Hytronik HIR22 User manual

Hytronik PIR motion sensor
352
Stand-by power
EMC standard (EMC)
Safety standard (LVD)
Certication
Resistive
EN55015, EN61000
Semko, CB, CE , EMC, LVD, SAA
1600W
EN60669-1, EN60669-2-1
Model No. HIR22
220~240VAC 50/60Hz
Mains voltage
Load ratings:
<0.5W
Input Characteristics
Safety and EMC
800W
Capacitive
Sensor Data
HIR22
Operation temperature Ta: -20
O
C ~ +50
O
C
Environment
IP20
IP rating
Model No.
360O
5m (maximum)
PIR detectionSensor principle
Detection range
Detection angle
Mounting height
(O x H) 10m x 3m
30sWarming-up
HIR22
Daylight Harvest with Remote Control
Flush Mount PIR Motion Sensor
Technical Data
(1) Sensor inset
(2) Lens pluggable
(3) Protection cover (covers the
high-voltage terminals).
(4) Ceiling (drill hole Ø70mm).
Infrared receiver
Photocell
LED indicator
PIR
Rotary switch preset
1
3
4
2
70mm 64.7
68.1 73.3
56
Blind
Note: the blind can be plugged to the cover for
reducing detection angle if necessary.
Ø85
-PPQJO
-PPQPVU
"NCJFOUEBZMJHIU
UISFTIPME
0OF,FZ
$PNNJTTJPOJOH
1IPUPDFMM
*OUFMMJHFOU
3PUBSZ4XJUDI
1SPHSBNJOH
Mechanical Structure
PIR



%FUFDUJPO1BUUFSO
IP20
www.hytronik.com

Hytronik PIR motion sensor
353
Daylight Harvest
Light will not switch on
when natural light is
sufcient, even there is
motion detected.
The light switches on
automatically with
presence when natural
light is insufcient.
The light turns on at full or dims to maintain the lux level. The light output
regulates accroding to the level of natural light available.
The light dims to stand-by
period after hold-time and
stays on selected minimum
dimming level.
The light switches off when
the ambient natural light is
sufcient.
The light switches off
completely after the
stand-by period.
Functions and Features
1
Note:
The Light automatically dims down and
eventually turns off if the natural light lux
level exceeds the daylight threshold.
However, if the stand-by period is preset
at “+∞”, the xture never switches off
but dim to minimum level, even the
natural light is sufcient.
Manual Override
2
* Short Push (<1s): on/off function;
On →Off: the light turns off immediately and cannot be triggered ON by motion until the expiration of pre-set hold-time. After this
period, the sensor goes back to normal sensor mode.
Off →On: the light turns on and goes to sensor mode, no matter if ambient Lux level exceeds the daylight threshold or not.
* Long Push (>1s): adjust the target lux level by turning the light up or down. Both the adjustment on remote control and push switch
can overwrite each other. The last adjustment remains in memory.
Note: if end-user do not want this manual override function, just leave the “push” terminal unconnected to any wire.
With the help of push-switch, this sensor can be over-ridden by the end-user to manually switch on/off the light, or adjust the target lux
level by push-switch, which makes the product more user-friendly and offers more options to t some extra-ordinary demands:
Semi-auto Mode (Absence Detection)
3
It is easy to forget to switch off the light, in ofce, corridor, even at home. And in many other cases, people do not want to have a
sensor to switch on the light automatically, for example, when people just quickly pass-by, there is no need to have the light on. The
solution is to apply this “absence detector”: motion sensor is employed, but only activated on the manual press of the push-switch, the
light keeps being ON in the presence, and dims down in the absence, then switches off in the long absence.
Note: end-user can choose either function or function for application. Default function is manual override.
23
www.hytronik.com

Hytronik PIR motion sensor
354
Press the buttons to select light output at 80% (at initial 10,000 hours) or 100%.
Note: “Sensor off” and “Twilight” functions are disabled.
zero-cross point
Alternating current
Zero-cross Relay Operation
Designed in the software, sensor switches on/off the
load right at the zero-cross point, to ensure that the
in-rush current is minimised, enabling the maximum
lifetime of the relay.
4
Double L N terminal makes it easy for wire loop-in and loop-out, and saves the cost of terminal block and assembly time.
Loop-in and Loop-out Terminal
5
Settings (Remote Control HRC-11)
HRC-11
Press button “RESET”, all settings go back to rotary switch settings.
Reset Settings
Permanent ON/OFF function
Press button “ON/OFF” to select permanent ON or permanent OFF mode.
* Press button “AUTO”, “RESET” to quit this mode.
AUTO mode
Press button “AUTO” to initiate automatic mode. The sensor starts working and all
settings remain as before the light is switched ON/OFF.
1. Press button “Shift”, the red LED ashes for indication.
2. Press button “SEMI-AUTO/AUTO” to initiate semi-auto mode. The xture is
manually turned on by pressing the push-switch, and goes off automatically in this
mode. (Absence detection mode)
ON/
OFF
SEMI-AUTO mode
Press button “Shift”, the LED on the top left corner will ash to indicate mode
selection. All values / settings in RED are valid for 20 seconds.
Shift Button
Power output
www.hytronik.com

Hytronik PIR motion sensor
355
Press the buttons to adjust the light brightness to reset the target lux level.
Brightness +/-
Scene program - 1-key commissioning
Detection range
Press buttons in zone “Detection range” to set detection range at 100% / 75% / 50% / 10%.
Press buttons in zone “ Daylight threshold” to set daylight sensor / target lux level at 50Lux / 100Lux / 300Lux / 500Lux / Disable.
Note: 2lux / 10lux are disabled.
To set daylight sensor at 100Lux / 300Lux / 500Lux, press “Shift” button rst.
Daylight threshold
1. Press button “Shift”, the red LED starts to ash.
2. Press button “Ambient”, the surrounding lux level is sampled and set as the new daylight threshold / target lux level.
Ambient daylight threshold
Hold-time
Press buttons in zone “hold-time” to set the hold-time at 2s / 30s / 1min / 5min / 10min / 15min / 20min / 30min.
Note: 1. To set hold-time at 30s / 5min / 15min / 30min, press “Shift” button rst.
2. 2s is for testing purpose only, stand-by period and daylight sensor settings are disabled in this mode.
*To exit from Test mode, press button “RESET” or any button in “Hold-time”.
1. Press button “Start” to program.
2. Select the buttons in “Detection range”, “Daylight threshold”, “Hold-time”, “Stand-by time”, “Stand-by dimming level” to set all
parameters.
3. Press button “Memory” to save all the settings programmed in the remote control.
4. Press button “Apply” to set the settings to each sensor unit(s).
For example, to set detection range 100%, daylight threshold Disable, hold-time 5min, stand-by time +∞, stand-by dimming level 30%, the steps should be:
Press button “Start”, button ”100%”, “Disable”, “Shift”, “5min”, “Shift”, “+∞”, “30%”, “Memory”. By pointing to the sensor unit(s) and pressing “Apply”, all
settings are passed on the sensor(s).
Dual tech & RF mode
Stand-by dimming level
Stand-by time (corridor function)
Press buttons in zone “stand-by time” to set the stand-by period at 0s / 10s / 1min / 5min / 10min / 30min / 1h / +∞.
Note: “0s” means on/off control; “+∞” means bi-level control, the xture is 100% on when there is motion detected, and remains at the stand-by dimming level
when no presence after motion hold-time.
Press the button in zone “stand-by dimming level” to set the stand-by dimming level at 10% / 20% / 30% / 50%.
All buttons are disabled.
www.hytronik.com

Hytronik PIR motion sensor
356
A rotary switch is built inside the sensor for scene
selection / fast programming. Total 16 channels
are available:
Rotary switch preset
Rotary Switch Preset
Note: settings can also be changed by remote control
HRC-11. The last action controls.
0 5s100% Disable
1 1min100% 50Lux
2 5min100% 50Lux
3 5min100% 75Lux
4 5min100% 100Lux
5 5min100% 200Lux
6 10min100% 50Lux
7 10min100% 75Lux
8 10min100% 100Lux
9 10min100% 200Lux
A 20min100% 100Lux
B 20min100% 200Lux
C 30min100% 100Lux
D 30min100% 200Lux
E30min100% 400Lux
F5s100%
10%
10%
10%
10%
10%
30%
10%
10%
10%
30%
10%
30%
10%
30%
50%
10%100Lux
10s
5min
10min
+∞
+∞
+∞
30min
+∞
+∞
+∞
1h
+∞
+∞
+∞
+∞
10s
Detection
range
Channel Hold-time Stand-by
time
Stand-by
dim level
Daylight
sensor
Wiring Diagram
LED Driver
HIR22
L
N
Detection Pattern
1-10V
+
-
P
L
N
1-10V
+ -
L’ N N L LED+
LED -
walking across 10m
walking towards 8m
www.hytronik.com