Hytronik Dual Sense HIM31 User manual

Subject to change without notice. Edition: 26 Feb. 2020 Ver. A0 Page 1/7
HIM31
HF and PIR, 1-10V Dimming with Remote Control
IP65 High Bay Dual Sense Sensor
Stand-by power
EMC standard (EMC)
Safety standard (LVD)
Certication
Radio Equipment (RED)
Resistive
EN55015, EN61000
EN60669, AS/NZS60669
Model No. HIM31
220-240VAC 50/60Hz
Mains voltage
Load ratings:
EN300440, EN301489-1,
EN62479
<1W
Input Characteristics
Safety and EMC
800VA
1000W
Capacitive
Sensor Data
Operation temperature Ta: -20
O
C~ +50
O
C
Environment
IP65
IP rating
30sWarming-up
Technical Data
Mechanical Structures and Installations
For more details, please refer to user manual.
TM
HIM31
Model No.
<0.2mW (HF)
5.8GHz +/- 75MHz (HF)
High Frequency (microwave), PIR
4 modes: PIR, HF, PIR+HF, PIR/HF
Sensor principle
Operation frequency
Transmission power
Sensor mode
Detection range
Detection angle
Max. ( Ox H) 18m x 15m
360O
Semko, CB, CE , EMC, RED IP65RED
A. Ceiling mount
Sensor module
PIR
Daylight sensor
LED indicator Infrared receiver
Rotary switch for programing
Cable entry
Installation rack
81.5
4.1
66.6
91.5
80.7
75
4.1
59.3
73.5
57.3
47.5
24.5

Subject to change without notice. Edition: 26 Feb. 2020 Ver. A0 Page 2/7
It’s commonly known Microwave and Infrared are main detecting technologies in lighting controls. Both have the advantage and
disadvantage for industrial applications.
The remedy is to create Dual Sense by combining both technologies to make use of the advantage and bypass the disadvantage.
* sensitive to minor motion.
* sensitive to radial movement.
* can be reected by objects hence covering big detection area
* resilient to heat source, smoke and and air conditioner.
* penetrates walls, picks up motions outside of the ofce area;
* back wave detection, false trigger by motions at the back.
* can be false triggered by ventilation fans, water pipe, elevators
etc. in industrial application.
* no penetration, conned detection area.
* sensitive to tangential movement.
* resilient to motion object which has no heat radiation.
* can be false triggered by air conditioner, smoke and
other heat sources.
Dual Sense Introduction
HF PIR
Advantage
Disadvantage Disadvantage
Advantage
C. Attach to the shade by clamp
B. Screw to the Luminaire by conduit
Cable entry
Sensor module
PIR
Daylight sensor
LED indicator Infrared receiver
Rotary switch for programing
59.6
66.6
89.9
0.825”
75
64
43.8
43
59.3
73.5
35.2
57.3
47.5
Sensor module
PIR
Daylight sensor
LED indicator Infrared receiver
Rotary switch for programing
Angle adjustment
Luminaire clamp
163.2
33.7
28.5
4.5
15
96.8
66.6
ぶ
4.5
93.8
84.5
59.3
ぶ
29
Note:We recommend the mounting distance between sensor to sensor should be more than 2m to prevent sensors
from false-triggering.

Subject to change without notice. Edition: 26 Feb. 2020 Ver. A0 Page 3/7
Intelligent Photocell (daylight detection prior to motion detection)
1
The built-in photocell will also automatically turn off the light when the ambient natural light exceeds the programmed lux level for
more than 5min, regardless of whether motion is detected or not. This feature can be disabled if it is required that the xture stays at
dimmed level during absence.
With insufcient natural light, the sensor
switches on the light automatically when
presence is detected.
With sufcient natural light, the light
does not switch on when presence is
detected.
The sensor switches off the light when
natural light is sufcient, even with
presence.
Note: if the stand-by time is preset at "+∞", the xture never switches off but stays at preset dimming level even when natural light is sufcient.
9
0
15
Detection Pattern
Ambient daylight
threshold
One-Key
Commissioning
Photocell
Intelligent
Rotary Switch
Programing
Functions and Features
* HF: Microwave only
* PIR: PIR mode only
* HF+PIR: both PIR and microwave mode, to decrease the detection capability and detection area. Only when both detections are
activated, the motion is considered valid. This is to prevent the sensor from false trigger by heat source, air conditioner,
ventilation fans, water pipe and elevators etc...
* HF/PIR: either PIR or microwave mode, to increase the detection capability and detection area;
4 optional detection modes via remote control:
Tri-level Control (Corridor Function)
2
Hytronik builds this function inside the motion sensor to achieve tri-level control, for some areas which require a light change notice
before switch-off. The sensor offers 3 levels of light: 100%-->dimmed light (natural light is insufcient) -->off; and 2 periods of
selectable waiting time: motion hold-time and stand-by period; Selectable daylight threshold and freedom of detection area.
zero-cross point
Alternating current
Zero-cross Relay Operation
Designed in the software, sensor switches on/off the
load right at the zero-cross point, to ensure that the
in-rush current is minimised, enabling the maximum
lifetime of the relay.
3

Subject to change without notice. Edition: 26 Feb. 2020 Ver. A0 Page 4/7
A rotary switch is built inside the sensor for scene
selection / fast programming. Total 16 channels
are available:
Rotary switch preset
Rotary Switch Preset
Note: settings can also be changed by remote control
HRC-11. The last action controls.
0 5s100% Disable
1 1min100% 2Lux
2 5min100% 10Lux
3 5min100% 30Lux
4 5min100% 10Lux
5 5min100% 30Lux
6 5min100% Disable
7 10min100% 2Lux
8 10min100% 10Lux
9 10min100% 30Lux
A 10min100% Disable
B 10min75% 30Lux
C 10min50% 10Lux
D 30min100% 50Lux
E30min100% Disable
F5s100%
10%
10%
10%
10%
Disable
10%
30%
10%
10%
10%
30%
10%
10%
10%
30%
10%2Lux
10s
5min
10min
30min
0s
+∞
+∞
10min
30min
+∞
+∞
+∞
+∞
+∞
+∞
10s
Detection
range
Channel Hold-time Stand-by
time
Stand-by
dim level
Daylight
sensor
Press the buttons to select light output at 80% (at initial 10,000 hours) or 100%.
Note: “Sensor off” and “Twilight” functions are disabled.
Settings (Remote Control HRC-11)
Press button “RESET”, all settings go back to rotary switch settings.
Reset Settings
Permanent ON/OFF function
Press button “ON/OFF” to select permanent ON or permanent OFF mode.
* Press button “AUTO”, “RESET” to quit this mode.
The mode will change to AUTO Mode after power failure.
AUTO mode
Press button “AUTO” to initiate automatic mode. The sensor starts working and all
settings remain as before the light is switched ON/OFF.
Note: “Semi-auto” function is disabled.
ON/
OFF
Power output
Press the buttons to adjust the light brightness during hold-time.
Load Indication:
The light will ash ONCE rapidly after
receiving the commamd from the
remote control successfully.
Brightness +/-
&
A
4
4 hhh
HRC-11
Press button “Shift”, the LED on the top left corner is on to indicate mode selection.
All values / settings in RED are valid for 20 seconds.
Shift Button

Subject to change without notice. Edition: 26 Feb. 2020 Ver. A0 Page 5/7
Scene program - 1-key commissioning
Detection range
Press buttons in zone “Detection range” to set detection range at 100% / 75% / 50% / 10%.
Press buttons in zone “ Daylight threshold” to set daylight sensor at 2Lux/ 10Lux / 50Lux / 100Lux / 300Lux / 500Lux / Disable.
Note: To set daylight sensor at 100Lux / 300Lux / 500Lux, press “Shift” button rst.
Daylight threshold
1. Press button “Start” to program.
2. Select the buttons in “Detection range”, “Daylight threshold”, “Hold-time”, “Stand-by time”, “Stand-by dimming level” to set all
parameters.
3. Press button “Memory” to save all the settings programmed in the remote control.
4. Press button “Apply” to set the settings to each sensor unit(s).
For example, to set detection range 100%, daylight threshold Disable, hold-time 5min, stand-by time +∞, stand-by dimming level 30%, the steps should be:
Press button “Start”, button ”100%”, “Disable”, “Shift”, “5min”, “Shift”, “+∞”, “30%”, “Memory”. By pointing to the sensor unit(s) and pressing “Apply”, all
settings are passed on the sensor(s).
1. Press button “Shift”, the red LED starts to ash.
2. Press button “Ambient”, the surrounding lux level is sampled and set as the new daylight threshold.
Ambient daylight threshold
Hold-time
Press buttons in zone “hold-time” to set the hold-time at 2s / 30s / 1min / 5min / 10min / 15min / 20min / 30min.
Note: 1. To set hold-time at 30s / 5min / 15min / 30min, press “Shift” button rst.
2. 2s is for testing purpose only, stand-by period and daylight sensor settings are disabled in this mode.
*To exit from Test mode, press button “RESET” or any button in “Hold-time”.
Stand-by dimming level
Stand-by time (corridor function)
Press buttons in zone “stand-by time” to set the stand-by period at 0s / 10s / 1min / 5min / 10min / 30min / 1h / +∞.
Note: “0s” means on/off control; “+∞” means bi-level control, the xture is 100% on when there is motion detected, and remains at the stand-by dimming level
when no presence after motion hold-time.
Press the button in zone “stand-by dimming level” to set the stand-by dimming level at 10% / 20% / 30% / 50%.
Dual tech & RF mode
1. Press buttons in this zone to select sensor technology.
HF+PIR: the light is on when both HF and PIR sensors are activated.
HF/PIR: the light is on when HF or PIR sensors are activated.
2. Learn / Erase, Transmit, RX100% and RX STBY% are disabled.
Auto-conguration function
All buttons in this zone are disabled.
Note: the function of 24h/12h/4h/30s are disabled.

Subject to change without notice. Edition: 26 Feb. 2020 Ver. A0 Page 6/7
PIR detection: H x D:15 x 18m (max.)
HF detection: H x D:15 x 14m (max.)
PIR
HF
PIR tangential movement 18m
HF walking across 14m
15m
PIR detection: L x W x H:18 x 5 x 15m (max.)
HF detection: H x D:15 x 14m (max. )
PIR
HF
15m
18m
14m
5m
PIR
HF
PIR detection: L x W x H:5 x 18 x 15m (max.)
HF detection: H x D:15 x 14m (max. )
15m
5m
14m
18m
Wiring Diagram
Detection Pattern
End user can choose the suitable PIR lens in real application to fulll various requirements. Three options are offered for selection:
* For single person walking across, the detection range is reduced by 1/3.
HIM31
Brown
LED driver
L
N
1-10V+
1-10V
L
N
Blue
Grey
Red
Black
-

Subject to change without notice. Edition: 26 Feb. 2020 Ver. A0 Page 7/7
Additional Information / Documents
1. Regarding precautions for microwave sensor installation and operation, please kindly refer to
www.hytronik.com/download ->knowledge ->Microwave Sensors - Precautions for Product Installation and Operation
2. Regarding precautions for PIR sensor installation and operation, please kindly refer to
www.hytronik.com/download ->knowledge ->PIR Sensors - Precautions for Product Installation and Operation
3. Regarding Hytronik standard guarantee policy, please refer to
www.hytronik.com/download ->knowledge ->Hytronik Standard Guarantee Policy