IBM E400 User manual

IBM E400 PROJECTOR
User’s Guide
򔻐򗗠򙳰

IBM E400 PROJECTOR
User’s Guide
򔻐򗗠򙳰

Anmerkung: Before using this information and the product it supports, read the information in Anhang D, „Ser-
vice
and Support”, auf Seite D-1 and Anhang E, „IBM Statement of Limited Warranty - Z125-4753-07 - 11/2002”,
auf Seite E-1
Second Edition (February 2004)
© Copyright International Business Machines Corporation 2004. Alle Rechte vorbehalten.

Inhaltsverzeichnis
Safety information . . . . . . . . . .v
General safety information . . . . . . vii
Service . . . . . . . . . . . . . . . . vii
Power cords and power adapters . . . . . . . vii
Extension cords and related devices . . . . . . viii
Plugs and outlets . . . . . . . . . . . . viii
Batteries . . . . . . . . . . . . . . . viii
Heat and product ventilation . . . . . . . .ix
CD and DVD drive safety . . . . . . . . . .ix
Registering your option . . . . . . . .xi
Vorwort . . . . . . . . . . . . . . xiii
Kapitel 1. Einführung . . . . . . . . 1-1
Kapitel 2. Projektor einrichten . . . . 2-1
Projektor starten und ausschalten . . . . . . . 2-1
Projektorhöhe anpassen . . . . . . . . . . 2-2
Projektor aufstellen . . . . . . . . . . . 2-3
Zoom-, Fokus- und Trapezfunktion einstellen . . . 2-4
Lautstärke einstellen . . . . . . . . . . . 2-5
Kapitel 3. Einheiten an den Projektor
anschließen . . . . . . . . . . . . 3-1
Einheiten anschließen . . . . . . . . . . . 3-1
Kapitel 4. Funktionen des Projektors
verwenden . . . . . . . . . . . . . 4-1
Fernbedienung verwenden . . . . . . . . . 4-1
Batterien der Fernbedienung einsetzen . . . . . 4-2
Reichweite der Fernbedienung . . . . . . . . 4-3
Tasten am Projektor und auf der Fernbedienung 4-3
Kapitel 5. Menüsteuerung für das
Bildschirmmenü . . . . . . . . . . 5-1
Im Bildschirmmenü navigieren . . . . . . . 5-1
Bildschirmmenüsprache einstellen . . . . . 5-1
Menü ″Quality″ (Qualität) . . . . . . . . 5-2
Menü ″Properties″ (Eigenschaften) . . . . . 5-4
Menü ″Options″ (Optionen) . . . . . . . . 5-5
Menü ″Setup″ (Konfiguration) . . . . . . . 5-7
Menü ″Information″ (Informationen) . . . . . 5-9
Anhang A. Wartung . . . . . . . . . A-1
Linse reinigen . . . . . . . . . . . . . A-1
Projektorlampe austauschen . . . . . . . . A-1
Zeitgeber der Projektorlampe zurücksetzen . . . A-3
Sicherheitsschlitz verwenden . . . . . . . . A-3
Anhang B. Fehlerbehebung . . . . . B-1
Projektoranzeigen . . . . . . . . . . . . B-3
Anhang C. Technische Daten . . . . . C-1
Anhang D. Service and Support . . . D-1
Online technical support . . . . . . . . . D-1
Telephone technical support . . . . . . . . D-1
Anhang E. IBM Statement of Limited
Warranty - Z125-4753-07 - 11/2002 . . . E-1
Part 2 - Country-unique Terms . . . . . . . E-4
Part 3 - Warranty Information . . . . . . . E-15
Anhang F. Notices . . . . . . . . . F-1
Trademarks . . . . . . . . . . . . . . F-2
Electronic emission notices . . . . . . . . . F-2
Federal Communications Commission (FCC) state-
ment
. . . . . . . . . . . . . . . . F-2
© Copyright IBM Corp. 2004 iii

iv IBM E400 PROJECTOR: User’s Guide

Safety information
Before installing this product, read the Safety Information.
Antes de instalar este produto, leia as Informações de Segurança.
Pred instalací tohoto produktu si prectete prírucku bezpecnostních instrukcí.
Læs sikkerhedsforskrifterne, før du installerer dette produkt.
Ennen kuin asennat tämän tuotteen, lue turvaohjeet kohdasta Safety Information.
Avant d’installer ce produit, lisez les consignes de sécurité.
Vor der Installation dieses Produkts die Sicherheitshinweise lesen.
Prima di installare questo prodotto, leggere le Informazioni sulla Sicurezza.
Lees voordat u dit product installeert eerst de veiligheidsvoorschriften.
Les sikkerhetsinformasjonen (Safety Information) før du installerer dette produktet.
Antes de instalar este produto, leia as Informações sobre Segurança.
Antes de instalar este producto lea la información de seguridad.
© Copyright IBM Corp. 2004 v

Läs säkerhetsinformationen innan du installerar den här produkten.
vi IBM E400 PROJECTOR: User’s Guide

General safety information
Always observe the following precautions to reduce the risk of injury and property
damage.
Service
Do not attempt to service a product yourself unless instructed to do so by the IBM
Support Center. Use only an IBM authorized service provider who is approved to
repair your particular product.
Note: Some parts can be upgraded or replaced by the customer. These parts are
referred to as Customer Replaceable Units, or CRUs. IBM expressly identifies CRUs
as such, and provides documentation with instructions when it is appropriate for
customers to replace those parts. You must closely follow all instructions when per-
forming such replacements. Always make sure that the power is turned off and
that the product is unplugged from any power source before you attempt the
replacement. If you have any questions or concerns, contact the IBM Support Cen-
ter.
Power cords and power adapters
Use only the power cords and power adapters supplied by the product manufactu-
rer.
Never wrap a power cord around the power adapter or other object. Doing so can
stress the cord in ways that can cause the cord to fray, crack or crimp. This can
present a safety hazard.
Always route power cords so that they will not be walked on, tripped over, or
pinched by objects.
Protect the cord and power adapters from liquids. For instance, do not leave your
cord or power adapter near sinks, tubs, toilets, or on floors that are cleaned with
liquid cleansers. Liquids can cause a short circuit, particularly if the cord or power
adapter has been stressed by misuse. Liquids can also cause gradual corrosion of
the power cord terminals and/or the connector terminals on the adapter which can
eventually result in overheating.
Always connect power cords and signal cables in the correct order and ensure that
all power cord connectors are securely and completely plugged into receptacles.
Do not use any power adapter that shows corrosion at the ac input pins and/or
shows signs of overheating (such as deformed plastic) at the ac input or anywhere
on the power adapter.
Do not use any power cords where the electrical contacts on either end show signs
of corrosion or overheating or where the power cord appears to have been dama-
ged in any way.
© Copyright IBM Corp. 2004 vii

Extension cords and related devices
Ensure that extension cords, surge protectors, uninterruptible power supplies, and
power strips that you use are rated to handle the electrical requirements of the
product. Never overload these devices. If power strips are used, the load should
not exceed the power strip input rating. Consult an electrician for more informa-
tion
if you have questions about power loads, power requirements, and input
ratings.
Plugs and outlets
If a receptacle (power outlet) that you intend to use with your computer equip-
ment
appears to be damaged or corroded, do not use the outlet until it is replaced
by a qualified electrician.
Do not bend or modify the plug. If the plug is damaged, contact the manufacturer
to obtain a replacement.
Some products are equipped with a three-pronged plug. This plug fits only into a
grounded electrical outlet. This is a safety feature. Do not defeat this safety feature
by trying to insert it into a non-grounded outlet. If you cannot insert the plug into
the outlet, contact an electrician for an approved outlet adapter or to replace the
outlet with one that enables this safety feature. Never overload an electrical outlet.
The overall system load should not exceed 80 percent of the branch circuit rating.
Consult an electrician for more information if you have questions about power
loads and branch circuit ratings.
Be sure that the power outlet you are using is properly wired, easily accessible,
and located close to the equipment. Do not fully extend power cords in a way that
will stress the cords.
Connect and disconnect the equipment from the electrical outlet carefully
Batteries
All IBM personal computers contain a non-rechargeable coin cell battery to provide
power to the system clock. In addition many mobile products such as Thinkpad
notebook PCs utilize a rechargeable battery pack to provide system power when in
portable mode. Batteries supplied by IBM for use with your product have been
tested for compatibility and should only be replaced with IBM approved parts.
Never attempt to open or service any battery. Do not crush, puncture, or incinerate
batteries or short circuit the metal contacts. Do not expose the battery to water or
other liquids. Only recharge the battery pack strictly according to instructions
included in the product documentation.
Battery abuse or mishandling can cause the battery to overheat, which can cause
gasses or flame to “vent” from the battery pack or coin cell. If your battery is
damaged, or if you notice any discharge from your battery or the buildup of
foreign materials on the battery leads, stop using the battery and obtain a replace-
ment
from the battery manufacturer.
Batteries can degrade when they are left unused for long periods of time. For some
rechargeable batteries (particularly Lithium Ion batteries), leaving a battery unused
in a discharged state could increase the risk of a battery short circuit, which could
viii IBM E400 PROJECTOR: User’s Guide

shorten the life of the battery and can also pose a safety hazard. Do not let rechar-
geable Lithium-Ion batteries completely discharge or store these batteries in a
discharged state.
Heat and product ventilation
Computers generate heat when turned on and when batteries are charging. Note-
book PCs can generate a significant amount of heat due to their compact size.
Always follow these basic precautions:
v Do not leave the base of your computer in contact with your lap or any part of
your body for an extended period when the computer is functioning or when
the battery is charging. Your computer produces some heat during normal ope-
ration.
Extended contact with the body could cause discomfort or, potentially,
a skin burn.
v Do not operate your computer or charge the battery near flammable materials or
in explosive environments.
v Ventilation slots, fans and/or heat sinks are provided with the product for safety,
comfort, and reliable operation. These features might inadvertently become blo-
cked
by placing the product on a bed, sofa, carpet, or other flexible surface.
Never block, cover or disable these features.
CD and DVD drive safety
CD and DVD drives spin discs at a high speed. If a CD or DVD is cracked or
otherwise physically damaged, it is possible for the disc to break apart or even
shatter when the CD drive is in use. To protect against possible injury due to this
situation, and to reduce the risk of damage to your machine, do the following:
v Always store CD/DVD discs in their original packaging
v Always store CD/DVD discs out of direct sunlight and away from direct heat
sources
v Remove CD/DVD discs from the computer when not in use
v Do not bend or flex CD/DVD discs, or force them into the computer or their
packaging
v Check CD/DVD discs for cracks before each use. Do not use cracked or dama-
ged discs
General safety information ix

x IBM E400 PROJECTOR: User’s Guide

Registering your option
Thank you for purchasing this IBM
®
product. Please take a few moments to regis-
ter your product and provide us with information that will help IBM to better
serve you in the future. Your feedback is valuable to us in developing products
and services that are important to you, as well as in developing better ways to
communicate with you. Register your option on the IBM Web site at
http://www.ibm.com/pc/register/
IBM will send you information and updates on your registered product unless you
indicate on the Web site questionnaire that you do not want to receive further
information.
© Copyright IBM Corp. 2004 xi

xii IBM E400 PROJECTOR: User’s Guide

Vorwort
Der IBM E400-Projektor kann sowohl für Geschäftspräsentationen als auch für pri-
vate Zwecke verwendet werden. Das Anschließen an andere Geräte, die Verwen-
dung
und die Wartung sind einfach.
Im Lieferumfang des Produkts ist außer dem vorliegenden Benutzerhandbuch Fol-
gendes enthalten:
1 Projektor einschließlich Lampengehäuse und Schutzkappe für die Linse
2 Fernsteuerung
3 Zwei AAA-Batterien
4 USB-Kabel
5 S-Videokabel
6 Videokabel (DVI-DB15) für VGA
7 Audiokabel (Minianschluss - RCA)
8 Netzkabel
9 FBAS-Kabel
© Copyright IBM Corp. 2004 xiii

10 Installations-CD mit Benutzerhandbuch
11 Mehrsprachiges Handbuch zum Schnelleinstieg
12 Transportbehälter
Falls eines der oben aufgeführten Teile fehlt oder beschädigt ist, wenden Sie sich
an die Verkaufsstelle.
Anmerkung: Bewahren Sie den Kaufnachweis sorgfältig auf. Sie brauchen ihn,
wenn Sie den Gewährleistungsservice in Anspruch nehmen möchten.
Informationen zu optionalem Zubehör für den Projektor finden Sie unter der
Adresse http://www.ibm.com.
Achtung:
v Setzen Sie den Projektor nicht in staubiger Umgebung ein.
v Blockieren Sie die Entlüftungsschlitze des Projektors nicht.
v Lassen Sie das Netzkabel zwei bis fünf Minuten lang angeschlossen, bis der Pro-
jektor
Raumtemperatur erreicht hat, bevor Sie ihn im Transportbehälter aus wei-
chem
Material verpacken. Wenn Sie den Projektor nach dem Ausschalten des
Netzstroms zu früh im Transportbehälter verpacken, kann der Projektor sich
überhitzen und die Lebensdauer der Lampe sich verkürzen.
v Stellen Sie sicher, dass die Schutzkappe für die Linse befestigt ist, und verpacken
Sie den Projektor immer im Transportbehälter, damit die Linse nicht beschädigt
wird.
xiv IBM E400 PROJECTOR: User’s Guide

Kapitel 1. Einführung
In den folgenden Abbildungen sind die Komponenten des Projektors dargestellt.
1 Linse/Fokusfunktion
2 Infrarotempfänger
3 Anschlüsse
4 Anschluss für Netzkabel
5 Höhenverstellbarer Fuß
6 Projektorfuß
7 Verstellknopf für Projektorfuß
Abbildung 1-1. Projektoransicht von vorn
© Copyright IBM Corp. 2004 1-1

1 Zoomfunktion
2 Fokusfunktion
3 Netzschalter
4 Systemstatusanzeigen
5 Steuertasten
6 Taste ″Source″ (Signalquelle)
7 Taste ″Menu″ (Menü)
8 Taste ″Auto″ (Automatisch)
9 Lautsprecher
Abbildung 1-2. Projektoransicht von oben
1-2 IBM E400 PROJECTOR: User’s Guide

Abbildung 1-3. Ansicht der Steuertasten und
Anzeigen auf dem Projektor von oben
1 Betriebsanzeige
2 Bereitschaftsanzeige
3 Trapezkorrektur/Aufwärtspfeil
4 Lautstärke/Rechtspfeil
5 Eingabetaste
6 Trapezkorrektur/Abwärtspfeil
7 Lautstärke/Linkspfeil
1 Audioeingang
2 RS-232
3 DVI-I
4 Netzkabelanschluss
5 FBAS-Signal
6 S-Video
7 USB
8 Sicherheitsschlitz
Abbildung 1-4. Anschlüsse
Kapitel 1. Einführung 1-3

1 Abdeckung für Projektorlampe
2 Projektorfuß
3 Höhenverstellbarer Fuß
4 Bohrungen für Deckeninstallation
Abbildung 1-5. Projektoransicht von unten
1-4 IBM E400 PROJECTOR: User’s Guide