I-Tech ADTR-IP66 Series User manual

SxxxxADTR-IP66 Series
Quick Reference
i-Tech Company LLC
TOLL FREE: [phone] • EMAIL: [e-mail] • WEB: www.iTechLCD.com

1. Feature
SxxxxADTR-IP66 solid aluminum die-cast casing body maintains a strong,
compact look and utilizes innovative mechanism design to prevent dust, oil
and water from harsh environments. SxxxxADTR-IP66 fits perfectly to
hospitality, retail, finance and banking, travel and transportation, and self-
service kiosk.
Highlights:
■Whole Unit IP66 Certification
■Aluminum Casing
■Fanless design
■Removable Hard Disk
■Wireless LAN
■VESA Mount or Stand
■Sub-Nano Coating
Applications:
■Hospitality
■Retail
■Finance & Banking
■Travel & Transportation
■Self-service Kiosk
Note: Optional devices such as VESA standard mounting bracket or arm, Rotation
disk, Customer Display, Magnetic Card Reader, Smart Card Reader, I-Button,
Finger Print, RFID, and other I/O devices are available for optional choice.
1

2. Unpacking
The following items are included when you purchase the SxxxxADTR-
IP6. If any items are damaged or missing, please contact your dealer for
assistance.
Quick Reference
Antenna
(Optional Part)
3. Configuration
Front and Rear View
Push ON Switch-
Foot(5x) XT USB
2
VFD Interface Cover
Antenna X^HDD
Cover

Bottom View – I/O Connector Location
Chassis Inner View
3

I/O Connector Location (VESA MOUNT)
COM6
COM5
COM4
COM3
Audio Out
CF Card
4. Power On
Red
Blue
- AC Input OK
- Power On Mode
4
PRINTER or VGA
EXT USB
PS2 K/B
LAN
EXT USB
Turn on the unit by pressing “Push ON Switch” located under iTech
logo indicator at front of the LCD. Turn off the unit manually by
pressing and holding the switch for 3 seconds. When connected to an
AC power, the Power Mode LED will illuminate automatically. The
unit’s mode can be determined by the Power On Mode LED color.
Indicator modes as follows:

5. HDD Replacement
To remove HDD, use a screwdriver to loosen the screws on left side
of the panel.
Caution :
A. Hard Disk must be screwed into HDD Cover.
B. To install or to withdraw HDD, power must be switched off.
5

6. LCD Angle Adjust
6.1 In order to accommodate various operating preferences and
lighting conditions. SxxxxADTR-IP66 is equipped with a manual
tilt adjustment mechanism. The Adjustment button is located
underneath the display.
6.2 To adjust the tilt angle, press adjustment button as indicated
direction. The tilt angle is limited to a minimum of 34 degree and
a maximum to 70 degrees.
6.3 After tilt angle has been adjusted, release the button. When
adjustment button released, LCD angle is locked.
6

7. VESA Mounting
SxxxxADTR-IP66 is designed to be fitted with a desk stand base unit or
with a VESA standard mounting bracket or arm (75mmX75mm or
100mm X 100 mm) if required.
Note ： The length of M4 screws must not exceed 8mm
7.1 Unscrew the two M4x8L thumbscrews that secured the base unit
to SxxxxADTR-IP66.
7.2 Separate SxxxxADTR-IP66 from the base unit by lifting the LCD
panel.
7

7.3 Place AC Power Adapter into the Power Adapter Cover. Place
silica gel grommet onto cable and fit into it’s matching position on
the Power Adapter Cover. The empty holes in silica gel grommets
where cables are not installed are fitted with Silica gel plug to
provide water resistance. Then, use Velcro to fasten AC Power
Adapter.
7.4 With each I/O cable in position, tighten the cable fixing panel by two
M3 x 15L screws. Then, secure the AC Power Adapter Cover to the
SxxxxADTR-IP66 back cover by eight M3 x 6L screws.
8

7.5 Use four M4x8L screws to secure SxxxxADTR-IP66 onto any
VESA standard mounting bracket or arm.
M ounting on the ceiling
The cable assembling
sequence as follows.
1. DC IN cable x 1
2. SCSI Printer cable x 1
3. RS232 x 4
4. LAN x 1
5. PS2/KB x 1
6. USB cable x 2
7. Audio cable x 1
8. Microphone cable x 1
9