Hytronik HIM38/RF Quick guide

RF WIRELESS DUAL SENSE SENSOR FOR HIGH BAY HIM38/RF (1-10V OUTPUT)
1. Technical Specifications
Product type RF wireless dual sense 1-10V motion sensor (tri-level control)
Operating voltage 220-240VAC 50/60Hz
Rated load Capacitive:800VA
Resistive:1000W
Power consumption < 1.5W
Detection angle 360o
Detection area (Max.)*
Detection range 10% / 50% / 75% / 100%
Hold time 2s / 30s / 1min / 5min / 10min / 15min / 20min / 30min
Stand-by time 0s / 10s / 1min / 5min / 10min / 30min / 1h / +∞
Stand-by dimming level 10% / 20% / 30% / 50%
Daylight threshold 2 ~ 500Lux, Disable
RF transmission distance 30 meters in the open area
RF frequency 868MHz (FSK mode)
Warming up time 30s
Operating temperature -20oC ~ +50oC
IP rating IP65
Sensor mode HF, PIR, HF+PIR, HF / PIR
3. Rotary Switch for RF grouping
4. Functions
The built-in daylight sensor can read ambient natural light and switch off the fixture automatically
whenever artificial light is not required (natural light lux level exceeds daylight threshold).
Note: if the stand-by time is preset at "+∞", the fixture never switches off even when natural light
is sufficient.
4.2 Lux Off Function
Hytronik builds this function inside the motion sensor to achieve tri-level control, for some areas it requires
a light change notice before switch-off.
It offers 3 levels of light: 100%-->dimmed light-->off; and 2 periods of selectable waiting time: motion
hold-time and stand-by period; Selectable daylight threshold and freedom of detection area.
4.1 Tri-level Control (Corridor Function)
2. Installation
Warnings:
1. Installation must be carried out by a qualified engineer in accordance with
local regulations.
2. Disconnect power supply before installing.
3. Install to a solid surface - vibrations may cause mis-triggering.
4. Ensure environmental conditions are suitable for electronic equipment
Rotary switch for RF grouping
(Please see the location in 2. Installation)
15 channels are available for fast grouping via rotary switch. By simply selecting the same channel on each
unit, the grouping is automatically completed.
Noted: channel "0" is not for fast grouping, and sensors can only be grouped by remote control.
The light will flash ONCE rapidly after receiving the command from the remote controller.
Note: There is no load indication (the light will not flash) when button ON/OFF, POWER 100%
or POWER 80% is pressed.
4.3 Load Indication
Installation and Instruction Manual
TM
5. Wiring Diagram
Brown
Blue
Red
Black
Grey
HIM38/RF
L
N
1-10V
+
1-10V -
LED
Driver
L
N
Installation Height : 15m
Detection Range (Ø) : 24m
HIM38/RF-20230818-A1
Subject to change without notice.
HIM38/RF-20230818-A1
Subject to change without notice.
A. Ceiling mount
B. Screw to the Luminaire by conduit
C. Attach to the shade by clamp
Sensor module
PIR
LED indicator
Infrared receiver Rotary switch for RF grouping
Cable entry
Installation rack
Daylight sensor
81.5
4.1
66.6
91.5
80.7
75
4.1
59.3
73.5
57.3
47.5
24.5
163.2
33.7
28.5
4.5
15
96.8
66.6
ぶ4.5
93.8
84.5
59.3
ぶ29
Sensor module
PIR
LED indicator
Infrared receiver
Rotary switch for RF grouping
Angle adjustment
Luminaire clamp
Daylight sensor
Cable entry
Sensor module
PIR
LED indicator
Infrared receiver Rotary switch for RF grouping
Daylight sensor
59.6
66.6
89.9
0.825”
75
64
43.8
43
73.5
59.3 57.3
47.5
Sensoroff Twilight
Shift
AUTO
100% 75% 50% 10%
2Lux
100Lux
10Lux
300Lux
50Lux
500Lux
Disable
Ambient
Memory Apply
Test
2s
30s
1min 10min
5min 15min 30 min
0s
10s 1h
10% 20% 30% 50%
Dualtech & RF mode
SEMI-AUTO
Hold-time
Stand-bytime
Stand-bydimming level & Auto-config.
Daylightthreshold
Sensitivity& More functions
RX
STBY%
PIR
RX
100%
HF HF+PIR HF/PIR
Shift Send
5min 30min
20min
Power
100%
Power
80%
1min 10min
+
Start
RESET
ON
OFF
24h 30s
12h 4h
Learn
Erase Transmit
Brightness
CCT-
CCT+
Tri-level Harvest Master
×
Exp1 Exp2 Lux off
6. RF grouping by remote controller
Step1
Short press “Learn/Erase” button on RC to the receiver to activate pairing mode, and the LED
indicator on receiver unit will flash slowly.
Note: up to 30 units can be paired.
Step3
The receiver unit
LED indicator flashes rapidly
Short press “Transmit” button on RC to the commander, the LED indicator on commander unit
will flash for 3 times to send the transmission signal.
Erase:
Long press “Learn/Erase” button for 3s to the sensor unit, the indicator rapidly flashes 12
times, all commands it has received before will be erased.
The receiver unit
LED indicator flashes slowly
Upon receiving the transmission signal, the indicator on receiver unit will flash quickly then
slowly to indicate the success of pairing. One more short press on “Learn/Erase” button to the
receiver unit to complete the pairing process, the receiver unit will quit the pairing mode.
The sensor can serve as both commander and receiver, simply repeat above steps the other
way around.
Short press ”Learn
/Erase” button
Short press ”Learn
/Erase” button
Step2
The commander unit
LED indicator flash 3 times LED indicator flashes quickly then slowly
when RF signal is received successfully
The receiver unit
Short press
”Transmit” button
123
7. Three Options for PIR Lens and Detection Patterns
(End user can choose the suitable lens in real application for various requirements)
* For single person walking across, the detection range is reduced by 1/3.
Detection pattern for human
PIR detection: Ø = 24m (max.) HF detection: Ø = 24m (max.) PIR detection: Ø = 24m (max.) HF detection: Ø = 24m (max.) PIR detection: Ø = 24m (max.) HF detection: Ø = 24m (max.)
Detection pattern for forklift
15m(forklift)
PIR & HF: max. 24m
PIR
HF
PIR & HF: max. 24m
PIR
HF
15m(forklift)
PIR & HF: max. 24m
PIR
HF
15m(forklift)
HF detection: Ø = 14m (max.) PIR detection: Ø = 20m (max.) HF detection: Ø = 14m (max.) PIR detection: Ø = 20m (max.) HF detection: Ø = 14m (max.) PIR detection: Ø = 20m (max.)
PIR
HF
PIR: max. 20m
HF : max. 14m
12m(human)
PIR
HF
PIR: max. 20m
HF: max. 14m
12m(human)
PIR
HF
PIR: max. 20m
HF: max. 14m
12m(human)
Sensoroff Twilight
Shift
AUTO
100% 75% 50% 10%
2Lux
100Lux
10Lux
300Lux
50Lux
500Lux
Disable
Ambient
Memory Apply
Test
2s
30s
1min 10min
5min 15min 30 min
0s
10s 1h
10% 20% 30% 50%
Dualtech & RF mode
SEMI-AUTO
Hold-time
Stand-bytime
Stand-bydimming level & Auto-config.
Daylightthreshold
Sensitivity& More functions
RX
STBY%
PIR
RX
100%
HF HF+PIR HF/PIR
Shift Send
5min 30min
20min
Power
100%
Power
80%
1min 10min
+
Start
RESET
ON
OFF
24h 30s
12h 4h
Learn
Erase Transmit
Brightness
CCT-
CCT+
Tri-level Harvest Master
×
Exp1 Exp2 Lux off
Sensoroff Twilight
Shift
AUTO
100% 75% 50% 10%
2Lux
100Lux
10Lux
300Lux
50Lux
500Lux
Disable
Ambient
Memory Apply
Test
2s
30s
1min 10min
5min 15min 30 min
0s
10s 1h
10% 20% 30% 50%
Dualtech & RF mode
SEMI-AUTO
Hold-time
Stand-bytime
Stand-bydimming level & Auto-config.
Daylightthreshold
Sensitivity& More functions
RX
STBY%
PIR
RX
100%
HF HF+PIR HF/PIR
Shift Send
5min 30min
20min
Power
100%
Power
80%
1min 10min
+
Start
RESET
ON
OFF
24h 30s
12h 4h
Learn
Erase Transmit
Brightness
CCT-
CCT+
Tri-level Harvest Master
×
Exp1 Exp2 Lux off

8. Descriptions of the Button Functions (remote control HRC-11)
9. Troubleshooting
MALFUNCTION CAUSE REMEDY CAUSE REMEDY
The fixture does not light up
The fixture is always on
Check detection area setting
The fixture is on when it should not
Incorrect daylight threshold setting
Continous movement in the detection zone
Sudden change in temperature due to weather (wind, rain, snow) or air
expelled from fans, open windows
Detection zone not targeted
Faulty fixture
No power supply
Adjust daylight threshold setting
Replace fixture
Check power to sensor
Check detection area setting
Adjust zone, change installation site
Press button “ON/OFF” to select permanent ON or permanent OFF mode.
* Press button “AUTO”/“RESET” to exit this mode.
HRC-11
Press button “Shift”, the LED on the top left corner is on to indicate mode selection. All
values / settings in RED are valid for 20 seconds.
For example, to set detection range 100%, daylight threshold Disable, hold-time 5min,
stand-by time +∞, stand-by dimming level 30%, the steps should be:
Press button “Start”, button ”100%”, “Disable”, “Shift”, “5min”, “Shift”, “+∞”, “30%”,
“Memory”. By pointing to the sensor unit(s) and pressing “Apply”, all settings are passed
on the sensor(s).
Press these two buttons to adjust the light output brightness and set a new target lux level.
The daylight sensor can measure ambient daylight level and ignore the LED light, so as to
calculate how much articial light is needed to maintain the target lux level.
Lux off
Exp 1
Exp 2
Press button “AUTO” to initiate automatic mode. The sensor starts working and all settings
remain as before the light is switched ON/OFF;
Press buttons in zone “Power out” to select the light output at 80% (at initial 10,000 hours)
or 100%.
1. Press button “Start” to program.
2. Select the buttons in “Detection range”, “Daylight threshold”, “Hold-time”, “Stand-by
time”, “Stand-by dimming level” to set all parameters.
3. Press button “Memory” to save all the settings programmed in the remote control.
4. Press button “Apply” to set the settings to each sensor unit(s).
"Exp" refer to Expansion, these two buttons are reserved functions and pending future
development.
In AUTO modes, press buttons in zone “Detection range” to set detection range at
100%/75%/50%/10%.
1.Press button “Shift”, the red LED on.
2. Press buttons “Tri-level” or “Daylight harvest” to shift between Tri-level control
mode and Daylight harvest mode.
Master
100% 75%
50% 10%
Tri-level
Harvest
Sensitivity & More functions
CCT+
CCT-
Sensor off Twilight
Shift
AUTO
100% 75% 50% 10%
2 Lux
100 Lux
10 Lux
300 Lux
50 Lux
500 Lux
Disable
Ambient
Memory Apply
Test
2 s
30 s
1 min 10 min
5 min 15 min 30 min
0s
10 s 1h
10% 20% 30% 50%
Dual tech & RF mode
SEMI-AUTO
Hold-time
Stand-by time
Stand-by dimming level & Auto-config.
Daylight threshold
Sensitivity & More functions
RX STBY%
PIR
RX 100%
HF HF+PIR HF/PIR
Shift Send
5 min 30 min
20 min
Power
100%
Power
80%
1 min 10 min +
Start
RESET
ON
OFF
24h 30s 12h 4h
Learn
Erase Transmit
Brightness
CCT-
CCT+
Tri-level Harvest Master ×
Exp 1 Exp 2 Lux off
This key is not appliable on this product.
This key is not appliable on this product.
This key is not appliable on this product.
This key is not appliable on this product.
This key is not appliable on this product.
Press button “RESET”, perform DIP Switch/Rotary Switch settings.
The default settings are: Auto mode; Detection range 100%; Hold-time 1min; Stand-by
time 5 min; Stand-by dimming level 20%; Daylight sensor disable; RX 100%.
HRC-11
Sensor off Twilight
Shift
AUTO
100% 75% 50% 10%
2 Lux
100 Lux
10 Lux
300 Lux
50 Lux
500 Lux
Disable
Ambient
Memory Apply
Test
2 s
30 s
1 min 10 min
5 min 15 min 30 min
0s
10 s 1h
10% 20% 30% 50%
Dual tech & RF mode
SEMI-AUTO
Hold-time
Stand-by time
Stand-by dimming level & Auto-config.
Daylight threshold
Sensitivity & More functions
RX STBY%
PIR
RX 100%
HF HF+PIR HF/PIR
Shift Send
5 min 30 min
20 min
Power
100%
Power
80%
1 min 10 min +
Start
RESET
ON
OFF
24h 30s
12h 4h
Learn
Erase Transmit
Brightness
CCT-
CCT+
Tri-level Harvest Master ×
Exp 1 Exp 2 Lux off
In AUTO modes, press buttons in zone “hold-time” to set the hold-time at 2s / 30s / 1min
/ 5min / 10min / 15min / 20min / 30min.
Dual tech & RF mode
Press buttons in zone “stand-by time” to set the stand-by period at 0s / 10s / 1min / 5min
/ 10min / 30min / 1h / +∞.
Note: 1. To set stand-by-time at 10s/ 5min / 30min / 1h, press “Shift” button rst.
2. “0s” means on/off control;
3. “+∞” means bi-level control, the xture is 100% on when there is motion detected, and remains at the
stand-by dimming level when no presence after motion hold-time. Only when the stand-by time is set in "+∞" and
the ambient lux level is below the target lux level, the lux will auto-on.
Press the button in zone “stand-by dimming level” to set the stand-by dimming level at 10%
/ 20% / 30% / 50%.
Press buttons in zone “Daylight threshold” to set daylight sensor at 2Lux/ 10Lux / 50Lux
/ 100Lux / 300Lux/500Lux / Disable.
1. Press button “Shift”, the red LED on.
2. Press button “Ambient”, the surrounding lux level is sampled and set as daylight threshold
/ target Lux level.
Note: To set daylight sensor at 100Lux / 300Lux/500Lux , press “Shift” button rst.
2 Lux 100 Lux
10 Lux 300 Lux
50 Lux 500 Lux
Disable
Ambient
Test
2 s
30 s
1 min
10 min
5 min
15 min
30 min
20 min
0s 10 s
1h
5 min
30 min
1 min
10 min
+
10% 20%
30% 50%
PIR
HF
HF+PIR
HF/ PIR
Learn
Erase
Transmit
Note: 1. To set hold-time at 30s / 5min / 15min / 30min, press “Shift” button rst.
2. 2s is for testing purpose only, stand-by period and daylight sensor settings are disabled in this mode.
*To exit from Test mode, press button “RESET” or any button in “Hold-time”.
Short press”learn/erase” button to activate pairing mode, then press ”transmit” on a
primary mode and all the receiver modules will beep 3 times in 1s to indicate the
success of paring. Long press the “learn/erase” button for 3s will erase all the commands
received previously.
1.Press button “Shift” ,the red LED on.
2. Choose one of the four detecion mode “HF only”, “PIR only”, “HF& PIR” or“ HF/PIR”.
Stand-by time mode
Hold-time mode
Daylight threshold
Stand-by dimming level & Auto-cong.
24h 12h
4h 30s
This key is not appliable on this product.
RX 100%
RX STBY%
Press button RX100%, the light on receiver unit is 100% upon receiving RF on singal;
Press button “RX STBY%”, the light(s) oes to pre-set stand-by dimming level directly.
HIM38/RF-20230818-A1
Subject to change without notice.
HIM38/RF-20230818-A1
Subject to change without notice.