Hyundai HYW2500P User manual

HYW2500P_HYW3000P_HYW3100P_HYW3100P2_HYW4000P Combined user manual Rev 7.pdf 1 16/12/2015 11:43:50

Page 2
Rev 7
HYW2500P_HYW3000P_HYW3100P_HYW3100P2_HYW4000P Combined user manual Rev 7.pdf 2 16/12/2015 11:43:50

Page 3
Rev 7
1. INTRODUCTION 4
2. PRODUCT IDENTIFICATION 5
3. SAFETY 7 –11
4. PETROL WASHER COMPONENTS 12
5. ASSEMBLY 13
6. PRE-OPERATION CHECK LIST 14
7. STARTING YOUR WASHER 14 –17
8. SHUTTING DOWN YOU WASHER 17 –18
9. QUICK RELEASE NOZZLES 18 - 19
10. TROUBLESHOOTING 20 - 21
11. STORAGE 21 - 22
12. PARTS BREAKDOWN 23 - 30
13. MAINTENANCE 31
14. DECLARATION OF CONFORMITY 32
15. CONTACT DETAILS 33
HYW2500P_HYW3000P_HYW3100P_HYW3100P2_HYW4000P Combined user manual Rev 7.pdf 3 16/12/2015 11:43:50

Page 4
Rev 7
1. INTRODUCTION
Attention: Read through the complete manual prior to the initial use of your
pressure washer.
1.1. Carbon monoxide warning.
1.1.1. Carbon monoxide is a colourless and odourless gas. Inhaling this gas can
cause death as well as serious long term health problems such as brain damage.
The symptoms of carbon monoxide poisoning can include but not limited to the
following; headaches, dizziness, nausea, breathlessness, collapsing or loss of
consciousness.
1.1.2. DO NOT use in an enclosed area or a moving vehicle.
1.2. Using the operating manual.
1.2.1. The operating manual is an important part of your pressure washer and
should be read thoroughly before initial use, and referred to often to make sure
adequate safety and service concerns are being addressed.
1.2.2. Reading the instruction manual thoroughly will help avoid any personal injury
or damage to your machine. The information in this manual will offer you the
most effective tools for cleaning as well as the safest. By knowing how best to
operate this machine you will be better positioned to show others who may
also operate the unit.
1.2.3. This manual contains information for the complete range of pressure washers
and is placed in an order, starting from the safety requirements, to the
operating functions of your machine. You can refer back to the manual at any
time to help troubleshoot any specific operating functions, so store it with the
machine at all times.
1.3. Notice.
1.3.1. Actual pressure released at the point of discharge may vary by machine due
to varying factors including: Volume of water being fed to the machine by the
water source, the inclusion of a Chemical injector in the line, or variations in
Engine performance.
HYW2500P_HYW3000P_HYW3100P_HYW3100P2_HYW4000P Combined user manual Rev 7.pdf 4 16/12/2015 11:43:50

Page 5
Rev 7
2. PRODUCT IDENTIFICATION
2.1. Pressure Washer
2.1.1. If you need to contact an authorised dealer or customer service for
information on servicing, always provide the product model and identification
numbers.
2.1.2. You will need to locate the model and serial number for the machine and
record the information in the places provided below.
Date of purchase
Dealer name
Dealer phone
Model number
Serial number
Engine model number
HYW2500P_HYW3000P_HYW3100P_HYW3100P2_HYW4000P Combined user manual Rev 7.pdf 5 16/12/2015 11:43:50

Page 6
Rev 7
3. SAFETY
3.1. Important safety instructions save these instructions.
3.1.1. WARNING –When using this product basic precautions should always be
followed, including the following:-
3.1.1.1. Read all the instructions before using the product.
3.1.1.2. To reduce the risk of injury, close supervision is necessary when a
product is used near children.
3.1.1.3. Know how to stop the product and bleed pressures quickly. Be
thoroughly familiar with the controls.
3.1.1.4. Stay alert –watch what you are doing.
3.1.1.5. Do not operate the product when fatigued or under the influence of
alcohol or drugs.
3.1.1.6. Keep operating area clear of all persons
3.1.1.7. Do not overreach or stand on unstable support. Keep good footing
and balance at all times.
3.1.1.8. Follow the maintenance instructions specified in the manual.
3.2. Understanding the Machine Safety Labels
3.2.1. The machine safety label shown below is placed on your machine to draw
attention to potential safety hazards.
WARNING!
Do not leave unit running longer than 1 minute
without using or the pump will overheat
Do not let unit freeze.
Always wear eye protection.
injury. Use with Caution.
Warranty is void if you exceed the pre-set pressure
causing severe damage to pump and unloader.
Do not use pressure washer in enclosed space
without ventilation. Carbon Monoxide Kills.
HYW2500P_HYW3000P_HYW3100P_HYW3100P2_HYW4000P Combined user manual Rev 7.pdf 6 16/12/2015 11:43:50

Page 7
Rev 7
3.3. Safety rules.
This is the safety alert symbol. It is used to alert you to potential personal
injury hazards. Obey all safety messages that follow this symbol to avoid
possible injury or death. The safety alert symbol ( ) is used with a signal
word (DANGER, CAUTION, WARNING), a pictorial and/or a safety message to
alert you to hazards.
3.3.1. WARNING - Indicates a hazard which, if not avoided, could result in death or
serious injury.
3.3.2. CAUTION - Indicates a hazard which, if not avoided, might result in minor or
moderate injury.
3.3.3. NOTICE - Indicates a situation that could result in equipment damage.
3.3.4. Follow safety messages to avoid or reduce the risk of injury or death.
EXPLOSION
FIRE
ELECTRICSHOCK
TOXIC FUMES
KICKBACK
HOTSURFACE
FLYINGOBJECTS
SLIPPERY
FALL
FLUIDINJECTION
MOVING PARTS
READMANUAL
3.3.5. WARNING Risk of electrocution, contact with power source can cause electric
shock or burns.
3.3.6. WARNING Fuel and its vapours are extremely flammable and explosive.
3.3.7. WARNING Fire or explosion can cause severe burns or death.
3.3.7.1. When Adding or Draining Fuel
HYW2500P_HYW3000P_HYW3100P_HYW3100P2_HYW4000P Combined user manual Rev 7.pdf 7 16/12/2015 11:43:50

Page 8
Rev 7
3.3.7.1.1. Turn pressure washer OFF and let it cool at least 2 minutes
before removing fuel cap. Loosen cap slowly to release pressure in
tank.
3.3.7.1.2. Fill or drain fuel tank outdoors.
3.3.7.1.3. DO NOT overfill tank. Allow space for fuel expansion (25mm
from top).
3.3.7.1.4. If fuel spills, wait until it evaporates before starting engine.
3.3.7.1.5. Keep fuel away from sparks, open flames, pilot lights, heat,
and other ignition sources.
3.3.7.1.6. DO NOT light a cigarette or smoke.
3.3.7.2. When Starting Equipment
3.3.7.2.1. Ensure spark plug, exhaust, fuel cap, and air cleaner are in
place.
3.3.7.2.2. DO NOT crank engine with spark plug removed.
3.3.7.3. When Operating Equipment
3.3.7.3.1. DO NOT tip engine or equipment at angle which causes fuel to
spill.
3.3.7.3.2. DO NOT spray flammable liquids.
3.3.7.4. When Transporting or Repairing Equipment
3.3.7.4.1. Transport/repair with fuel tank EMPTY or with fuel shutoff
valve OFF.
3.3.7.4.2. Disconnect spark plug wire.
3.3.7.5. When Storing Fuel or Equipment with Fuel in Tank
3.3.7.5.1. Store away from furnaces, stoves, water heaters, clothes
dryers, or other appliances that have pilot light or other ignition
source because they can ignite fuel vapours.
3.3.8. WARNING Engine exhaust fumes contain carbon monoxide, an odourless,
colourless, poison gas. Breathing carbon monoxide can cause headache,
fatigue, dizziness, vomiting, confusion, seizures, nausea, fainting or death.
Some chemicals or detergents may be harmful if inhaled or ingested, causing
severe nausea, fainting, or poisoning.
3.3.8.1. ONLY operate pressure washer outdoors.
3.3.8.2. Do not allow exhaust gas from entering a confined area through
windows, doors, ventilation intakes or other openings.
3.3.8.3. DO NOT start or run engine indoors or in an enclosed area, even if
windows and doors are open.
3.3.8.4. Use a respirator or mask whenever there is a chance that vapours
may be inhaled.
3.3.8.5. Read all instructions with the mask so you are certain the mask will
provide the necessary protection against inhaling harmful vapours.
HYW2500P_HYW3000P_HYW3100P_HYW3100P2_HYW4000P Combined user manual Rev 7.pdf 8 16/12/2015 11:43:50

Page 9
Rev 7
3.3.9. WARNING Starter cord kickback (rapid retraction) can result in bodily injury.
Kickback will pull hand and arm toward engine faster than you can let go.
Broken bones, fractures, bruises, or sprains could result.
3.3.9.1. NEVER pull starter cord without first releasing spray gun pressure.
3.3.9.2. When starting engine, pull cord slowly until resistance is felt and then
pull rapidly to avoid kickback.
3.3.9.3. After each starting attempt, where engine fails to run, always point
spray gun in safe direction and squeeze spray gun trigger to release high
pressure.
3.3.9.4. Firmly grasp spray gun with both hands when using high pressure
spray to avoid injury when spray gun kicks back.
3.3.10. WARNING Use of pressure washer can create puddles and slippery surfaces.
3.3.11. WARNING Kickback from spray gun can cause you to fall.
3.3.11.1. Operate pressure washer from a stable surface.
3.3.11.2. The cleaning area should have adequate slopes and drainage to
reduce the possibility of a fall due to slippery surfaces.
3.3.11.3. Be extremely careful if you must use the pressure washer from
scaffolding or any other similar location.
3.3.11.4. Firmly grasp spray gun with both hands when using high pressure
spray to avoid injury when spray gun kicks back.
3.3.12. WARNING Contact with exhaust area can result in serious burns.
3.3.13. WARNING Exhaust heat/gases can ignite combustibles, structures or damage
fuel tank causing a fire.
3.3.13.1. DO NOT touch hot parts and AVOID hot exhaust gases.
3.3.13.2. Allow equipment to cool before touching.
HYW2500P_HYW3000P_HYW3100P_HYW3100P2_HYW4000P Combined user manual Rev 7.pdf 9 16/12/2015 11:43:50

Page 10
Rev 7
3.3.13.3. Keep at least 5 feet (1.5 m) of clearance on all sides of pressure
washer including overhead.
3.3.14. WARNING Risk of eye injury. Spray can splash back or propel objects.
3.3.14.1. Always wear safety goggles when using this equipment or in vicinity of
where equipment is in use.
3.3.14.2. Before starting the pressure washer, be sure you are wearing
adequate safety goggles.
3.3.14.3. NEVER substitute safety glasses for safety goggles.
3.3.15. WARNING The high pressure stream of water that this equipment produces
can cut through skin and its underlying tissues, leading to serious injury and
possible amputation. Spray gun traps high water pressure, even when engine is
stopped and water is disconnected, which can cause injury.
3.3.15.1. DO NOT allow CHILDREN to operate pressure washer.
3.3.15.2. NEVER repair high pressure hose. Replace it.
3.3.15.3. NEVER repair leaking connections with sealant of any kind. Replace O-
ring or seal.
3.3.15.4. NEVER connect high pressure hose to nozzle extension.
3.3.15.5. Keep high pressure hose connected to pump and spray gun while
system is pressurised.
3.3.15.6. ALWAYS point spray gun in safe direction and squeeze spray gun
trigger, to release high pressure, every time you stop engine.
3.3.15.7. NEVER aim spray gun at people, animals, or plants.
3.3.15.8. DO NOT secure spray gun in open position.
3.3.15.9. DO NOT leave spray gun unattended while machine is running.
3.3.15.10. NEVER use a spray gun which does not have a trigger lock or trigger
guard in place and in working order.
3.3.15.11. Always be certain spray gun, nozzles and accessories are correctly
attached.
3.3.16. WARNING Starter and other rotating parts can entangle hands, hair, clothing,
or accessories.
3.3.16.1. NEVER operate pressure washer without protective housing or covers.
3.3.16.2. DO NOT wear loose clothing, jewellery or anything that may be caught
in the starter or other rotating parts.
HYW2500P_HYW3000P_HYW3100P_HYW3100P2_HYW4000P Combined user manual Rev 7.pdf 10 16/12/2015 11:43:50

Page 11
Rev 7
3.3.16.3. Tie up long hair and remove jewellery.
3.3.17. WARNING Unintentional sparking can result in fire or electric shock.
3.3.17.1. When Adjusting or Making Repairs to Your Pressure Washer
3.3.17.1.1. Disconnect the spark plug cap from the spark plug and place it
where it cannot contact spark plug.
3.3.17.2. When Testing for Engine Spark
3.3.17.2.1. Use approved spark plug tester.
3.3.17.2.2. DO NOT check for spark with spark plug removed.
3.3.18. NOTICE High pressure spray may damage fragile items including glass.
3.3.18.1. DO NOT point spray gun at glass when using red 0° spray tip.
3.3.18.2. NEVER aim spray gun at plants.
3.3.19. NOTICE Improper treatment of pressure washer can damage it and shorten
its life.
3.3.19.1. If you have questions about intended use, ask your dealer or contact
nearest authorised dealer.
3.3.19.2. NEVER operate units with broken or missing parts, or without
protective housing or covers.
3.3.19.3. DO NOT by-pass any safety device on this machine.
3.3.19.4. DO NOT tamper with governed speed.
3.3.19.5. DO NOT operate pressure washer above rated pressure.
3.3.19.6. DO NOT modify pressure washer in any way.
3.3.19.7. Before starting pressure washer in cold weather, check all parts of the
equipment to be sure ice has not formed there.
3.3.19.8. NEVER move machine by pulling on hoses. Use handle provided on
unit.
3.3.19.9. Check fuel system for leaks or signs of deterioration, such as chafed or
spongy hose, loose or missing clamps, or damaged tank or cap. Correct all
defects before operating pressure washer.
HYW2500P_HYW3000P_HYW3100P_HYW3100P2_HYW4000P Combined user manual Rev 7.pdf 11 16/12/2015 11:43:50

Page 12
Rev 7
4. PRESSURE WASHER COMPONENTS
Read this operating manual and safety rules before operating your pressure washer.
1. Nozzles
Detergent, 0°,
15°, 40° & Turbo
Nozzle: for high
pressure cleaning
applications.
2. High Pressure
Hose Connect
one end to water
pump and the
other end to
spray gun.
3. Pressure
Control Knob
Varies pressure
of high pressure
spray.
4. Water Inlet
Connection for
garden hose.
5. High Pressure
Outlet
Connection for
high pressure
hose.
6. Pump
Develops high
pressure.
7. Oil Level
Indicator Level
should be at
halfway
8. Choke Lever
Prepares a cold
engine for
starting.
9. Fuel Valve
used to turn fuel
supply on and off
to engine.
10. Recoil Starter
Used for starting
the engine
manually.
11. Throttle Lever
Sets engine in starting
mode for pull starter.
12. Engine Switch Set
switch to “On” for pull
starting. Set switch to
“Off” to stop a
running engine.
13. Air Filter Protects
engine by filtering
dust and debris out of
air intake.
14. Fuel Tank Fill tank
with regular unleaded
fuel. Always leave
room for fuel
expansion (25mm
from top)
15.Spray Gun Extension with Quick Connect Nozzles Controls the application of water onto
cleaning surface with trigger device. Includes trigger lock. Allows you to switch between five
different nozzles.
HYW2500P_HYW3000P_HYW3100P_HYW3100P2_HYW4000P Combined user manual Rev 7.pdf 12 16/12/2015 11:43:50

Page 13
Rev 7
5. ASSEMBLY
5.1. Your pressure washer requires some assembly and is ready for use after it has been
properly filled with both the recommended oil and fuel.
5.2. If you have any problems with the assembly of your pressure washer, please call the
help line. If calling for assistance, please have the model and serial number from the
data tag available.
5.3. Unpack the Pressure Washer
5.3.1. Remove the parts bag, accessories, and inserts included with pressure
washer.
5.3.2. Remove machine from box.
5.3.3. Ensure you have all included items prior to assembly.
5.4. Attach Handle
5.4.1. Place handle (A) onto handle supports (B) connected to main unit. Make sure
holes (C) in handle align with holes on handle supports.
5.4.2.
5.5. NOTE It may be necessary to move the handle supports from side to side in order to
align the handle so it will slide over the handle supports.
5.6. Insert carriage bolts through holes from outside of unit and attach a plastic knob
from inside of unit. Tighten by hand.
5.7. Insert multi coloured quick connect spray tips and other supplied accessories in
spaces provided on handle.
HYW2500P_HYW3000P_HYW3100P_HYW3100P2_HYW4000P Combined user manual Rev 7.pdf 13 16/12/2015 11:43:50

Page 14
Rev 7
6. PRE OPERATION CHECK LIST
6.1. Follow the Checklist Below Prior to Using the Machine Each Time
6.1.1. Check to ensure the engine oil is at the proper level.
6.1.2. Use SAE 15W40 Oil
6.1.3. Check the 2 handle knobs to ensure they are tight and will not vibrate loose.
6.1.4. Add fuel to the petrol tank - Regular Unleaded Petrol
6.1.5. Connect and tighten the garden hose to the garden hose attachment.
NOTE Water must be turned on prior to starting the washer, pull the spray trigger to ensure
water is moving the through the lines and out the nozzle without any leaks before starting
the unit.
6.1.6. Review the safety guidelines in the manual prior to starting the unit.
6.1.7. If you have any issues operating the pressure washer, call after sales on
01646 687880.
6.2. WARNING Always check the level of the engine and pump oil prior to starting the
washer.
6.2.1. Failure to do so could cause the engine and pump to seize if the oil is low or
empty.
6.3. WARNING Connect hose and water supply to pump before starting. DO NOT start
your pressure washer without the water supply turned on.
6.3.1. Failure to do so will result in damaging the pump from overheating and void
the warranty.
7. STARTING YOUR WASHER
7.1. To start your pressure washer for the first time, follow these instructions step-by-
step. This starting information also applies if you have let the pressure washer sit
idle for at least a day.
7.1.1. Place pressure washer near an outside water source capable of supplying
water at a flow rate greater than 14.4 litres per minute and no less than 20 PSI
at pressure washer end of garden hose. DO NOT siphon supply water.
7.1.2. Make sure unit is in a level position.
7.1.3. Connect garden hose to water inlet on pressure washer pump.
7.2. NOTE DO NOT run the pump without the water supply connected and turned on.
7.3. Attach wand extension to spray gun and tighten by hand.
HYW2500P_HYW3000P_HYW3100P_HYW3100P2_HYW4000P Combined user manual Rev 7.pdf 14 16/12/2015 11:43:50

Page 15
Rev 7
7.4. Choose desired nozzle, pull back nozzle extension collar, insert nozzle and release
collar. Tug on nozzle to make sure it is securely in place. See Nozzle Selection
Section.
7.5. Uncoil high pressure hose and attach quick connect end of hose to base of spray
gun. Pull down on collar of quick connect, slide onto spray gun and let go of collar.
Tug on hose to be sure of tight connection. Some models may use a threaded hose
connector.
7.6. WARNING The high pressure stream of water that this equipment produces can cut
through skin and its underlying tissues, leading to serious injury and possible
amputation.
7.6.1. NEVER connect high pressure hose to nozzle extension.
7.6.2. Keep high pressure hose connected to pump and spray gun while system is
pressurized.
7.6.3. Always be certain spray gun, nozzles and accessories are correctly attached.
7.7. attach other end of high pressure hose to high pressure outlet (A) on pump. Pull
down on collar of quick connect, slide onto pump and let go of collar. Pull on hose
to be sure of tight connection. *Some models may use a threaded hose connector.
7.8. NOTE Pump Uses SAE 15W 40 Oil.
7.9. Turn Water Supply on, point gun in a safe direction and squeeze the trigger to purge
the pump of air and debris. Do this for at least 30 seconds.
7.10. Take a look at all connections to make sure there are no leaks or loose
connections.
HYW2500P_HYW3000P_HYW3100P_HYW3100P2_HYW4000P Combined user manual Rev 7.pdf 15 16/12/2015 11:43:51

Page 16
Rev 7
7.11. IMPORTANT If drawing water from a barrel, it is advisable to have a gravity-
fed supply. Use ONLY cold water (less than 38°C/100°F).
7.12. Connect the garden hose to the water inlet. Tighten by hand.
7.13. To start the machine, locate the engine switch on the side of the engine, and
switch it to the ON position. (see component chart to locate switch) Check to ensure
fuel valve is in the ON position and if starting cold apply the choke.
7.14. Always release water pressure by squeezing trigger gun.
7.15. Pull recoil cord slowly until resistance is felt and then pull rapidly to avoid
kickback. Make sure to position yourself in a balanced position. DO NOT place hand
on engine exhaust for balance, this will result in severe burns.
7.16. WARNING Running engine gives off carbon monoxide, an odourless,
colourless, poison gas. Breathing carbon monoxide can cause headache, fatigue,
dizziness, vomiting, confusion, seizures, nausea, fainting or death.
7.16.1. Operate pressure washer ONLY outdoors.
7.16.2. Keep exhaust gas from entering a confined area through windows, doors,
ventilation intakes, or other openings.
7.16.3. DO NOT start or run engine indoors or in an enclosed area, even if windows
and doors are open.
7.17. IMPORTANT Before starting the pressure washer, be sure you are wearing
adequate safety goggles.
7.18. WARNING Risk of eye injury. Spray can splash back or propel objects.
7.18.1. Always wear safety goggles when using this equipment or in vicinity of where
equipment is in use.
7.18.2. Before starting the pressure washer, be sure you are wearing adequate
safety goggles.
7.18.3. NEVER substitute safety glasses for safety goggles.
7.19. WARNING Starter cord kickback (rapid retraction) can result in bodily injury.
Kickback will pull hand and arm toward engine faster than you can let go. Broken
bones, fractures, bruises, or sprains could result.
7.19.1. NEVER pull starter cord without first relieving spray gun pressure.
7.19.2. When starting engine, pull cord slowly until resistance is felt and then pull
rapidly to avoid kickback.
7.19.3. After each starting attempt, where engine fails to run, always point spray gun
in safe direction and squeeze spray gun trigger to release high pressure.
7.19.4. Firmly grasp spray gun with both hands when using high pressure spray to
avoid injury when spray gun kicks back.
HYW2500P_HYW3000P_HYW3100P_HYW3100P2_HYW4000P Combined user manual Rev 7.pdf 16 16/12/2015 11:43:51

Page 17
Rev 7
7.20. WARNING The high pressure stream of water that this equipment produces
can cut through skin and its underlying tissues, leading to serious injury and possible
amputation. Spray gun traps high water pressure, even when engine is stopped and
water is disconnected, which can cause injury.
7.20.1. DO NOT allow CHILDREN to operate pressure washer.
7.20.2. NEVER repair high pressure hose. Replace it.
7.20.3. NEVER repair leaking connections with sealant of any kind. Replace O-ring or
seal.
7.20.4. NEVER connect high pressure hose to nozzle extension.
7.20.5. Keep high pressure hose connected to pump and spray gun while system is
pressurized.
7.20.6. ALWAYS point spray gun in safe direction and squeeze spray gun trigger, to
release high pressure, every time you stop engine.
7.20.7. NEVER aim spray gun at people, animals, or plants.
7.20.8. DO NOT secure spray gun in open position.
7.20.9. DO NOT leave spray gun unattended while machine is running.
7.20.10. NEVER use a spray gun which does not have a trigger lock or trigger
guard in place and in working order.
7.20.11. ALWAYS be certain spray gun, nozzles and accessories are correctly
attached.
7.21. WARNING Contact with exhaust area can result in serious burns.
7.22. WARNING Exhaust heat/gases can ignite combustibles, structures or damage
fuel tank causing a fire.
7.22.1. DO NOT touch hot parts and AVOID hot exhaust gases.
7.22.2. Allow equipment to cool before touching.
7.22.3. Keep at least1.5m (5 feet) of clearance on all sides of pressure washer
including overhead.
8. SHUTTING DOWN YOUR WASHER
8.1. How to Shut Down Your Pressure Washer
8.1.1. Release spray gun trigger and let engine idle down.
8.1.2. Turn the engine switch to the OFF position.
8.1.3. ALWAYS point spray gun in a safe direction, squeeze spray gun trigger to
release retained high water pressure.
8.2. IMPORTANT Spray gun traps high water pressure, even when engine is stopped and
water is disconnected. Couplings will not release if under pressure.
HYW2500P_HYW3000P_HYW3100P_HYW3100P2_HYW4000P Combined user manual Rev 7.pdf 17 16/12/2015 11:43:51

Page 18
Rev 7
8.3. WARNING The high pressure stream of water that this equipment produces can cut
through skin and its underlying tissues, leading to serious injury and possible
amputation. Spray gun traps high water pressure, even when engine is stopped and
water is disconnected, which can cause injury.
8.3.1. Keep high pressure hose connected to pump and spray gun while system is
pressurized.
8.3.2. ALWAYS point spray gun in safe direction and squeeze spray gun trigger, to
release high pressure, every time you stop engine.
9. QUICK RELEASE NOZZLES
9.1. The quick–release on the lance allows you to switch between four different quick-
release nozzles. The nozzles can be changed while pressure washer is running once
spray gun trigger safety lock is engaged. The different nozzles vary the spray pattern
as shown below.
9.2. WARNING The high pressure stream of water that this equipment produces can cut
through skin and its underlying tissues, leading to serious injury and possible
amputation.
9.2.1. NEVER change nozzles without the trigger safety lock being engaged on the
spray gun.
9.2.2. DO NOT twist nozzles whilst spraying.
9.3. Follow these instructions to change the nozzles:
9.3.1. Pull back collar on quick–connect and pull current nozzle off. Store nozzles in
holder provided on the handle. Storing nozzles in the designated holder will
help prevent debris clogging the tip.
9.3.2. Select desired nozzle:
9.3.2.1. For gentle rinse, select white 40° nozzle.
9.3.2.2. To scour surface, select yellow 15° or red 0° nozzle.
9.3.2.3. To apply detergent, select black nozzle.
HYW2500P_HYW3000P_HYW3100P_HYW3100P2_HYW4000P Combined user manual Rev 7.pdf 18 16/12/2015 11:43:51

Page 19
Rev 7
9.3.2.4. Pull back on collar, insert new nozzle and release collar. Tug on nozzle
to make sure it is securely in place.
9.4. Usage tips.
9.4.1. For most effective cleaning, keep nozzle from 8 to 24 inches away from
cleaning surface.
9.4.2. If you get nozzle too close, especially using a high pressure nozzle, you may
damage surface being cleaned.
9.5. To apply detergent, follow these steps:
9.5.1. Fit black soap nozzle.
9.5.2. Prepare detergent solution as required by job.
9.5.3. Place small filter end of detergent siphoning tube into detergent container.
9.5.4. NOTE Make sure the filter is fully submerged in detergent while applying
detergent.
9.5.5. NOTE This washer will only draw soap with the black soaper nozzle. The
White, Red, and Yellow nozzle will not draw soap.
9.6. Make sure black nozzle is installed.
9.7. Make sure garden hose is connected to water inlet. Check that high pressure hose is
connected to spray gun and pump. Turn on water.
9.8. NOTICE You must attach all hoses before you start the engine.
9.8.1. Starting the engine without all the hoses connected and without the water
turned ON will damage the pump.
9.8.2. Damage to equipment resulting from failure to follow this instruction will
void the warranty.
9.9. IMPORTANT You must flush the detergent siphoning system after each use by
placing the filter into a bucket of clean water, then run the pressure washer at low
pressure for 1-2 minutes.
9.10. CAUTION Chemicals can cause bodily injury and/or property damage.
9.10.1. NEVER use caustic liquid with pressure washer.
9.10.2. Use ONLY pressure washer safe detergent/soaps. Follow all manufacturer’s
instructions.
HYW2500P_HYW3000P_HYW3100P_HYW3100P2_HYW4000P Combined user manual Rev 7.pdf 19 16/12/2015 11:43:51

Page 20
Rev 7
10. TROUBLESHOOTING
10.1. If you are experiencing a problem that is not listed in this chart, or have
checked all the possible cause listed and you are still experiencing the problem,
contact Aftersales on 01646 687880.
10.2. Petrol engine trouble shooting.
Problem
Cause
Correction
Unit has following problems:
Failure to produce pressure, erratic
pressure, chattering, loss
of pressure, low water volume.
1. Low pressure spray tip installed.
2. Water inlet is blocked.
3. Inadequate water supply.
4. Inlet hose is kinked or leaking.
5. Clogged inlet hose screen.
6. Water supply is over 100°F (38°C).
7. High pressure hose is blocked
or leaks.
8. Spray gun leaks.
9. Spray tip is obstructed.
10. Pump is faulty.
1. Replace with high pressure spraytip.
2. Clear inlet.
3. Provide adequate water flow.
4. Straighten inlet hose, patch leak.
5. Check and clean inlet hose screen.
6. Provide cooler water supply.
7. Clear blocks in outlet hose.
8. Replace spray gun.
9. Clean spray tip.
10. Contact local service agent.
Detergent fails to mix with spray.
1. Detergent siphoning tube is not
submerged.
2. Detergent siphoning tube/ filter is
clogged or cracked.
3. High pressure spray tip installed.
1. Insert detergent siphoning tube into
detergent.
2. Clean or replace filter/ detergent
siphoning tube.
3. Replace with low pressure spray tip.
Engine lacks power.
1. Dirtyairfilter.
1. Replace air filter.
Engine will not start
1. Throttle lever on/off switch in OFF
position
2. No fuel in engine
3. Worn fouled or dirty spark plug
4. Pressure build up in pump
1. Turn throttle lever to ON position
2. Fill fuel tank or turn on fuel supply
3. Replace with factory recommended
spark plug
4. Squeezetrigger onspray lance
Units with Oil alert
1. Engine not level or Engine oil level
too low
1. Place engine on level surface or
fill crankcases with SAE 15W40
oil.
Engine runs well at no load but “bogs”
down under full load
1. Engine speed is too slow
1. Adjust Throttle Lever back to full
throttle.
Engine will not start; or starts and runs
rough
1. Low oil level
2. Dirty air cleaner
3. Out of petrol
4. Stale petrol
5. Spark plug wire not connected to
spark plug
6. Badsparkplug
7. Waterin petrol
8. Over choking
1. Fill crankcase to proper level
2. Clean or replace air cleaner
3. Fill fuel tank
4. Drain gas tank, fill with fresh fuel
5. Connect wire to spark plug
6. Replace spark plug
7. Drain gas tank, fill with fresh fuel
8. Open choke fully and crank engine
Engine shuts down during operation
1. Out of petrol
2. Low oil level
1. Fill fuel tank
2. Fill crankcase with oil, to proper
Engine lacks power
1. Dirtyair filter
1. Replace air filter
Engine “putts” or falters
1. Choke is opened too soon
1. Move choke to halfway position
until engine runs smoothly
* All engine servicing to be taken to
manufacturer’sauthorized service outlet
HYW2500P_HYW3000P_HYW3100P_HYW3100P2_HYW4000P Combined user manual Rev 7.pdf 20 16/12/2015 11:43:51