IBM 88861TU User manual

IBM BladeCenter S
Type 7779/8886
Installation and User's Guide


IBM BladeCenter S
Type 7779/8886
Installation and User's Guide


Note
Note: Before using this information and the product it supports, read the general information in
“Notices” on page 61; and read the IBM Safety Information and the IBM Systems Environmental
Notices and User Guide on the IBM Documentation CD.
Sixth Edition (December 2010)
© Copyright IBM Corporation 2007, 2010.
US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract
with IBM Corp.

Contents
Safety ...............v
Safety statements ............vi
Chapter 1. Introduction ........1
Related documentation ...........2
The IBM BladeCenter Documentation CD.....3
Notices and statements in this document .....4
Features and specifications..........5
Components of the BladeCenter S system.....6
Front view of the BladeCenter S chassis ....6
Rear view of the BladeCenter S chassis ....13
Systems and storage management .......23
IBM Director .............23
Storage Configuration Manager.......23
Chapter 2. Installing the BladeCenter S
Types 7779 and 8886.........25
Installation guidelines ...........25
System reliability guidelines ........26
Handling static-sensitive devices ......26
Preparing to install your BladeCenter S system . . 27
Verifying ship group contents .......27
Obtaining firmware and device drivers ....27
Obtaining configuration, systems management,
and storage management software......28
Setting up your BladeCenter S system .....28
Removing components .........29
Installing the BladeCenter S chassis in a rack . . 32
Installing components ..........37
Cabling the BladeCenter S chassis ......44
Connecting the BladeCenter S chassis to power 45
Disconnecting power from the BladeCenter unit 45
Chapter 3. Installing IBM Director
Server (optional) ..........47
Chapter 4. Configuring the BladeCenter
S system ..............49
Configuring I/O modules .........49
Configuring blade servers .........50
Selecting shared BladeCenter resources .....52
Appendix A. Getting help and technical
assistance .............53
Before you call .............53
Using the documentation ..........54
Getting help and information from the World Wide
Web.................54
Hardware service and support ........55
Software service and support ........55
IBM Taiwan product service .........55
Appendix B. Parts listing .......57
Front view parts listing ..........57
Rear view parts listing...........58
Notices ..............61
Trademarks ..............62
Important notes .............63
Electronic emission notices .........63
Federal Communications Commission (FCC)
statement ..............63
Industry Canada Class A emission compliance
statement ..............64
Avis de conformité à la réglementation
d'Industrie Canada ...........64
Australia and New Zealand Class A statement . 64
United Kingdom telecommunications safety
requirement .............64
European Union EMC Directive conformance
statement ..............64
Taiwanese Class A warning statement ....65
Chinese Class A warning statement .....65
Japanese Voluntary Control Council for
Interference (FCS) statement ........65
Index ...............67
© Copyright IBM Corp. 2007, 2010 iii

iv BladeCenter S Type 7779/8886: Installation and User's Guide

Safety
Before installing this product, read the Safety Information.
Antes de instalar este produto, leia as Informações de Segurança.
Pred instalací tohoto produktu si prectete prírucku bezpecnostních instrukcí.
Læs sikkerhedsforskrifterne, før du installerer dette produkt.
Lees voordat u dit product installeert eerst de veiligheidsvoorschriften.
Ennen kuin asennat tämän tuotteen, lue turvaohjeet kohdasta Safety Information.
Avant d'installer ce produit, lisez les consignes de sécurité.
Vor der Installation dieses Produkts die Sicherheitshinweise lesen.
© Copyright IBM Corp. 2007, 2010 v

Prima di installare questo prodotto, leggere le Informazioni sulla Sicurezza.
Les sikkerhetsinformasjonen (Safety Information) før du installerer dette produktet.
Antes de instalar este produto, leia as Informações sobre Segurança.
Antes de instalar este producto, lea la información de seguridad.
Läs säkerhetsinformationen innan du installerar den här produkten.
Safety statements
These statements provide the caution and danger information used in this
documentation.
Important:
Each caution and danger statement in this documentation is labeled with a
number. This number is used to cross reference an English-language caution or
danger statement with translated versions of the caution or danger statement in
the Safety Information document.
For example, if a caution statement is labeled “Statement 1”, translations for that
caution statement are in the Safety Information document under “Statement 1”.
Be sure to read all caution and danger statements in this documentation before you
perform the procedures. Read any additional safety information that comes with
your BladeCenter S system or optional device before you install the device.
vi BladeCenter S Type 7779/8886: Installation and User's Guide

Statement 1
DANGER
Electrical current from power, telephone, and communication cables is
hazardous.
To avoid a shock hazard:
vDo not connect or disconnect any cables or perform installation,
maintenance, or reconfiguration of this product during an electrical storm.
vConnect all power cords to a properly wired and grounded electrical outlet.
vConnect to properly wired outlets any equipment that will be attached to
this product.
vWhen possible, use one hand only to connect or disconnect signal cables.
vNever turn on any equipment when there is evidence of fire, water, or
structural damage.
vDisconnect the attached power cords, telecommunications systems,
networks, and modems before you open the device covers, unless
instructed otherwise in the installation and configuration procedures.
vConnect and disconnect cables as described in the following table when
installing, moving, or opening covers on this product or attached devices.
To Connect: To Disconnect:
1. Turn everything OFF.
2. First, attach all cables to devices.
3. Attach signal cables to connectors.
4. Attach power cords to outlet.
5. Turn device ON.
1. Turn everything OFF.
2. First, remove power cords from outlet.
3. Remove signal cables from connectors.
4. Remove all cables from devices.
Safety vii

Statement 2
CAUTION:
When replacing the lithium battery, use only IBM®Part Number 33F8354 or an
equivalent type battery recommended by the manufacturer. If your system has a
module containing a lithium battery, replace it only with the same module type
made by the same manufacturer. The battery contains lithium and can explode if
not properly used, handled, or disposed of.
Do not:
vThrow or immerse into water
vHeat to more than 100°C (212°F)
vRepair or disassemble
Dispose of the battery as required by local ordinances or regulations.
Statement 3
CAUTION:
When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or
transmitters) are installed, note the following:
vDo not remove the covers. Removing the covers of the laser product could
result in exposure to hazardous laser radiation. There are no serviceable parts
inside the device.
vUse of controls or adjustments or performance of procedures other than those
specified herein might result in hazardous radiation exposure.
DANGER
Some laser products contain an embedded Class 3A or Class 3B laser diode.
Note the following.
Laser radiation when open. Do not stare into the beam, do not view directly
with optical instruments, and avoid direct exposure to the beam.
viii BladeCenter S Type 7779/8886: Installation and User's Guide

Class 1 Laser Product
Laser Klasse 1
Laser Klass 1
Luokan 1 Laserlaite
Appareil A Laser de Classe 1
`
Statement 8
CAUTION:
Never remove the cover on a power supply or any part that has the following
label attached.
Hazardous voltage, current, and energy levels are present inside any component
that has this label attached. There are no serviceable parts inside these
components. If you suspect a problem with one of these parts, contact a service
technician.
Statement 13
DANGER
Overloading a branch circuit is potentially a fire hazard and a shock hazard
under certain conditions. To avoid these hazards, ensure that your system
electrical requirements do not exceed branch circuit protection requirements.
Refer to the information that is provided with your device for electrical
specifications.
Statement 21
CAUTION:
Hazardous energy is present when the blade is connected to the power source.
Always replace the blade cover before installing the blade.
Safety ix

Statement 32
CAUTION:
To avoid personal injury, before lifting the unit, remove all the blades, power
supplies, and removable modules to reduce the weight.
108 kg
(237 lbs)
(2X)
(6X) (4X)
(4X)
43.2 kg
(95 lbs)
Statement 33
CAUTION:
This device does not provide a power control button. Removing power supply
modules or turning off the server blades does not turn off the electrical current
supplied to the device. The device also might have more than one power cord.
To remove all electrical current from the device, ensure that all power cords are
disconnected from the power source.
Rack Safety Information, Statement 2
DANGER
vAlways lower the leveling pads on the rack cabinet.
vAlways install stabilizer brackets on the rack cabinet.
vAlways install servers and optional devices starting from the bottom of the
rack cabinet.
vAlways install the heaviest devices in the bottom of the rack cabinet.
xBladeCenter S Type 7779/8886: Installation and User's Guide

Chapter 1. Introduction
The BladeCenter®S Type 8886 is a high-density, high-performance rack-mounted
server system. It supports up to six blade servers that can share common resources,
such as power, cooling, management, and I/O resources within a single
BladeCenter S chassis. In addition, it provides support for up to twelve 3.5-inch,
hot-swappable SAS or SATA hard disk drives.
The BladeCenter S system provides the following features:
vIBM Enterprise X-Architecture®Technology
IBM Enterprise X-Architecture Technology leverages proven innovative IBM
technologies to build powerful, scalable, and reliable blade servers. It provides
features such as IBM Predictive Failure Analysis (PFA) and real-time diagnostics.
vServer expansion capabilities
You can add up to six blade servers to the BladeCenter S chassis. Some blade
servers have connectors for additional optional devices that you can use to add
capabilities to the blade server. For example, you can connect either a storage
expansion unit or a PCI expansion unit to a blade server. Alternatively, you can
add optional I/O expansion cards to add network interfaces or storage through
I/O modules. SAS expansion cards provide access through SAS connectivity
modules or SAS RAID controller modules that are installed in I/O bays 3 and 4
to the hard disk drives in the BladeCenter S chassis.
Note: SAS connectivity modules support the use of SAS or SATA hard disk
drives. SAS RAID controller modules support the use of SAS hard disk drives
only.
vHot-swap capabilities
Bays in the BladeCenter S chassis are hot-swappable. For example, you can add,
remove, or replace a blade server or a SAS or SATA hard disk drive without
removing power from the BladeCenter S chassis.
The midplane provides hot-pluggable connectors for the following components:
– Six blade servers
– Four I/O modules
– One advanced management module
– One serial pass-thru module
– Four power modules
– Four fan modules
– Two storage modules
– One media tray
vHigh-availability design
Components in the BladeCenter S system enable continued operation if one of
the components fails:
–Power modules. In normal operation, the power modules provide power to
share the system load. If a power module fails, the working power modules
can continue to handle the entire load. You can replace a power module
without shutting down the BladeCenter S system.
© Copyright IBM Corp. 2007, 2010 1

Note: The power management policy that you have implemented for the
BladeCenter S system determines the result of a power module failure.
Power modules also provide cooling fans for the storage modules. Therefore,
if you are using storage module 1, you must install power modules 1 and 2. If
you are using storage module 2, you must install power modules 3 and 4.
–Fan modules. In normal operation, fan modules share the cooling in the
BladeCenter S system. If one fan module fails, the other three fan modules
handle the entire load. You can replace a fan module without shutting down
the BladeCenter S system.
–BladeCenter S system midplane. The midplane has the following
characteristics:
- Redundant high-speed serialize/deserialize (SERDES) interconnects
between blade servers and switches
- I2C communication between the advanced management module and all
modules (except blade servers)
- RS-485 (EIA 485) communication between the advanced management
module and blade servers
- Analog video connectors from the blade servers to the advanced
management module
- USB connections between the blade servers and the advanced management
module
–Redundant storage access. Installing a pair of SAS connectivity modules or
SAS RAID controller modules in I/O module bays 3 and 4 provides support
for redundant access to the storage modules in the BladeCenter S chassis (if
both storage modules are installed).
vSystems management
The advanced management module is used to communicate with the service
processor in each blade server to provide system monitoring, event recording,
and alerts. You can manage the BladeCenter S chassis, its devices, and the blade
servers remotely.
Related documentation
In addition to this document, the following related documentation is provided in
Portable Document Format (PDF) on the IBM BladeCenter Documentation CD that
comes with your BladeCenter S chassis.
Note: The latest and most up-to-date product information for the BladeCenter S
Types 7779 and 8886 can be found at the IBM Systems Information Center, which
is at http://publib.boulder.ibm.com/infocenter/systems/index.jsp. To access the
BladeCenter S system documentation from this site, click Systems hardware →
BladeCenter information →Chassis →BladeCenter S (8886).
In addition to the product documentation, online education is also available at this
location.
vBladeCenter S Types 7779 and 8886 Planning Guide
This document contains information to plan for the physical installation and
configuration of the BladeCenter S Types 7779 and 8886.
vBladeCenter S Types 7779 and 8886 Problem Determination and Service Guide
This document contains information for troubleshooting your BladeCenter S
system and solving problems.
vSerial over LAN Setup Guide
2BladeCenter S Type 7779/8886: Installation and User's Guide

This guide provides detailed Serial over LAN configuration information for your
BladeCenter S system.
vSafety Information
This document contains translated caution and danger statements. Each caution
and danger statement in the documentation has a number that you can use to
locate the corresponding statement in your language in the Safety Information
document.
vWarranty and Support
This document contains information about the terms of the warranty and getting
service and assistance.
Additional documentation might be included on the IBM BladeCenter Documentation
CD.
The BladeCenter S chassis might have features that are not described in the
documentation that comes with the BladeCenter S chassis. The documentation
might be updated occasionally to include information about those features, or
technical updates might be available to provide additional information that is not
included in the BladeCenter documentation. These updates are available from the
IBM Web site. To check for updated documentation, go to http://
publib.boulder.ibm.com/infocenter/bladectr/documentation/index.jsp.
The IBM BladeCenter Documentation CD
The IBM BladeCenter Documentation CD contains documentation for your
BladeCenter S chassis in Portable Document Format (PDF) and includes the IBM
Documentation Browser to help you find information quickly.
Hardware and software requirements
The IBM BladeCenter Documentation CD requires the following minimum hardware
and software:
vMicrosoft Windows NT XP, Windows 2000, or Red Hat Linux
v100 MHz microprocessor
v32 MB RAM
vAdobe Acrobat Reader 3.0 (or later) or xpdf, which comes with Linux operating
systems
Using the Documentation CD
Use the Documentation Browser to browse the contents of the CD, read brief
descriptions of the documents, and view documents, using Adobe Acrobat Reader
or xpdf. The Documentation Browser automatically detects the regional settings in
use in your system and presents the information in the language for that region (if
available). If a topic is not available in the language for that region, the
English-language version is displayed.
Use one of the following procedures to start the Documentation Browser:
vIf Autostart is enabled, insert the CD into the DVD drive. The Documentation
Browser starts automatically.
vIf Autostart is disabled or is not enabled for all users:
– If you are using a Windows operating system, insert the CD into the DVD
drive, and click Start →Run.IntheOpen field, type:
Chapter 1. Introduction 3

e:\win32.bat
where eis the drive letter of your DVD drive, and click OK.
– If you are using a Red Hat Linux, insert the CD into the DVD drive; then, run
the following command from the /mnt/cdrom directory:
sh runlinux.sh
Select your BladeCenter S chassis from the Product menu. The Available Topics
list displays all the documents for your BladeCenter product. Some documents
might be in folders. A plus sign (+) indicates each folder or document that has
additional topics under it. Click the plus sign to display the additional documents.
When you select a document, a description of the document appears under Topic
Description. To select more than one document, press and hold the Ctrl key while
you select the documents. Click View Book to view the selected document or
documents in Acrobat Reader or xpdf. If you selected more than one document, all
the selected documents are opened in Acrobat Reader or xpdf.
To search all the documents, type a word or word string in the Search field and
click Search. The documents in which the word or word string appears are listed
in order of the most occurrences. Click a document to view it, and press Ctrl+F to
use the Acrobat search function, or press Alt+F to use the xpdf search function
within the document.
Click Help for detailed information about using the Documentation Browser.
Notices and statements in this document
The caution and danger statements in this document are also in the multilingual
Safety Information document, which is on the IBM BladeCenter Documentation CD.
Each statement is numbered for reference to the corresponding statement in your
language in the Safety Information document.
The following notices and statements are used in this document:
vNote: These notices provide important tips, guidance, or advice.
vImportant: These notices provide information or advice that might help you
avoid inconvenient or problem situations.
vAttention: These notices indicate potential damage to programs, devices, or data.
An attention notice is placed just before the instruction or situation in which
damage might occur.
vCaution: These statements indicate situations that can be potentially hazardous
to you. A caution statement is placed just before the description of a potentially
hazardous procedure step or situation.
vDanger: These statements indicate situations that can be potentially lethal or
extremely hazardous to you. A danger statement is placed just before the
description of a potentially lethal or extremely hazardous procedure step or
situation.
4BladeCenter S Type 7779/8886: Installation and User's Guide

Features and specifications
The following table provides a summary of the features and specifications of the
BladeCenter S chassis.
Media tray (on front):
vOne DVD drive (can be either a
CD-RW/DVD-ROM or
DVD/RW drive)
vTwo USB v2.0 ports
vFront system LED panel
vTwo battery backup unit bay
locations, which support the SAS
RAID controller modules
Blade bays (on front): Six
hot-swap blade server bays
Storage module bays (on front):
Two storage bays, each containing
up to six 3.5-inch disk drive bays.
Module bays (on rear):
vOne hot-swap advanced
management module bay
vFour hot-swap power module
bays
vFour hot-swap fan module bays
vFour hot-swap I/O module bays
vOne hot-swap serial pass-thru
module bay
Power modules:
vMinimum: Two hot-swap power
modules.
vMaximum: Four hot-swap power
modules
Cooling:
Four variable-speed, hot-swap fan
modules
Two fans in each power supply
cool the storage modules
Management module:
vOne hot-swap advanced
management module
Upgradeable microcode:
vAdvanced management module
firmware
vI/O module firmware
vBlade server firmware
vStorage module firmware
Security features:
vLogin password for remote
connection
vSecure Sockets Layer (SSL) security
for remote management access
vLightweight Directory Access
Protocol (LDAP)
Predictive Failure Analysis (PFA)
alerts:
vFan modules
vBlade-dependent features
Size (7 U):
vHeight: 306.3 mm (12 in.)
vDepth: 733.4 mm (28.9 in.)
vWidth: 444 mm (17.5 in.)
vWeight:
– Fully configured weight with
blade servers: approximately
108.86 kg (240 lb)
– Empty chassis without modules
or blade servers: approximately
40.82 kg (90 lb)
Environment:
vAir temperature:
– BladeCenter S system on:
- Altitude: 0 to 914 m (3000 ft) 10°
to 35°C (50° to 95°F)
- Altitude: 914 m to 2134 m (3000
ft to 7000 ft) 10° to 32°C (50° to
90°F)
– BladeCenter S system off: -40° to
60°C (-40° to 140°F).
vHumidity: 8% to 80%
vAcoustics: declared sound power level:
6.3 to 6.8 bels
Electrical input:
vSine-wave input (50 - 60 Hz
single-phase) required
vInput voltage (110 V ac):
– Minimum: 100 Vrms
– Maximum: 127 Vrms
vInput voltage (220 V ac):
– Minimum: 200 Vrms
– Maximum: 240 Vrms
Heat output: Approximate heat output
in British thermal units (BTU) per hour:
vMinimum configuration: 1365 Btu per
hour (400 watts)
vMaximum configuration: 11942 Btu
per hour (3500 watts)
Chapter 1. Introduction 5

Components of the BladeCenter S system
BladeCenter S system components include an advanced management module,
blade servers, I/O modules, storage modules, power modules, fan modules, a
serial pass-thru module, and a media tray.
Front view of the BladeCenter S chassis
Blade servers, storage modules, and the media tray are installed in the front of the
BladeCenter S chassis.
Note: For proper cooling, each bay in the BladeCenter S chassis must have either a
device or a filler installed.
The following illustration shows the front of the BladeCenter S chassis.
Storage
module
1
Storage
module
2
SAS/SATA
hard disk drives
SAS/SATA
hard disk drives
Media tray
Blades
Battery backup
unit 1
Battery backup
unit 2
Storage modules
You can install a maximum of two storage modules in the BladeCenter S chassis
and each storage module contains hot-swap hard disk drives. A storage module
and the hard disk drives installed in that storage module are commonly referred to
as integrated shared storage because this storage is integrated in the BladeCenter S
chassis and shared among the blade servers in the BladeCenter S system.
Each storage module can support up to six hot-swap, 3.5-inch hard disk drives. If
you are installing SAS connectivity modules, both SAS and SATA hard disk drives
are supported, and you can use both types of hard disk drives in each storage
module. If you are installing SAS RAID controller modules, you must install SAS
hard disk drives.
Within each storage module, hard disk drives are numbered 1 through 6 from left
to right, and top to bottom.
Note: Each hard disk drive bay must contain either a hard disk drive or a
drive-bay filler.
6BladeCenter S Type 7779/8886: Installation and User's Guide

Note: Four power modules are required in the BladeCenter S chassis if both
storage modules are installed.
To access the hard disk drives in the storage module, the following devices must
be installed:
vSAS I/O modules. You can choose to install either SAS connectivity modules or
SAS RAID controller modules.
Note: You cannot mix these module types in the same BladeCenter S chassis.
– SAS connectivity module. At least one SAS connectivity module must be
installed. If a single SAS connectivity module is installed, it controls access to
both storage modules in the BladeCenter S chassis. If two SAS connectivity
modules are installed, the module in I/O module bay 3 controls access to
storage module 1, and the module in I/O module bay 4 controls access to
storage module 2.
– SAS RAID controller module. Two SAS RAID controller modules must be
installed, one in I/O module bay 3 and the other in I/O module bay 4. Each
SAS RAID controller module will have access to both storage modules (for
high availability).
vA SAS expansion card in each of the blade servers, which provides access
through the SAS I/O modules in I/O module bays 3 and 4 to the SAS or SATA
hard disk drives in each storage module.
There is one LED on each storage module:
Fault Solid (amber) when there is a storage module failure.
Chapter 1. Introduction 7

There are two LEDs on each hard disk drive:
Green Flashing when an operation, such as a read or a write, is being performed.
Amber
Flashing when the hard disk drive is being rebuilt (fast blink) or identified
(slow blink).
Note: When power is restored to the BladeCenter S chassis after a
complete loss of power and you have implemented the hard disk drives as
a mirrored array, the fault light will blink as the hard disk drive is being
resynchronized.
This resynchronization occurs because the blade servers are attempting to
power on before all of the storage modules and SAS connectivity modules
are powered up and available. The mirrored array is accessible during
resynchronization although performance may be slightly slower.
Solid when there is a drive failure.
8BladeCenter S Type 7779/8886: Installation and User's Guide