Ibiza LMH350LED User manual

©Copyright LOTRONIC 2012 LMH350LED Page 1
M
MI IN NI I W WA AS SH H
M
MO OV VI IN NG G
H
HE EA AD D
Ref.: LMH350LED (15-1250)
USER MANUAL
MANUEL D’UTILISATION
BEDIENUNGSANLEITUNG
MANUAL DE INSTRUÇÕES
MANUAL DE UTILIZARE
NAVODILA ZA UPORABO
HANDLEIDING
IMPORTANT NOTE: Electric products must not be put into household waste. Please bring them to a recycling centre. Ask your local authorities or
your dealer about the way to proceed.
NOTE IMPORTANTE : Les produits électriques ne doivent pas être mis au rebut avec les ordures ménagères. Veuillez les faire recycler là où il existe
des centres pour cela. Consultez les autorités locales ou votre revendeur sur la façon de les recycler.
WICHTIGER HINWEIS: Elektrogeräte gehören nicht in den Hausmüll. Sie müssen in speziellen Betrieben recycelt werden. Bringen Sie sie zu einer
speziellen Entsorgungsstelle für Elektrokleingeräte (Wertstoffhof)!
BELANGRIJK: De elektrische producten mogen niet naast het huisvuil geplaatst worden. Gelieve deze te laten recycleren daar waar er centra’s hiervoor voorzien
is. Raadpleeg de plaatselijke autoriteiten of uw verkoper ivm de manier van recycleren.
NOTA IMPORTANTE: Produtos eléctricos não deverão ser postos em contentores de lixo caseiros. Por favor, deposite-os em contentores para reciclagem.
Questione as autoridades locais ou onde adquiriu o produto sobre como deverá proceder.
NOTA IMPORTANTE: Produtos eléctricos não deverão ser postos em contentores de lixo caseiros. Por favor, deposite-os em contentores para reciclagem.
Questione as autoridades locais ou onde adquiriu o produto sobre como deverá proceder.
WAŻNA UWAGA: Elektryczne produkty nie mogą być wyrzucane wraz z odpadami domowymi. Prosimy o przyniesienie ich do centrum recyklingu. Zapytaj
sprzedawcę o sposób postępowania.
NOTA IMPORTANTA: Deseurile care provin de la produsele electrice si electronice nu se vor pune la gunoiul menajer. Dezafectarea acestora trebuie sa se faca la
centrele de colectare special amenajate. Contactati autoritatile locale pentru informatii privind procedura de dezafectare a deseurilor electrice si electronice.

©Copyright LOTRONIC 2012 LMH350LED Page 2
1. BEFORE YOU BEGIN
Contents of the carton:
•1 x Mini wash
•1x Mains lead
•1x User Manual
Unpacking Instructions
Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are
present and have been received in good condition. Notify the freight company immediately and retain packing
material for inspection if any parts appear to be damaged from shipping or the carton itself shows signs of
mishandling. Keep the carton and all packing materials. In the event that a fixture must be returned to the factory, it
is important that the fixture be returned in the original factory box and packing.
Safety Instructions
Please read these instructions carefully, they include important information about the installation, usage and
maintenance of this product.
• Please keep this User Guide for future reference. If you sell the unit to another user, be sure that he also receives
this instruction booklet.
• Always make sure that you are connecting to the proper voltage, and that the line voltage you are connecting to is
not higher than that stated on the decal or rear panel of the fixture.
• This product is intended for indoor use only!
• To prevent risk of fire or shock, do not expose fixture to rain or moisture. Make sure there are no flammable
materials close to the unit while operating.
• The unit must be installed in a location with adequate ventilation, at least 20in (50cm) from adjacent surfaces. Be
sure that no ventilation slots are blocked.
• Always disconnect from power source before servicing or replacing fuse and be sure to replace with same fuse size
and type.
• Secure fixture to fastening device using a safety chain. Never carry the fixture solely by its head. Use its carrying
handles.
• Maximum ambient temperature (Ta) is 104° F (40°C). Do not operate the fixture at temperatures higher than this.
•In the event of a serious operating problem, stop using the unit immediately. Never try to repair the unit by
yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest
authorized technical assistance center. Always use the same type of spare parts.
• Don’t connect the device to a dimmer pack.
• Make sure the power cord is never crimped or damaged.
• Never disconnect the power cord by pulling or tugging on the cord.
• Avoid direct eye exposure to the light source while it is on.
Specifications
Feature: This machine comes with elapsed time display and intelligent temperature control display to ensure the
lamp life. Use ultra-quiet motor to meet the needs of the modern stage.
Voltage: ................................................................................................................. 220-240V∼50/60Hz
Fuse: ............................................................................................................................... 3A 250V
Power consumption: ........................................................................................68.1W (0.30A), Max. at 230V
GB

©Copyright LOTRONIC 2012 LMH350LED Page 3
Light source: ...........................................................................................7pcs of 10W 4 in 1 LED, RGBW
Pan: ....................................................................................................................180°, 360°, 540°
Tilt: ................................................................................................................................90°, 180°
Function: ..........................................Sound
control, Auto-run, Master/Slave, DMX 512, Strobe
Max. Ta................................................................................................................................. 40°C
Channel: ...................................................................................................8 or 13 DMX channels
Data input.................................................................................... Locking 3-pin XLR male socket
Data output ............................................................................Locking 3-pin DMX female socket
Data pin configuration ................................................................. Pin1 shield, pin 2 (-), pin 3 (+)
Dimensions.......................................................................... 225 (L) x 225 (W) x 270mm (H) mm
N.W: ....................................................................................................................................2.7kg
DMX Channels
In 8 channel mode
Channel Function
1
PAN
2
TILT
3
DIMMER & STROBE
4
Red
5
Green
6
Blue
7
White
8
Pan/Tilt SPEED
13 DMX channel mode
Channel
Function
1
PAN
2
PAN FINE
3
TILT
4
TILT FINE
5
PAN/TILT SPEED
6
DIMMER & STROBE
7
RED
8
GREEN
9
BLUE
10
WHITE
11
COLOR
12
COLOR SPEED
13
MOVEMENT (AUTO & SOUND CONTROL)
3. SETUP
Disconnect the power cord before replacing a fuse and always replace with the same type fuse.

©Copyright LOTRONIC 2012 LMH350LED Page 4
Fuse Replacement
With a flat head screwdriver wedge the fuse holder out of its housing.
Remove the damaged fuse from its holder and replace with exactly the same type of fuse.
Insert the fuse holder back in its place and reconnect power.
The fuse is located inside this compartment. Remove using a flat head screwdriver.
Fixture Linking
You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to run
synchronized shows on two or more fixtures set to a master/slave operating mode. The combined number of
channels required by all fixtures on a serial data link determines the number of fixtures that the data link can
support.
Important: Fixtures on a serial/data link must be daisy chained in one single line. Maximum recommended serial
data link distance: 500 meters (1640 ft.) Maximum recommended number of fixtures on a serial data link: 32 fixtures
Data Cabling
To link fixtures together you must use data cables. If you choose to create your own cable, please use data-grade
cables that can carry a high quality signal and are less prone to electromagnetic interference.
CABLE CONNECTORS
Cabling must have a male XLR connector on one end and a female XLR connector on the other end.
DMX connector configuration
Termination reduces signal errors. To avoid signal transmission problems and interference, it is always advisable to
connect a DMX signal terminator.
CAUTION
Do not allow contact between the common and the fixture’s chassis ground. Grounding the common can cause a
ground loop, and your fixture may perform erratically. Test cables with an ohm meter to check correct polarity and
to make sure the pins are not grounded or shorted to the shield or each other.
3-PIN TO 5-PIN CONVERSION CHART
Note! If you use a controller with a 5-pin DMX output connector, you will need to use a 5-pin to 3-pin adapter.
The chart below details a proper cable conversion:
3 PIN TO 5 PIN CONVERSION CHART
Conductor 3 Pin Female (output) 5 Pin Male (Input)
Ground/Shield Pin 1 Pin1
Data (-) signal Pin 2 Pin 2
Data (+) signal Pin 3 Pin 3
Do not use Do not use
Do not use Do not use
Setting up a DMX Serial Data Link
1. Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin connector of the controller.
2. Connect the end of the cable coming from the controller which will have a (female) 3 pin connector to the input
INPUT
COMMON
DMX +
DMX-
Resistance 120 ohm
1/ 4w between pin 2
(DMX-) and pin 3
(DMX+) of the last
fixture.

©Copyright LOTRONIC 2012 LMH350LED Page 5
connector of the next fixture consisting of a (male) 3 pin connector.
3. Then, proceed to connect from the output as stated above to the input of the following fixture and so on.
Master/Slave Fixture Linking
1. Connect the (male) 3 pin connecter side of the DMX cable to the output (female) 3 pin connecter of the first
fixture.
2. Connect the end of the cable coming from the first fixture which will have a (female) 3 pin connecter to the input
connecter of the next fixture consisting of a (male) 3 pin connecter. Then, proceed to connect from the output as
stated above to the input of the following fixture and so on
Often, the set up for Master-Slave and Stand-alone operation requires that the first fixture in the chain be initialized
for this purpose via either settings in the control panel or DIP-switches. Secondarily, the fixtures that follow may also
require a slave setting. Please consult the '' Operating Instructions» section in this manual for complete instructions
for this type of setup and configuration.
4. OPERATING INSTRUCTIONS
4.1 Navigation through the Control Panel
Access control panel functions using the four panel buttons located directly underneath the LCD Display.
Button
Function
<MODE/ESC>
Used to access the menu or to return to a previous menu option
<UP>
<DOWN>
Scrolls through menu options in ascending order
Scrolls through menu options in descending order
<ENTER>
Used to select and store the current menu or option within a menu
When a menu function is selected, the display will show immediately the first
available option for the selected menu function. To select a menu item, press <ENTER>.
4.2 Menu map
Six distinct operating modes, many with sub-modes, are supported by the unit. Press the <MODE/ESC> button
repeatedly until you reach the desired menu function. Use the <UP> and <DOWN> buttons to navigate the menu
options. Press the <ENTER> button to select the menu function currently displayed or to enable a menu option. To
return to the previous option or menu without changing the value, press the <MODE/ESC> button. After a few
seconds, the LED Display will back during operation until another button is pressed.
4.3 User configurations
Setting Maximum Pan Angles
To select, use the “MODE/ESC” button and choose “PA18”, “PA36”,or “PA54”. “UP” and “DOWN” buttons cycle
between all available Pan Angles. Press the “ENTER” button to confirm the chosen selection.
LED Display
Maximum Pan
PA18
180º
PA36
360º
PA54
540º
Setting Maximum Tilt Angles
To select, use the “MODE/ESC” button and choose “t.9” or “t.18” “UP” and “DOWN” buttons cycle between all
available Tilt Angles. Press the “ENTER” button to confirm the chosen selection.

©Copyright LOTRONIC 2012 LMH350LED Page 6
LED Display
Maximum Tilt
t.9
90º
t.18
180º
a-Built-in Program Mode
As the unit can be mounted hung on a truss system or stand on a flat surface, pan, tilt and LED display settings can
be reversed to provide correct coverage and ease of use.
Setting Reversed or Normal Pan
Press the “MODE/ESC” button and choose “Pan”(normal) or “r Pan” (reversed). “UP” and “DOWN” buttons cycle
between the two settings. Press the “ENTER” button to confirm the selection
Setting Reversed or Normal Tilt
Press the “MODE/ESC” button and choose “t.L” (normal) or “rt.l”(reversed).“UP” and “DOWN” buttons cycle
between the two settings. Press the “ENTER” button to confirm the selection
Setting Reversed or Normal LED Display
Press the “MODE/ESC” button and choose “d.s”(normal) or “rd.s”(reversed). “UP” and “DOWN” buttons cycle
between the two settings. Press the “ENTER” button to confirm the selection
b-Auto Run Mode
One of two Auto Run Sub-modes can be selected with a choice of preset speeds .This mode enables the unit to act as
a Master to other Slave units
Choosing Auto Run Sub-modes
Press the “MODE/ESC” button to display “NAFA” or “NASL”. “UP” and “DOWN” buttons change between the two
initial options. With the appropriated option selected, use “ENTER” to confirm and the LED Display will change to:
“Fast” (fast) or “SloU” (slow). The unit will then run at the selected speed
Initial LED Display
Second LED Display
Sub-mode
NAFA
Fast
Fast Auto Run
NAFL
SloU
Slow Auto Run
c-Sound Activated Mode
The unit responds to sounds picked up by the built-in microphone to create a light show. The sound changes the
color and the position of the effect. This mode enables the unit to act a Master to other Slave units
Selection of Sound Activated mode
Press the “MODE/ESC” button and choose “NStS”. When the “ENTER” button is pressed the LED Display changes to
“SrUn” and the unit enters Sound Activated Mode.
Initial LED Display
Second LED Display
Sub-mode
NStS
SrUn
Sound Activated

©Copyright LOTRONIC 2012 LMH350LED Page 7
d- Slave Mode
Up-to 32 units can be daisy chained together with one single unit acting as Master and all other linked units acting as
Slaves. Slave units will all run in sync with the master unit without the need for an additional controller. Connections
can be made using standard DMX control cables with Master unit running in Auto Run or Sound Activated Modes
and placed at the beginning of the chain
Selection of Slave Mode
Press the “MODE/ESC” button and choose “SLAu”. When the “ENTER” button is pressed, the LED display changes to
“Son” and the unit will be slaved to control signals coming from a Master unit
e- Service Modes
After major configuration changes, it may be necessary to reboot or reset the unit.
Resetting the Unit
Press the “MODE/ESC” button and choose “rEST”(restore). Press “ENTER” to confirm. The unit powers itself down
and then on again for a few seconds. During this time, the LED display will scroll “rEST” from left to right, after which
normal operation recommences.
Restoring factory defaults
Press the “MODE/ESC” button and choose “LoAD”(load). Press “ENTER” to confirm. The LED display will change to
“d001” to confirm a factory reset has been completed
Initial start-up
During the warm up time, the unit will auto test itself for a few seconds. During this time the LED display will scroll
“rEST” from left to right .The unit then start to operate normally
f- DMX Modes
The unit supports 8 and 13 channel DMX Sub-modes from a standard controller. When a suitable DMX connection is
made, the “decimal point” in “d.001” will flash.
Setting DMX Addresses
Use the “MODE/ESC” button to display “d001”, “UP” and “DOWN” buttons allows individual DMX addresses to be
set from “d001” to “d512”
Choosing between DMX Sub-modes
The LED display shows the chosen control mode when the “MODE” button is pressed. Use “UP” and “DOWN”
buttons to choose the appropriated DMX control Mode
LED Display
DMX Sub-mode
8CH
8Channel
13CH
13channel
Color Options
The Unit offers a range of 16 preset colors. These can be individually selected with DMX control and feature in Auto
Run Sound Active modes.

©Copyright LOTRONIC 2012 LMH350LED Page 8
Color Options
Color Preset
White
Red
Dark Green
Dark Blue
Light Blue
Magenta
Yellow
Purple
Orange
Light Green
Pink
Brown
Gold
Crimson
Violet
Dark Purple
4.4 DMX channel Values
In 8 channel mode
Channel Function
1 0-255
PAN
2
0-255
TILT
3
0-7
8-134
135-239
240-255
DIMMER & STROBE
blank
Dimmer
Strobe from 0Hz to 40Hz
Open
4
0-255
Red
5
0-255
Green
6
0-255
Blue
7
0-255
White
8
0-255
Pan/Tilt speed
In 13 channel mode
Channel Function
1
0-255
PAN
2
0-255
PAN FINE
3
0-255
TILT
4
0-255
TILT FINE
5 0-255
PAN/TILT SPEED
From Fast to Slow
6
0-7
8-134
135-239
240-255
DIMMER & STROBE
Closed
Dimmer
Strobe from 0Hz to 40Hz
Open
7
0-255
RED

©Copyright LOTRONIC 2012 LMH350LED Page 9
8
0-255
GREEN
9
0-255
BLUE
10
0-255
White
11
0-255
0-7
8-21
22-34
35-49
50-63
64-77
78-91
92-105
106-119
120-134
135-147
148-161
162-175
176-189
190-203
204-217
218-231
232-255
COLOR
Blank
White
Red
Dark Green
Dark Blue
Light Blue
Magenta
Yellow
Purple
Orange
Light Green
Pink
Brown
Gold
Crimson
Violet
Dark Purple
Color Change
12
0-255
COLOR SPEED
13
0-7
8-22
23-37
38-53
54-67
68-82
83-97
98-112
113-127
128-142
143-157
158-172
173-187
188-202
203-217
218-232
233-255
MOVEMENT (AUTO & SOUND EFFECT)
Blank
Auto 1
Auto 2
Auto 3
Auto 4
Auto 5
Auto 6
Auto 7
Auto 8
Sound 1
Sound 2
Sound 3
Sound 4
Sound 5
Sound 6
Sound 7
Sound 8

©Copyright LOTRONIC 2012 LMH350LED Page 10
1. PREPARATIFS
Contenu de l’emballage:
•1 effet de lumière Mini Wash
•1 cordon secteur
•Mode d’emploi
Déballage
Dès réception de l’appareil, ouvrez le carton et vérifiez que le contenu est complet et en bon état. Sinon, prévenez
immédiatement le transporteur et conservez l’emballage s’il montre des signes de mauvais traitements. Conservez le
carton et tous les matériaux d’emballage afin de pouvoir transporter l’appareil en toute sécurité.
Consignes de sécurité
Lisez attentivement ce manuel qui contient des informations importantes sur l’installation, l’utilisation et l’entretien
de cet appareil.
• Conservez le manuel pour référence ultérieure. Si l’appareil change un jour de propriétaire, assurez-vous que le
nouvel utilisateur est en possession du manuel.
• Assurez-vous que la tension secteur convient à cet appareil et qu’elle ne dépasse pas la tension d’alimentation
indiqué sur la plaque signalétique de l’appareil.
• Uniquement pour utilisation à l’intérieur!
• Afin d’éviter tout risque d’incendie ou de choc électrique, ne pas exposer cet appareil à la pluie ou à l’humidité.
Assurez-vous qu’aucun objet inflammable ne se trouve à proximité de l’appareil pendant son fonctionnement.
• Installez l’appareil à un endroit bien ventilé à une distance minimum de 50cm de toute surface. Assurez-vous que
les fentes de ventilation ne sont pas bloquées.
• Débranchez l’appareil du secteur avant toute manipulation ou entretien. Lorsque vous remplacez le fusible, utilisez
uniquement un fusible qui présente exactement les mêmes caractéristiques que l’ancien.
• Sécurisez l’appareil sur le dispositif de fixation au moyen d’une chaîne. Ne portez jamais l’appareil en le tenant par
le boîtier. Tenez-le par l’étrier.
• La température ambiante ne doit pas dépasser 40°C. Ne pas faire fonctionner l’appareil à des températures
supérieures.
• En cas de dysfonctionnement, arrêtez immédiatement l’appareil. N’essayez jamais de réparer l’appareil par vous-
même. Une réparation mal faite peut entraîner des dommages et des dysfonctionnements. Contactez un service
technique agréé. Utilisez uniquement des pièces détachées identiques aux pièces d’origine.
• Ne pas brancher l’appareil sur un variateur.
• Assurez-vous que le cordon d’alimentation n’est jamais écrasé ni endommagé.
• Ne jamais débrancher l’appareil en tirant sur le cordon.
• Ne pas exposer vos yeux à la source lumineuse.
Caractéristiques
Cet appareil affiche le temps d’utilisation et contrôle la température afin de prolonger la durée de vie. Le
moteur ultra-silencieux répond aux besoins de la scène d’aujourd’hui.
Tension d’alimentation: ..................................................................................... 220-240V∼50/60Hz
Source lumineuse: ...................................................................................... 7 LED de 10W, 4 en 1 RVBB
Pan: ............................................................................................................... 180°, 360° ou 540°
Tilt: ............................................................................................................................90° ou 180°
Fonction: ...Commandé par la musique, automatique, maître/esclave, DMX512, stroboscope
F