HyperX Cloud Stinger Wireless HX-HSCSW-BK User manual

Document No. 480HX-HSCSW.A01
HyperX Cloud Stinger WirelessTM
Page 1 of 14
HyperX Cloud Stinger WirelessTM
Part numbers
HX-HSCSW-BK

Document No. 480HX-HSCSW.A01
HyperX Cloud Stinger WirelessTM
Page 2 of 13
TABLE OF CONTENTS
Overview ................................................................................................................................... 3!
Specifications .......................................................................................................................... 4!
Headset Controls ..................................................................................................................... 5!
Headset Battery Indicator LED States.................................................................................... 6!
Headset Charging .................................................................................................................... 7!
Using with PS4™ ..................................................................................................................... 8!
Using with Nintendo Switch™ ................................................................................................ 9!
Using with PC ......................................................................................................................... 10!
Manually Pairing Headset and Wireless Adapter ................................................................ 12!

Document No. 480HX-HSCSW.A01
HyperX Cloud Stinger WirelessTM
Page 3 of 13
Overview
A. Volume wheel
B. Swivel to mute microphone
C. USB charge port
D. Power button
E. Wireless adapter
F. USB charge cable
G. Wireless status light
H. Battery indicator LED

Document No. 480HX-HSCSW.A01
HyperX Cloud Stinger WirelessTM
Page 4 of 13
Specifications
Headphone
Driver: Dynamic, 50mm with neodymium magnets
Type: Circumaural, Closed back
Frequency response: 20Hz-20,000Hz
Impedance: 32 Ohm
Sound pressure level: 109dBSPL/mW at 1kHz
T.H.D.: < 2%
Weight: 270g
Cable length and type: USB charging cable (1m)
Microphone
Element: Electret condenser microphone
Polar pattern: Noise-cancelling
Frequency response: 100Hz-7,000 Hz
Sensitivity: -47dBV (0dB=1V/Pa,1kHz)
Battery life*
17 hours
Battery charge time
About 2.5 hours
Wireless Range**
2.4 GHz
Up to 12 meters
*Tested at 50% headphone volume
**Wireless range may vary due to environmental conditions

Document No. 480HX-HSCSW.A01
HyperX Cloud Stinger WirelessTM
Page 5 of 13
Headset Controls
Power button
Hold the power button for 3 seconds to power on/off the headset.
Volume wheel
Move the volume wheel towards the + sign to increase the volume.
Move the volume wheel towards the – sign to decrease the volume.
Microphone mute
Swivel the microphone upwards to mute the microphone.
Swivel the microphone downwards to unmute the microphone.
Mute on
Mute off

Document No. 480HX-HSCSW.A01
HyperX Cloud Stinger WirelessTM
Page 6 of 13
Headset Battery Indicator LED States
The headset battery indicator LED indicates the current state of the headset.
Battery Indicator LED
Headset Status
Slow breathing orange
Searching for wireless adapter
Fast blinking red and green
Pairing mode
Solid green
90% – 100% battery remaining
Blinking green
50% – 90% battery remaining
Blinking orange
25% – 50% battery remaining
Blinking red
<25% battery remaining

Document No. 480HX-HSCSW.A01
HyperX Cloud Stinger WirelessTM
Page 7 of 13
Headset Charging
When the headset is connected to a charger with the USB charge cable, the battery indicator LED will
indicate the charge status. The headset will take approximately 2.5 hours to fully charge.
Battery Indicator LED
Charging Status
Solid green
100% charged
Breathing green
50% – 99% charged
Breathing orange
25% – 50% charged
Breathing red
<25% charged

Document No. 480HX-HSCSW.A01
HyperX Cloud Stinger WirelessTM
Page 8 of 13
Using with PS4™
1. Connect the wireless adapter to a front USB port on the PS4™ system.
2. Power on the headset.
3. When the wireless adapter status light is solid, the headset is now connected to the adapter.
To ensure the headset is configured with the most optimal settings on the PS4, follow the steps below:
1. From the PS4 main menu, go to Settings > Devices > Audio Devices
2. Set Input Device to USB Headset (HyperX Cloud Stinger Wireless)
3. Set Output Device to USB Headset (HyperX Cloud Stinger Wireless)
4. Set Output to Headphones to All Audio
5. Set Volume Control (Headphones) to 100% volume

Document No. 480HX-HSCSW.A01
HyperX Cloud Stinger WirelessTM
Page 9 of 13
Using with Nintendo Switch™
1. Connect the wireless adapter to a side USB port on the Nintendo Switch dock.
2. Power on the headset.
3. When the wireless adapter status light is solid, the headset is now connected to the adapter.
You may set the USB audio volume on Switch to maximum by using the volume buttons on the Switch
console, then adjust the volume with the headset volume wheel.

Document No. 480HX-HSCSW.A01
HyperX Cloud Stinger WirelessTM
Page 10 of 13
Using with PC
1. Connect the wireless adapter to a USB port on the PC.
2. Power on the headset.
3. When the wireless adapter status light is solid, the headset is now connected to the adapter.
To ensure the headset is configured correctly on the PC, follow the steps below:
1. Right-click on the sound icon on the system
tray and select Sounds.