOSEREEL
FORWARD
BELT
FORWARD
BELT
REVERSE
CUT MOTOR
START
STOP
OFF OFF
STOP
CONVEYOR
START
HOSEREEL
REVERSE
HOMENEXT
1 2 3
65
4
7 8 9 10
MANUAL HANDLE OUTPUT

Page 20
AUTOCUT 5-32CTS USER MANUAL EDITION II 2015-01-16
5.5.8 Timers menu
This menu is for setting delay time for the off signal for idling of the cut motor and the
conveyor belt motor.
1. Delay time cut: Set the wanted idling time for the cut motor when cut sequence not is
running.
2. Delay time conveyor: Lengthen the conveyor feeding time. Value ”0” = start and stopp
is the same as for the belt unit in cutting machine.
3. Home: Return to ”Main” menu.
TIMERS
HOME
3
2
1
Delay time Cut Sec
Sec
Delay time Conveyor
00000
00000