IBM TotalStorage NAS 200 25T Programming manual

IBM TotalStorage NAS 200
Model 25T
Quick Start Instructions


First Edition (October 2002)
© Copyright International Business Machines Corporation 2002. All rights reserved.
US Government Users Restricted Rights – Use, duplication or disclosure restricted by
GSA ADP Schedule Contract with IBM Corp.

IBM TotalStorage
™
NAS 200Model 25T Quick Start
Instructions
Step 1: Read this first
Caution:
—Safety Information
Use safe practices when lifting this product.
Do not place any object weighing more than 82 kg (180 lb.) on top of
rack-mounted devices.
Notes:
1. Make sure the rack is stabilized before installing hardware, and always
load it starting at the bottom and moving upward to the top.
2. Visually inspect the unit to ensure that it was not damaged during
shipping. If any items are missing or damaged, contact your IBM
representative.
Step 2: Unpack the box
Items you find in the box (tower and rack configurations):
OR
vModel 25T
vTwo power cables
© Copyright IBM Corp. 2002 1

IBM TotalStorage NAS 200
Hardware Installation Guide
Software CD
Software CD
Software CD
Software CD
Documentation CD
vOne set of documentation including: Caution: Safety
Information – Read This First, IBM TotalStorage NAS 200
Hardware Installation Guide, Quick Start Instructions and
product and documentation CD-ROMs.
Rack configuration only
vOne rack installation kit including: Cable-management
assembly, cable straps, cable ties, cage nuts, clip nuts,
screw packages and slide rails and Rack Mounting
Instructions.
Items you provide
vOne Phillips #2 screwdriver
vOne flat-blade screwdriver
vOne One Ethernet cable (Cat5 copper cable if you are
using a copper Ethernet adapter) with connection
instructions and IP information from your network
administrator.
vOne PC with a subnetwork connection, Windows 2000
or Windows NT 4.0 or later, Swing and XML Java
libraries, Advanced Appliance Configuration application,
and Universal Management Services browser.
Optional service and diagnostic equipment
vOne monitor, keyboard and a PS/2 mouse
2NAS 200 Model 25T Quick Start Instructions

Step 3: Install the appliance
1. Tower configuration only: Place the tower configuration in its final location
and then go to “Step 4: Attach cables (Tower configuration)”on page 6.
Rack configuration only: Mark the rack-configuration location on the rack
by placing the provided stickers over the holes on the front and rear of the
rack indicated by the arrows on the template.
2. Insert the cage nuts using a screwdriver or the cage-nut insertion tool (or
slide on the clip nuts) into each marked hole.
IBM TotalStorage
™
NAS 200Model 25T Quick Start Instructions 3

3. Align each slide rail to the rack using the pin as a guide. Then bolt the
slide rails to the rack using the M6 screws provided.
4. Attach the hinge bracket to the rear of the rack using the M6 screws
provided. Then attach the cable-management assembly to the slide rail by
sliding the hinge pin into the hinge.
4NAS 200 Model 25T Quick Start Instructions

5. Place the engine in the rack by fully extending the slide rails out of the
rack, lifting the engine above the rails, and resting the rack-support wheels
on the slide rails. Then lower the front of the engine onto the slide rails,
ensuring that the bracket notches on the front of the engine fit securely on
the tabs located on the front of the slide rails.
6. Secure the appliance to the rails using the M4 screws provided. Unscrew
the rack-support wheels and store them in a safe place. Go to “Step 5:
Attach cables (Rack configuration)”on page 7.
IBM TotalStorage
™
NAS 200Model 25T Quick Start Instructions 5

Step 4: Attach cables (Tower configuration)
1. Connect the engine to your network by plugging the network cables to the
Ethernet ports and then into your network. Connect each power cable to
the receptacles on the back of the engine and then to different power source
outlets.
2. Route the power and network cables through the cable-restraint brackets on
the rear of the appliance. Go to “Step 7: Power on and verify LED status”
on page 9.
1
2
1
2
1
2
6NAS 200 Model 25T Quick Start Instructions

Step 5: Attach cables (Rack configuration)
1. Connect the engine to your network by pressing in on the safety latches,
sliding the engine halfway into the rack, and plugging the network cables
to the Ethernet ports and then into your network. Connect each power
cable to the receptacles on the back of the engine and then to different
power source outlets.
2. Route the cables through the cable-management assembly on the rack.
A
2
3
1
1
3
1
B
A
B
IBM TotalStorage
™
NAS 200Model 25T Quick Start Instructions 7

Step 6: Complete the installation
Rack configuration only
Complete the installation by sliding the engine into the rack until the release
latches snap shut. Then insert the M6 screws provided through the
release-latch-bracket assembly on either side of the engine.
Note: Inserting the M6 screws is required if the rack is moved or in a
vibration-prone area.
8NAS 200 Model 25T Quick Start Instructions