Hyundai Lighting Vibelite Neon LED Flex User manual

[email protected] www.hyundailighting.com.auLicensed by HYUNDAI Corporation Holdings, Korea
Imported/Distributed by Azoogi Pty Ltd
Vibelite Neon LED Flex
Installation Manual

[email protected] www.hyundailighting.com.auLicensed by HYUNDAI Corporation Holdings, Korea
Imported/Distributed by Azoogi Pty Ltd
Parameters
CCT
Colour Rendering Index
Total Power
IP Rating
Voltage Rating
Dimmable
Rated Average Design Life
WiFi Frequency
Dimensions
3 years limited warranty.
Visit https://hyundailighting.com.au/terms-and-conditions/
for detailed warranty information.
Email: [email protected]
Before the installation, please ensure the power is off.
5m (HYUSTR001N) LED Strip.
24V DC Power Adaptor with 1.5m
adaptor lead.
LED controller compatible with RF
remote and TUYA app.
RF remote controller with battery.
Mounting clips.
Ensure that surface is clean and dry prior to
applying LED Strip. It is recommended to use
rubbing alcohol and not any household cleaners
or water.
Mount on to the surface using mounting clips.
Plug power adaptor into power point.
To control the Vibelite Neon LED Flex, you can
use Smart Life – Smart Control app on your phone
or tablet or alternatively use the remote control.
HYUSTR001N
RGB
>80
24W
IP65
24V DC
Yes
36,000 Hrs
2.4GHz
10x5000mm
Specications
Package contents
Warranty information
Installation
a
1
b
2
c
3
d
4
e
Vibelite Neon LED Flex Installation Manual
Swallowing may lead
to serious injury in
as little as 2 hours,
due to chemical
burns and potential
perforation of the
oesophagus.
If you suspect your
child has swallowed
or inserted a button
battery, immediately
call the 24-hour
Poisons Information Centre on 13 11 26 (in Australia)
for fast, expert advice.
Examine devices and make sure the battery
compartment is correctly secured. Do not use if
compartment is not secure.
Dispose of used button batteries immediately and
safely.

[email protected] www.hyundailighting.com.auLicensed by HYUNDAI Corporation Holdings, Korea
Imported/Distributed by Azoogi Pty Ltd
In order to start using the RF remote, you must pull the
insulation strip and make sure the remote is pointed in the
line of sight to the receiver.
Short press the button to turn on/off the LED light
Press and hold for 5 seconds to enter the network
conguration mode, and the indicator will ash quickly;
in the fast-ashing state, press and hold for 5 seconds to
enter the hotspot network conguration mode; the network
conguration operation will be completed within 3 minutes
Short press the button to cycle through scenes
Double-click the button to cycle through static, pre-set,
music and other modes
Long press the button to enter/exit the music mode
Play or pause
Click to enter automatic scene mode
Adjust the scene mode
32 preset colours
Click to switch colours (red, green, blue, white)
Short press the button to adjust the speed cyclically
Long press the button to adjust the brightness cyclically
ON/OFF
MUSIC
Play/Pause
AUTO
MODE+/-
Colour Temperature+/-
RGBW
SPEED+/-
Brightness+/-
Download “Smart Life – Smart Living” app from Apple
store or Google Play and install it into your smart phone
or tablet device. Alternatively, scanning the QR code
below will take you to the app’s download page.
Connect the DC jack on one end of the power adapter
to the receiver that is attached to the light. Subsequently,
plug-in the adaptor to an outlet and switch it on.
Download App
Instructions on powering the strip
Registration and Login
Open the “Smart Life – Smart Living” app from your
smart phone.
Follow the prompts to register and login
1
2
Vibelite Neon LED Flex Installation Manual

[email protected] www.hyundailighting.com.auLicensed by HYUNDAI Corporation Holdings, Korea
Imported/Distributed by Azoogi Pty Ltd
Connect the Vibelite Neon LED Flex Strip to a power
source. Once connected, the strip will start blinking
rapidly indicating it is in pairing mode. If not, to enter
pairing mode, turn the strip on and then off 3 to 5 times
with one second wait between turning on and off.
Finally, it must be on. The strip should start blinking
rapidly by now.
Both the mobile phone/tablet and the strips must be
in the same Wi-Fi network while pairing. Once paired,
they can be controlled remotely using the mobile
device.
In the Smart Life - Smart Living app, press the (+)
symbol on the top right-hand corner. When device
window pops up with the light to add, press “Go to
add”. If the device window does not pop up, add the
device manually by selecting “Lighting” tab on the
left panel and choosing “Light Source (BLE + WiFi)”
option. If a pop-up window asking for SSID and
password for your Wi-Fi connection appears, enter the
details (see examples in the next page for reference).
1
2
3
Add device
The frequency of blinking in pairing mode is approx. 2 times
a second. If it is blinking much slower, repeat step 1 until it
starts blinking correctly.
While pairing multiple vibelites at the same time, if some
vibelites are left unpaired, disconnect the power supply to
the paired ones and then pair the remaining ones following
the same process. Once paired, all the vibelites can be re-
connected to the power supply and controlled.
NOTE: Vibelite Neon LED Flex must be connected to 2.4
GHz (not 5 GHz) WiFi connection for smart control. Visit
https://hyundailighting.com.au/switching-your-wi-from-
5ghz-to-2-4ghz/ for steps to switch your Wi-Fi network from
5 GHz to 2.4 GHz.
1
2
3
4
Automatic detection of device and pairing
Vibelite Neon LED Flex Installation Manual

[email protected] www.hyundailighting.com.auLicensed by HYUNDAI Corporation Holdings, Korea
Imported/Distributed by Azoogi Pty Ltd
1
2
3
Manual detection of device and pairing
Pairing process will begin. Do not turn off the strip
while pairing and wait for the pairing process to
complete. If you get a message that says - “Failed
to Add”, repeat the steps from 1 to 3 to pair the
device.
Once the device has been successfully added, you
can begin using it.
4
5
With Smart Life - Smart Living, you can control all your
smart lights remotely from your smartphone app. Whether
you’re in a different room, at work, or halfway across
the world, you can control your smart lights using just a
wireless connection and your smartphone app.
You can congure the Smart Life - Smart Living app
using voice commands through Amazon Alexa or Google
Assistant. This means that you can control all your
lights using voice commands, so you don’t even need to
manually access your Smart Life - Smart Living app. To
control the devices through voice commands, you’ll need
to congure your Smart Life - Smart Living app voice
commands.
Functionalities
Control remotely
Control using voice commands
In “White mode”, you can change the colour temperature
from warm white to daylight using the colour temperature
wheel and the brightness of strip using the scroll bar below
the colour temperature wheel. See example [1] in the next
page for reference.
Tune white colour
Visit https://hyundailighting.com.au/using-google-home-or-
amazon-alexa-to-control-your-lights/ for steps to configure
voice commands for Amazon Alexa or Google Home.
Vibelite Neon LED Flex Installation Manual

[email protected] www.hyundailighting.com.auLicensed by HYUNDAI Corporation Holdings, Korea
Imported/Distributed by Azoogi Pty Ltd
If you have multiple smart LED strips or other smart lights,
you can group and control them simultaneously with a
single tap or voice command. Add all the smart lights to
your Smart Life app individually and select one light. Select
the edit button on the top right corner and “Create Group”.
Then add all the lights you want to add to the group and
press “Save”. Next, name the group for easy recognition
and “Save”. The group will now show up on the home
screen of the app. See example [6] in the next page for
reference.
You can schedule your strip to turn on or off at certain times
of the day using the “schedule” tab on the bottom right
corner. See example [6] in the next page for reference.
You can share the management controls with your friends
and family members so that they can also control the
lights using their smartphones. See example [6] below for
reference.
From the home screen, select the device you want
to remove. Then select the edit button and press the
“Remove Device” button at the bottom.
You can choose from several pre-dened smart
automations scenes or create your own automation scenes
to control the strips. Select “Smart” tab on the bottom
centre of the app home screen to access the smart scenes.
See example [6] in the next page for reference.
Group
Schedule
Share device
Remove device
Tap-to-Run and Automation
[1] [2]
Vibelite Neon LED Flex Installation Manual
There are different pre-set scene modes to choose from
or you can create your own by pressing “Add scene”. See
example [3] in the next page for reference.
In “Colour mode”, you can choose up to 16 million different
colours using the colour wheel and control the brightness
and contrast using the scrolls below. See example [2] in the
next page for reference.
The “Music tab” will enable the lights to change colours
according to the beats of music. See example [5] in the
next page for reference.
Lighting scenes
Choose colours
Sync with Music

[email protected] www.hyundailighting.com.auLicensed by HYUNDAI Corporation Holdings, Korea
Imported/Distributed by Azoogi Pty Ltd
The RCM marking of this product applies to AS/NZS CISPR15 (EMC) “Limits and methods of measurement of radio disturbance
characteristics of electrical lighting and similar equipment”. This product is designed to conform to AS/NZS60598 “Luminaires,
general requirements and tests”.
[5] [6][4]
Vibelite Neon LED Flex Installation Manual
[3]