I-Tech SNK117 Series User manual

User
Manual
1U Rackmount LCD Keyboard Drawer
SNK117/ 119 Series
17 / 19 LCD
Optional KVM
8, 16 Ports USB Single Console

Rev. : 1.0 P.1
1. Table Of Content
1. Table of Content P.1
2. Read Before Installation P.2
3. Introduction P.3
4. Features P.3
5. Package Contents P.4
6. Optional Accessories P.5
7. Peripheral Products P.5
8. Important Safeguards P.6
9. Structure Diagram P.7
10.Dimension Diagram
SNK117-8/1601 P.8
SNK119-8/1601 P.9
11. LCD Session
LCD Membrane Diagram P.11
LCD OSD Control
Main Menu P.11
Sub Menu P.12-13
Resolution Settings
For Windows P.14
12.KVM Session
Front View P.16
Rear View P.17
Installation Steps P.18
Cascading P.19
13. Start Up P.20
HotKey Command P.20
HotKey Command Operation P.21-22
KVM OSD Operation
Main Controls P.23
Sub Controls P.24-29
14.Keyboard & Key Pad Layout P.30
15.FAQ P.31
16.Technical Specification P.32-33

Technical Notes
For Windows 98/98 SE systems
HID (Human Interface Device) driver must be installed prior to using
the USB KVM switch. To install the HID driver, first connect a USB
keyboard and mice directly to computer (before installing KVM switch)
then follow the Windows installation instructions, this will install the HID
device driver and allow the use of the KVM switch.
If a mouse recognition error is displayed during system boot:
Windows did not detect a mouse attached to the computer.You can
safely attach a serial mouse now. To attach a mouse to a PS/2 mouse
port, you must first turn the computer off”
a) Press the Tab key once to select the check box.
b) Press the Space bar once which will place a check in the box
Do not show this message again”
c) Press the Enter key once and Windows will continue to boot and
will then recognize the mouse.
Operating System Compatibility
Any USB-enabled operating system such as Solaris®, Windows®98,
Windows®98SE, Windows®2000, Windows®XP or higher.
Windows®95 are not recommended because of immature USB
support.
Introduction
Note : Failure to do so may result in Windows not being able to detect
keyboard and mouse.
Rev. : 1.0 P.2
2. Read Before Installation
* All brand names, logo registered trademarks are properties of their respective owners.
S117 / S119 User Manual

Rev. : 1.0 P.3
S Solutions is total compatible with Solaris. The LCD screen support SUN
native 1152 x 900 & standard resolutions. SUN-compatible keyboard incor-
porates SUN system administration commands keys.
It is a combination of keyboard, mouse and monitor into a drawer, with features
such as flip-up design, adjustable brackets, built in LCD OSD to provide ef-
fective assistant for an administrator to control SUN/ PC system.
3. Introduction
4. Features
1U 17”or 19”TFT LCD screen
Standard color purple light grey.
The screen direct support most SUN native resolution, including 1152 x
900 @ 66 or 76Hz
Hot-key for SUN-Solaris system administration commands including
Help, Stop, Cut, Paste, Compose etc.
Compatible with SUN, Apple, IBM, DELL, HP and USB server
104-keys SUN-compatible keyboard w/ 3 button trackball supports additional
manipulations such as panning and scrolling.
Fits all current SUN racks, Fits 24”to 36”rack depths via adjustable
mounting brackets
12V, 24V, 48V DC power supply options
Built-in KVM switch function for easy controlling and monitoring up to 16
residing servers/ platforms
Support eight characters password protection and search PC server
name
Auto scan mode for monitoring PCs and flexible scan time from 5~99
seconds
Hot Pluggable—Add or remove computers without powering down the
switch
Disclaimer
This information is subject to change without notice. The producer of this manual accepts no
responsibility for damage or claims, resulting from misuse or misinterpretation
S117 / S119 User Manual

Rev. : 1.0 P.4
5. Package Contents
Before Unpacking
It is very important to locate the LCD Keyboard Drawer in a suitable environment.
The surface for placing and fixing the LCD Keyboard Drawer should be stable and level
or mounted into a suitable cabinet.
Make sure the place has good ventilation, is out of direct sunlight, away from sources of
excessive dust, dirt, heat, water, moisture and vibration.
Convenience for connecting the LCD Keyboard Drawer to the related facilities should be
well considers too.
Unpacking
The LCD Keyboard Drawer comes with the standard parts shown as above. Check and make
sure they are included and in good condition. If anything is missing, or damage, contact the
supplier immediately.
LCD Monitor Drawer (optional USB KVM Switch) 1 Piece
User Manual 1 Piece
DC Power Adapter 1 Piece
Power Cord 1 Piece
Mounting Bracket 1 Pair
Fasteners 4 Pieces
CB-6 2-in-1 KVM cable (without KVM) 1 Piece
CB-6 2-in-1 KVM cable (with KVM) 8 Pieces
S117 / S119 User Manual

Rev. : 1.0 P.5
6. Optional Accessories
7. Peripheral Products
CV-S801 8-Port USB KVM switch
CV-S1601 16-Port USB KVM switch
CV-S1602 16-Port USB two consoles KVM switch
CV-S101 CAT.5 USB KVM extender
CB-6 / 10 / 15 6ft / 10ft / 15ft USB 2-in-1 cable
6ft USB Cascade cable
Video Input
12V / 24V / 48V DC Power Supply
KVM Cable
Cascade Cable
Others
S117 / S119 User Manual

Rev. : 1.0 P.6
Please read all of these instructions carefully before you use the device.
Save this manual for future reference.
Unplug the LCD Keyboard Drawer from the power outlet before cleaning.
Do not spray liquid cleaners or aerosol directly on the device. Wet a cloth with a
neutral detergent (e.g. clean water) and squeeze it tight, then clean the screen
slightly with it.
Do not expose the LCD Keyboard Drawer directly to rain, water, moisture or
sunlight.
Avoid pressure on the LCD screen to prevent permanent damage to the display.
Do not attempt to service the device yourself. Improper operation may void your
warranty. Refer all servicing to qualified service personnel.
Safe storage environment of the LCD Keyboard Drawer is ranging between –20oC
and 60oC. Permanent damage could occur if the LCD Keyboard Drawer is stored
outside the safe range.
Unplug the LCD Keyboard Drawer immediately and call qualified service
personnel under the following conditions:
1. If the monitor has been exposed to rain, liquid or water.
2. If the monitor has been dropped or the casing has been damaged.
What the warranty does not cover
1. Any product, on which the serial number has been defaced, modified or
removed.
2. Damage, deterioration or malfunction resulting from:
a) Accident, misuse, neglect, fire, water, lightning, or other acts of nature,
unauthorized product modification, or failure to follow instructions supplied
with the product.
b) Repair or attempted repair by anyone not authorized by us.
c) Any damage of the product due to shipment.
d) Removal or installation of the product.
e) Causes external to the product, such as electric power fluctuation or failure.
f) Use of supplies or parts not meeting our specifications.
g) Normal wear and tear.
h) Any other causes which does not relate to a product defect.
3. Removal, installation, and set-up service charges.
8. Important Safeguards
S117 / S119 User Manual

Rev. : 1.0 P.7
9. Structure Diagram
1. USB SUN compatible keyboard
2. 3 Buttons trackball mouse
3. SUN keys
4. Aluminium front panel
5. Class A active matrix TFT LCD panel
6. LCD membrane
7. Ball bearing telescopic slides with stopper
8. Adjustable mounting bracket
9. USB KVM switch ( Optional )


 



S117 / S119 User Manual

Rev. : 1.0 P.8
SNK117- 8/1601 1U 17! LCD Keyboard Drawer with USB KVM
10. Dimension Diagram
17" LCD

Rev. : 1.0 P.10
LCD
Session
S117 / S119 User Manual

Rev. : 1.0 P.11
LCD Membrane Diagram
Left Right Exit
Menu/SelectionPower
MAIN MENU
BRIGHT/CONTRAST
AUTO ADJUST
PHASE/CLOCK
H/V POSITION
MISC
RESET
Main Menu
Bright / Contrast
To enter into the Bright, Black level & Contrast sub-menu
Auto Adjust
To perform automatic optimisations of all functions
An Adjusting”message is displayed during the process
Phase / Clock
To enter into the phase & clock sub menu
H/V Position
To enter into the H/VPosition sub-menu
MISC
To enter into the MISC sub-menu
Reset
Reset to the default factory settings
11. LCD Session
S117 / S119 User Manual

Rev. : 1.0 P.12
Bright / Contrast
1. Brightness
To perform brightness adjustment of the input RGB signal
Use the Left & Right button to adjust and button to Brightness”
2. Contrast
To adjust the contrast level of the input signal
Use the Left & Right button to adjust and button to Contrast”
Phase / Clock
1. Phase
To adjust input video sampling clock’s phase
Use the Left & Right button to adjust and button to Phase”
2. Clock
To adjust input video sampling clock
Use the Left & Right button to adjust and button to Clock”
H/V Position
1. H.Position
To adjust the horizontal size of the frame
Use the Left & Right button to adjust and button to H.position”.
2. V.Position
To adjust the vertical position of the frame
Use the Left & Right button to adjust and button to V.position”.
11. LCD Session
S117 / S119 User Manual

Rev. : 1.0 P.13
MISC
1. Information
The first header row shows the current resolution setup
The second header row shows the horizontal frequency of the current
input signal
The third header row shows the vertical frequency of the current input
signal
2. OSD Timer
To modify the duration of the OSD time-out
3. Color
a) 5500K
Select Colour Temp at 5500K
b) 6500K
Select Colour Temp at 6500K
c) 9500K
Select Colour Temp at 9500K
d) User
Change Colour Temp by manual
4. Language
To select the language of OSD menu 7 Languages :
(1) English
(2) Japanese (!"#)
(3) Chinese ($%)
(4) German
(5) Francais
(6) Espanol
(7) Italiano
11. LCD Session
S117 / S119 User Manual

Rev. : 1.0 P.14
Resolution Settings
For Microsoft Windows
Step 1 –Press right click on the desktop
Step 2 –Choose Properties”
Step 3 –Change the Screen Resolution”
Step 4 –Change the Screen refresh rate”
11. LCD Session
S117 / S119 User Manual

Rev. : 1.0 P.15
KVM
Session
S117 / S119 User Manual

Rev. : 1.0 P.16
Front View
Channel Select Button
Selected Channel Bank Button
Bank No.
Shift ButtonOnline Channel
LED Indication
Selected Channel - Displayed channel on monitor & red in LED.
Channel select button - Press to select channel from 1 –8.
Shift button - Press & Hold follow with a channel button
to select channel from 9 –16.
Online Channel - Green LED state the PC has connected
and power on.
Bank no. - Display the Bank no. from 1 –8.
Bank button - Select the bank from 1 –8 (for cascade only).
12. KVM Session
S117 / S119 User Manual

Rev. : 1.0 P.17
12. KVM Session
Rear View
Cascade
Port
Channel
Port
DC
Power
RKP1XX-S801
RKP1XX-S1601
DC Power -connect to external 12V DC power adapter.
Cascade Port -
connect to additional KVM switch for channel
expansion.
Console Port - connect to monitor, PS/2 keyboard & mouse.
Channel Port - connect to PC computer with CB-6 2-in-1 KVM cable.
S117 / S119 User Manual

Rev. : 1.0 P.18
12. KVM Session
Installation Steps
Before installation, please make sure all computers are turned on and its
operating system are running properly with keyboard and mouse.
1. Connect the 2-in-1KVM cable to the one of your server.
USB Type A Male connector to the USB Port
HDDB 15-pin Male connector to the VGA Port
2. Plug the power adapter included to the switch.
3. Connect the another end of the 2-in-1 cable to the USB KVM switch
4. Reset USB KVM Switch by membrane
DC
Power
PC I/O windows diagram
To VGA port
S117 / S119 User Manual