IBM iSCSI Host Bus Adapter User manual

System i and System p
iSCSI Host Bus Adapter for IBM BladeCenter,
System x, or xSeries


System i and System p
iSCSI Host Bus Adapter for IBM BladeCenter,
System x, or xSeries


Note
Before using this information and the product it supports, read the information in “Notices” on
page 39 and the IBM Systems Safety Information manual, G229-9054.
Fourth Edition (September 2007)
© Copyright International Business Machines Corporation 2004, 2007.
US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract
with IBM Corp.

Contents
Safety and environmental notices ........................v
About this topic ................................ix
iSCSI Host Bus Adapter for IBM BladeCenter, System x, or xSeries ..........1
PDF file for iSCSI Host Bus Adapter for IBM BladeCenter, System x, or xSeries .............2
iSCSI prerequisites .................................3
iSCSI IBM System x or xSeries prerequisites ........................3
iSCSI blade server prerequisites ............................4
Prepare your system ..............................5
Prepare your System x or xSeries server ..........................5
Preparing the System x or xSeries hardware ........................5
Update the System x or xSeries firmware and configure the server ................5
Update System x or xSeries system BIOS .........................5
Update System x or xSeries Baseboard Management Controller firmware ..............6
Update firmware and configure System x or xSeries Remote Supervisor Adapter II ...........6
Update RSA II firmware .............................7
Configure the RSA II ..............................8
Update the System x or xSeries iSCSI HBA firmware .....................8
Set the System x or xSeries start options .........................9
Configure the Baseboard Management Controller ......................9
Complete the xSeries configuration ..........................10
Prepare your blade server ..............................10
Assemble the BladeCenter and blade server hardware ....................10
Update and configure BladeCenter chassis ........................11
Update the BladeCenter management module firmware ...................11
Configure the management module ..........................12
Update the blade server Baseboard Management Controller firmware ...............12
Verify blade server information ............................13
Update and configure BladeCenter I/O module ......................14
Update the blade server BIOS ............................14
Update the blade iSCSI HBA firmware .........................14
Set the blade start options .............................15
Complete the blade server configuration.........................15
Configure iSCSI HBA .............................17
Initial configuration of an iSCSI HBA...........................17
Start the iSCSI HBA configuration utility ........................17
Configure the boot iSCSI HBA ............................18
Configure a new iSCSI HBA for dynamic addressing ...................18
Configure iSCSI HBA for manual addressing ......................19
Configure iSCSI HBA port settings ..........................20
Disable boot for additional iSCSI HBA ports .......................20
End the configuration utility.............................21
Cable the network ...............................23
Related procedures ..............................25
Related System x or xSeries procedures ..........................25
Download System x or xSeries firmware.........................25
Download System x or xSeries BIOS firmware......................25
Download the Baseboard Management Controller firmware update...............26
Download Remote Supervisor Adapter II (RSA II) firmware .................26
© Copyright IBM Corp. 2004, 2007 iii

Download iSCSI HBA update for System x or xSeries ...................27
Alternate method to update Remote Supervisor Adapter II network configuration to defaults .......27
Related BladeCenter and blade server procedures ......................28
Download BladeCenter or blade server firmware ......................28
Download the blade server BIOS ..........................28
Download the BladeCenter Baseboard Management Controller firmware update ..........28
Download BladeCenter management module firmware ...................29
Download the BladeCenter I/O module firmware update ..................29
Download the iSCSI HBA update for blade servers ....................29
Alternate method to update the blade server Baseboard Management Controller ...........30
Related iSCSI HBA configuration procedures ........................30
Start the iSCSI HBA configuration utility ........................30
Restore the factory defaults .............................31
Resetting the cached iSCSI initiator configuration information .................31
Using the ping utility ...............................32
Change CHAP secret ...............................32
Change the maximum transmission unit (MTU) ......................33
End the configuration utility.............................33
Remove and replace the System x, xSeries, or blade server iSCSI HBA........35
Stop the iSCSI integrated System x, xSeries, or blade server ...................35
Remove the System x, xSeries, or blade server iSCSI HBA ....................35
Replace the System x, xSeries, or blade server iSCSI HBA ....................35
Configure the replacement iSCSI HBA ..........................35
Obtain and update remote system network server configuration object information ..........36
Complete the replacement iSCSI HBA configuration .....................36
Appendix. Accessibility features.........................37
Notices ...................................39
Trademarks ...................................40
Electronic emission notices ..............................40
Class A Notices .................................40
Class B Notices .................................44
Terms and conditions ................................46
iv System i and System p: iSCSI Host Bus Adapter for IBM BladeCenter, System x, or xSeries

Safety and environmental notices
Safety notices may be printed throughout this guide:
vDANGER notices call attention to a situation that is potentially lethal or extremely hazardous to
people.
vCAUTION notices call attention to a situation that is potentially hazardous to people because of some
existing condition.
vAttention notices call attention to the possibility of damage to a program, device, system, or data.
World Trade safety information
Several countries require the safety information contained in product publications to be presented in their
national languages. If this requirement applies to your country, a safety information booklet is included
in the publications package shipped with the product. The booklet contains the safety information in
your national language with references to the U.S. English source. Before using a U.S. English publication
to install, operate, or service this product, you must first become familiar with the related safety
information in the booklet. You should also refer to the booklet any time you do not clearly understand
any safety information in the U.S. English publications.
Laser safety information
IBM®System i®models and System p®servers can use I/O cards or features that are fiber-optic based
and that utilize lasers or LEDs.
Laser compliance
All lasers are certified in the U.S. to conform to the requirements of DHHS 21 CFR Subchapter J for class
1 laser products. Outside the U.S., they are certified to be in compliance with IEC 60825 as a class 1 laser
product. Consult the label on each part for laser certification numbers and approval information.
CAUTION:
This product might contain one or more of the following devices: CD-ROM drive, DVD-ROM drive,
DVD-RAM drive, or laser module, which are Class 1 laser products. Note the following information:
vDo not remove the covers. Removing the covers of the laser product could result in exposure to
hazardous laser radiation. There are no serviceable parts inside the device.
vUse of the controls or adjustments or performance of procedures other than those specified herein
might result in hazardous radiation exposure.
(C026)
CAUTION:
Data processing environments can contain equipment transmitting on system links with laser modules
that operate at greater than Class 1 power levels. For this reason, never look into the end of an optical
fiber cable or open receptacle. (C027)
CAUTION:
This product contains a Class 1M laser. Do not view directly with optical instruments. (C028)
CAUTION:
Some laser products contain an embedded Class 3A or Class 3B laser diode. Note the following
information: laser radiation when open. Do not stare into the beam, do not view directly with optical
instruments, and avoid direct exposure to the beam. (C030)
© Copyright IBM Corp. 2004, 2007 v

Power and cabling information for NEBS (Network Equipment-Building System)
GR-1089-CORE
The following comments apply to the IBM System i models and IBM System p servers that have been
designated as conforming to NEBS (Network Equipment-Building System) GR-1089-CORE:
The equipment is suitable for installation in the following:
vNetwork telecommunications facilities
vLocations where the NEC (National Electrical Code) applies
The intrabuilding ports of this equipment are suitable for connection to intrabuilding or unexposed
wiring or cabling only. The intrabuilding ports of this equipment must not be metallically connected to the
interfaces that connect to the OSP (outside plant) or its wiring. These interfaces are designed for use as
intrabuilding interfaces only (Type 2 or Type 4 ports as described in GR-1089-CORE) and require isolation
from the exposed OSP cabling. The addition of primary protectors is not sufficient protection to connect
these interfaces metallically to OSP wiring.
Note: All Ethernet cables must be shielded and grounded at both ends.
The ac-powered system does not require the use of an external surge protection device (SPD).
The dc-powered system employs an isolated DC return (DC-I) design. The DC battery return terminal
shall not be connected to the chassis or frame ground.
Product recycling and disposal
This unit must be recycled or discarded according to applicable local and national regulations. IBM
encourages owners of information technology (IT) equipment to responsibly recycle their equipment
when it is no longer needed. IBM offers a variety of product return programs and services in several
countries to assist equipment owners in recycling their IT products. Information on IBM product
recycling offerings can be found on IBM’s Internet site at http://www.ibm.com/ibm/environment/
products/prp.shtml.
Esta unidad debe reciclarse o desecharse de acuerdo con lo establecido en la normativa nacional o local
aplicable. IBM recomienda a los propietarios de equipos de tecnología de la información (TI) que reciclen
responsablemente sus equipos cuando éstos ya no les sean útiles. IBM dispone de una serie de programas
y servicios de devolución de productos en varios países, a fin de ayudar a los propietarios de equipos a
reciclar sus productos de TI. Se puede encontrar información sobre las ofertas de reciclado de productos
de IBM en el sitio web de IBM http://www.ibm.com/ibm/environment/products/prp.shtml.
Note: This mark applies only to countries within the European Union (EU) and Norway.
Appliances are labeled in accordance with European Directive 2002/96/EC concerning waste electrical
and electronic equipment (WEEE). The Directive determines the framework for the return and recycling
of used appliances as applicable throughout the European Union. This label is applied to various
products to indicate that the product is not to be thrown away, but rather reclaimed upon end of life per
this Directive.
vi System i and System p: iSCSI Host Bus Adapter for IBM BladeCenter, System x, or xSeries

In accordance with the European WEEE Directive, electrical and electronic equipment (EEE) is to be
collected separately and to be reused, recycled, or recovered at end of life. Users of EEE with the WEEE
marking per Annex IV of the WEEE Directive, as shown above, must not dispose of end of life EEE as
unsorted municipal waste, but use the collection framework available to customers for the return,
recycling, and recovery of WEEE. Customer participation is important to minimize any potential effects of
EEE on the environment and human health due to the potential presence of hazardous substances in EEE.
For proper collection and treatment, contact your local IBM representative.
Battery return program
This product may contain sealed lead acid, nickel cadmium, nickel metal hydride, lithium, or lithium ion
battery. Consult your user manual or service manual for specific battery information. The battery must be
recycled or disposed of properly. Recycling facilities may not be available in your area. For information
on disposal of batteries outside the United States, go to http://www.ibm.com/ibm/environment/
products/batteryrecycle.shtml or contact your local waste disposal facility.
In the United States, IBM has established a return process for reuse, recycling, or proper disposal of used
IBM sealed lead acid, nickel cadmium, nickel metal hydride, and other battery packs from IBM
Equipment. For information on proper disposal of these batteries, contact IBM at 1-800-426-4333. Please
have the IBM part number listed on the battery available prior to your call.
For Taiwan: Please recycle batteries.
For the European Union:
Note: This mark applies only to countries within the European Union (EU).
Batteries or packaging for batteries are labeled in accordance with European Directive 2006/66/EC
concerning batteries and accumulators and waste batteries and accumulators. The Directive determines
the framework for the return and recycling of used batteries and accumulators as applicable throughout
the European Union. This label is applied to various batteries to indicate that the battery is not to be
thrown away, but rather reclaimed upon end of life per this Directive.
In accordance with the European Directive 2006/66/EC, batteries and accumulators are labeled to
indicate that they are to be collected separately and recycled at end of life. The label on the battery may
also include a chemical symbol for the metal concerned in the battery (Pb for lead, Hg for mercury and
Cd for cadmium). Users of batteries and accumulators must not dispose of batteries and accumulators as
unsorted municipal waste, but use the collection framework available to customers for the return,
recycling, and treatment of batteries and accumulators. Customer participation is important to minimize
any potential effects of batteries and accumulators on the environment and human health due to the
potential presence of hazardous substances. For proper collection and treatment, contact your local IBM
representative.
Safety and environmental notices vii

For California: Perchlorate Material - special handling may apply. See www.dtsc.ca.gov/hazardouswaste/
perchlorate.
The foregoing notice is provided in accordance with California Code of Regulations Title 22, Division 4.5
Chapter 33. Best Management Practices for Perchlorate Materials. This product/part may include a
lithium manganese dioxide battery which contains a perchlorate substance.
IBM Cryptographic Coprocessor Card Return Program
The following information applies only for systems originally sold prior to July 1, 2006:
This machine may contain an optional feature, the cryptographic coprocessor card, which includes a
polyurethane material that contains mercury. Please follow local ordinances or regulations for disposal of
this card. IBM has established a return program for certain IBM Cryptographic Coprocessor Cards. More
information can be found at http://www.ibm.com/ibm/environment/products/prp.shtml.
viii System i and System p: iSCSI Host Bus Adapter for IBM BladeCenter, System x, or xSeries

About this topic
This topic describes how to install, remove and replace the iSCSI Host Bus Adapter (iSCSI HBA) for
attachment of IBM System x®, xSeries®, or blade servers to a partition running the i5/OS®operating
system.
For information about the accessibility features of this product, for users who have a physical disability,
see “Accessibility features,” on page 37.
© Copyright IBM Corp. 2004, 2007 ix

xSystem i and System p: iSCSI Host Bus Adapter for IBM BladeCenter, System x, or xSeries

iSCSI Host Bus Adapter for IBM BladeCenter, System x, or
xSeries
Learn how to install and configure, or remove and replace an iSCSI Host Bus Adapter (HBA).
This is a customer task. You can perform this task yourself, or contact a service provider to perform the
task for you. You might be charged a fee by the service provider for this service.
Important: If you came to these instructions from the iSCSI install read me first Web page continue with
this procedure. The iSCSI HBA initial installation is one part of a larger installation procedure guided by
the iSCSI install read me first Web page. For the installation to be successful, you must follow the full
procedure in order. If you are not following the path in the iSCSI install read me first Web page see
http://www.ibm.com/systems/i/systemx/iscsi/readme/. If you do not follow the full procedure the
installation will not be successful.
During the iSCSI HBA installation procedure, you need to refer to the following documentation to
complete several steps:
vThe worksheets you completed as a part of the iSCSI Network Planning Guide procedure.
vThe documentation, in either hardcopy or on compact disc that came with your IBM System x, xSeries,
or IBM BladeCenter®server.
vThe System i System i integration with BladeCenter and System x Web site. This site has the latest
iSCSI HBA information, including information about i5/OS program temporary fixes (PTFs) that are
required to run the iSCSI HBA environment.
vThe Troubleshooting Web page for integrated server solutions for help troubleshooting the installation.
The iSCSI HBA environment requires that at least one System x, xSeries, or blade server iSCSI HBA
(initiator) is installed in a System x, xSeries, or BladeCenter server and that at least one iSCSI HBA
(target) is installed in the hosting system as shown in the following figure. Multiple iSCSI HBAs can be
installed in either the System x, xSeries, or blade server, or the hosting system. You can perform these
installation steps multiple times to install a multiple adapter environment.
© Copyright IBM Corp. 2004, 2007 1

Related tasks
“Download BladeCenter or blade server firmware” on page 28
Learn how to locate, select, and download the needed firmware updates for your server. Use the
instructions in this section to accomplish these tasks.
Related reference
“Download System x or xSeries firmware” on page 25
Learn how to download the latest firmware for your System x or xSeries server.
“Remove and replace the System x, xSeries, or blade server iSCSI HBA” on page 35
Learn the hardware and software configuration tasks to remove and replace an iSCSI HBA. Use the
instructions in this section to accomplish these tasks.
Integrated server links
http://www.ibm.com/systems/i/systemx/
http://www.ibm.com/systems/i/systemx/iscsi/readme/
http://www.ibm.com/systems/i/systemx/pdf/iscsi_planning.pdf
http://www.ibm.com/systems/i/systemx/troubleshooting.html
PDF file for iSCSI Host Bus Adapter for IBM BladeCenter, System x, or
xSeries
You can view and print a PDF file of this information.
To view or download the PDF version of this document, select iSCSI Host Bus Adapter for IBM®xSeries
or BladeCenter.
Figure 1. Simple iSCSI network
2System i and System p: iSCSI Host Bus Adapter for IBM BladeCenter, System x, or xSeries

Saving PDF files
To save a PDF on your workstation for viewing or printing:
1. Right-click the PDF in your browser (right-click the link above).
2. Click the option that saves the PDF locally.
3. Navigate to the directory in which you want to save the PDF.
4. Click Save.
Downloading Adobe Reader
You need Adobe Reader installed on your system to view or print these PDFs. You can download a free
copy from the Adobe Web site (www.adobe.com/products/acrobat/readstep.html) .
iSCSI prerequisites
Learn the minimum hardware requirements for setting up your iSCSI network.
Ensure that you have the required hosting system hardware:
viSCSI Host Bus Adapter: CCIN 573B for copper cabling, CCIN 573C for fiber optic cabling.
vNetwork adapter
Tip: The network adapter does not need to be dedicated to the iSCSI HBA and might already be
installed.
Ensure that you have the required hardware for an iSCSI network:
vGigabit Ethernet switch (if not using BladeCenter I/O module switch).
vEthernet cables (category 5e or better) or fiber optic cables.
– One from each System x, xSeries, or blade system iSCSI HBA to network.
– One from each hosting system iSCSI HBA to network.
– One from each service processor hardware Ethernet port to network.
– One from hosting system network adapter to network.
– Any additional cables you might need to connect the Ethernet ports on the System x or xSeries
server or BladeCenter to network, if desired.
Ensure that you have additional equipment and supplies you might need:
vAdditional computer with a network interface capable of running web browser software (used to
update and configure service processor hardware on System x, xSeries, or blade system) .
vWritable media diskettes or compact discs.
iSCSI IBM System x or xSeries prerequisites
Learn the minimum requirements for installing an iSCSI in an System x or xSeries server.
Ensure that you have the following before starting your installation:
vDiskless System x or xSeries server.
viSCSI Host Bus Adapter for System x or xSeries server.
vService processor hardware. Refer to the System i integration with BladeCenter and System x Web page
to determine which of the following type of service processor hardware are required:
– One of three versions of Remote Supervisor Adapter II (RSA II,) depending on System x or xSeries
type and model: RSA II, RSA II – EXA, RSA II SlimLine
– Baseboard Management Controller for System x or xSeries models that do not require the RSA II
iSCSI Host Bus Adapter for IBM BladeCenter, System x, or xSeries 3

vMouse, keyboard, and display that can be attached through a KVM switch
vUSB diskette drive. Some System x or xSeries models do not have an integrated diskette drive and
require a diskette drive for firmware updates
vThe documentation that is included with your System x or xSeries server (hardcopy or compact disc)
iSCSI blade server prerequisites
Learn the minimum requirements for a blade server installation.
Ensure that you have the following items before starting your installation:
vDiskless blade server.
vBladeCenter for housing blade servers.
viSCSI expansion card or cards (also referred to as iSCSI HBA). Use one of these for each blade server
you plan to attach.
vManagement module installed in the BladeCenter to function as service processor hardware.
vI/O module in the appropriate BladeCenter I/O bay to support the network connection for the xSeries
or blade system iSCSI expansion card. This I/O module can be an integrated gigabit switch which can
take the place of an external switch in the iSCSI network or a pass-through module which would
require an external switch.
vMouse, keyboard, and display, which can be attached using a KVM switch.
vThe documentation that is included with your BladeCenter, blade server and options – hardcopy, CD,
or both.
4System i and System p: iSCSI Host Bus Adapter for IBM BladeCenter, System x, or xSeries

Prepare your system
If this is the first iSCSI Host Bus Adapter (HBA) to be installed in your xSeries or blade server, follow the
appropriate xSeries or blade server procedure before you install the iSCSI HBA.
“Prepare your System x or xSeries server”
“Prepare your blade server” on page 10
Prepare your System x or xSeries server
You might need to perform assembly, firmware update, and other preparation tasks to ensure your server
is ready for a successful installation. Find instructions in the following sections to accomplish these tasks.
Preparing the System x or xSeries hardware
Locate information to assemble your server hardware.
The first step in preparing a System x or xSeries server is to assemble the hardware. This might include
installing the keyboard, mouse, display, additional processors, additional memory and can also include
options that may be required for the iSCSI Host Bus Adapter (HBA) solution, such as RSA II and the
iSCSI HBA. Refer to System x or xSeries options documentation for details on how to install the System x
or xSeries components.
Important: Do not connect any cables until instructed to do so. Connecting cables at the wrong point in
the installation process may cause problems later.
Update the System x or xSeries firmware and configure the server
Perform the updates on all System x or xSeries servers to be attached.
Update the System x or xSeries server with the latest version of system basic input/output system
(BIOS), Baseboard Management Controller firmware and system processor firmware.
Remember: You might be directed by the installation process on the iSCSI install read me first Web site to
download the updates and return later to this document to apply the updates. If you have not already
downloaded the firmware updates see “Download System x or xSeries BIOS firmware” on page 25.
Update System x or xSeries system BIOS
Preform these updates on all System x or xSeries servers that are to be attached.
Refer to the file named README you printed during the BIOS update download procedure. Use the
README file instructions along with the steps below to perform the update. The README file contains
any changes necessary to the following instructions. Follow the directions in the README file wherever
differences occur.
If you have not downloaded the BIOS update or printed the readme file see “Download System x or
xSeries BIOS firmware” on page 25.
Perform the following steps on the server:
1. Plug the System x or xSeries server ac power cords into a power source. Refer to System x or xSeries
documentation to complete this step.
© Copyright IBM Corp. 2004, 2007 5

2. Turn on the System x or xSeries server and insert the Flash BIOS update media in the appropriate
drive. Refer to the server documentation to complete this step.
3. The system will start off of the media and present a window where you select 1 - Update
POST/BIOS.
4. On the next panel select ’Y’ to move the current POST/BIOS image to the backup ROM location. The
current code is copied to the backup bank immediately.
5. Select N for the next several display prompts until the Save current flash code to disk prompt is
displayed.
6. Select N for the prompt to Save current flash code to disk.
7. Select the appropriate language, if prompted, or select the Update BIOS option. The update begins.
8. When the update is complete, remove the update media and turn the System x or xSeries server
power off. Refer to System x or xSeries server documentation to complete this step.
Update System x or xSeries Baseboard Management Controller
firmware
Learn how to apply the Baseboard Management Controller firmware update using the procedure in this
section.
Refer to the README file printed earlier during the Baseboard Management Controller firmware
download. If you have not already downloaded the README file or the firmware see “Download the
Baseboard Management Controller firmware update” on page 26. Use the README instructions along
with the following steps to perform the update. The README file contains any changes necessary to the
following instructions. Follow the directions in the README file wherever differences occur. The
Baseboard Management Controller firmware should be updated whether or not an RSA II is installed in
the System x or xSeries server.
This procedure should be performed on the System x or xSeries server.
1. Turn on the System x or xSeries server’s power and insert the Baseboard Management Controller
firmware update media in the appropriate drive. Refer to System x or xSeries server documentation to
complete this step.
2. The update will load and start automatically. It can take several minutes to complete.
3. When the update completes, remove the media from the drive and turn off the System x or xSeries
server’s power. Refer to the System x or xSeries server documentation to complete this step.
Update firmware and configure System x or xSeries Remote
Supervisor Adapter II
Learn how to apply the Remote Supervisor Adapter II firmware update and configure the adapter using
the procedures in this section.
You may skip this section If the System x or xSeries server does not have an RSA II installed. Refer to the
iSCSI Network Planning Worksheets, item XSP1, to determine whether or not to continue with this section.
If the System x or xSeries server requires you to install a System x or xSeries Remote Supervisor Adapter
II (RSA II) option, install it before updating the firmware. After the RSA II is installed, connect it using an
Ethernet cable to the Ethernet port on the computer containing the RSA II firmware update. Refer to the
RSA II documentation to complete this action.
Tip: You may need a switch or hub to complete these connections depending on the location of the
System x or xSeries server and the computer containing the update.
If you have not already downloaded the RSA II update see “Download Remote Supervisor Adapter II
(RSA II) firmware” on page 26.
6System i and System p: iSCSI Host Bus Adapter for IBM BladeCenter, System x, or xSeries

The procedure below assumes the RSA II is set to its factory default values. If the RSA II IP address is no
longer known, it can be set back to the defaults, using the Setup utility, by following the instructions in
the section “Alternate method to update Remote Supervisor Adapter II network configuration to
defaults” on page 27.
Refer to the README file printed earlier during the RSA II firmware download. Use the README file
instructions along with the steps below to perform the firmware update. The README file will contain
any changes necessary to the following instructions. Follow the directions in the README file wherever
differences occur.
Note: The following steps are performed on the computer containing the update package (not on the
System x or xSeries console):
Update RSA II firmware
Learn how to apply the RSA II firmware update.
Refer to the README file printed earlier during the RSA II firmware download. Use the README file
instructions along with the following steps to perform the firmware update. The README file can
contain any changes necessary to the following instructions. Follow the directions in the README file
wherever differences occur.
Note: The following steps are performed on the computer containing the update package (not on the
System x or xSeries console):
1. Set the IP address to a value in the same subnet as the RSA II default IP address of 192.168.70.125.
For example you can set the IP address to 192.168.70.101 with a subnet mask of 255.255.255.0.
2. Extract the files from the .zip file that you downloaded earlier to unpack the firmware update files.
3. Ensure the System x or xSeries ac power cords are attached to a power source. Refer to System x or
xSeries documentation to complete this step. Wait at least 30 seconds following this step to allow the
RSA II hardware to start.
4. Open a Web browser. In the address field, type the IP address (192.168.70.125) of the RSA II to which
you want to connect. The Enter Password window opens.
5. Type the user name and password on the Enter Password window. The RSA II has a default user
name of USERID and password of PASSW0RD (where 0 is a zero not the letter O).
6. Select a timeout value on the next screen and click continue.
7. If the next window is the System Status window, on the navigation pane on the left, under Tasks,
click Firmware Update. If the RSA II firmware does not support the server on which it is installed, a
warning window stating that the RSA II does not have firmware that supports the server is
displayed. Click OK to continue.
8. At the next display, select Browse and navigate to the files containing the firmware update. The files
will have an extension of .PKT; and there might be multiple files with this extension.
9. Select one of these files, and then click Open. The full path of the selected file is displayed in the
Browse field.
10. To start the update process, click Update. A progress indicator opens as the file is transferred to
temporary storage on the Remote Supervisor Adapter II. A confirmation window is displayed when
the file transfer is complete.
11. Verify that the file shown on the Confirm Firmware Update window is the one you want to update.
If not, click Cancel.
12. To complete the update process, click Continue. A progress indicator opens as the firmware on the
Remote Supervisor Adapter II is copied. A confirmation window is displayed when the update
completes.
13. Repeat the update procedure for any other .PKT files.
Prepare your system 7

Configure the RSA II
You must configure a number of parameters in the RSA II before proceeding with the installation process.
Refer to section 3.2 in the iSCSI Network Planning Guide for detailed information required to configure the
RSA II. This process picks up from any of the screens after signon on the RSA II web browser interface.
Before you begin: Be sure to have the iSCSI Network Planning Worksheets handy; you will need
information from them as you complete this task.
1. Navigate to the RSA II Web browser interface.
2. Select Login Profiles from under ASM Control in the navigation pane on the left side of the screen.
3. From the list of login IDs, find the entry for the default login ID value of USERID and click that
entry.
4. The Login Profile window is displayed do the following:
a. Change the Login ID (worksheet item XSP7) and fill in the Password (worksheet item XSP8) and
Confirm password fields based on the information entered in the iSCSI Network Planning
Worksheets.
b. Ensure the Authority Level is set to Supervisor.
c. Click Save.
5. On the navigation pane on the left side of the window, select Network Interfaces under ASM
Control to start the configuration.
6. Use the values in the iSCSI Network Planning Worksheets to complete the following steps:
a. Select Enabled from the Interface list.
b. From the DHCP list select and set one of the following (worksheet item XSP3):
1) Disabled - Use static IP configuration.
2) Enabled - Obtain IP config from DHCP server. This option requires an operating DHCP
server when you install the operating system.
c. Enter a name for this RSA II in the Hostname (worksheet item XSP2) field.
d. Enter a value for the following fields under the Static IP Configuration heading need to be filled
in if the Disabled – Use static IP configuration value was selected for the DHCP field above:
vIP address – type in the IP address (worksheet item XSP4).
vSubnet mask – type in the desired subnet mask (worksheet item XSP5).
vGateway address – type in the gateway address (worksheet item XSP6).
e. Click Save to complete configuring the network interfaces.
7. Select System Settings under ASM Control on the navigation pane on the left side of the window.
8. On the next window under the ASM Information heading, use the Host OS list to select a value of
Other.
9. On the same window, under the heading ASM Date and Time, click Set ASM Date and Time.
10. On the next window, set the current date and time (using a 24-hour clock) and use the GMT offset
list to select the appropriate time zone. Also, select the box to automatically adjust for daylight
savings time, if necessary. Click Save to complete.
11. When all the updates and configuration steps are complete, select Restart ASM on the navigation
pane to restart the Remote Supervisor Adapter II.
12. Click OK to confirm that you want to restart the Remote Supervisor Adapter II. A window is
displayed advising that the browser window will be closed. Click OK to continue.
Update the System x or xSeries iSCSI HBA firmware
If update media for the iSCSI HBA firmware was built during the download process, it should be applied
at this time. Use the procedure in this section to accomplish this task.
1. Plug the ac power cords into a power source. Refer to System x or xSeries documentation to complete
this step.
8System i and System p: iSCSI Host Bus Adapter for IBM BladeCenter, System x, or xSeries