IBM e Server iSeries 825 User manual

iSeries 270, 800, 810, 820 or 825
Removable Media Device
Version 5
ERserver


iSeries 270, 800, 810, 820 or 825
Removable Media Device
Version 5
ER s e r v e r


Note
Before using this information and the product it supports, be sure to read the information in
“Notices,” on page 37.
Fourth Edition (August 2005)
This edition applies to version 5, release 3, modification 0of IBM Operating System/400
® (product number
5722–SS1) and to all subsequent releases and modifications until otherwise indicated in new editions. This version
does not run on all reduced instruction set computer (RISC) models nor does it run on CISC models.
©Copyright International Business Machines Corporation 2000, 2005. All rights reserved.
US Government Users Restricted Rights –Use, duplication or disclosure restricted by GSA ADP Schedule Contract
with IBM Corp.

Contents
Chapter 1. Removable media device ..1
Chapter 2. Before you begin ......3
Chapter 3. Replace removable media
devices in iSeries 270, 800, 810, or 820 .5
Chapter 4. Install removable media
devices in iSeries 270, 800, 810, or 820 .7
Details: Install removable media devices in iSeries
270, 800, 810, or 820 ............7
Completing the installation .........9
Chapter 5. Replace removable media
devices in iSeries 825 ........13
Replace removable media devices with 825 powered
on .................13
Replace removable media devices with 825 powered
off .................15
Chapter 6. Install removable media
devices in iSeries 825 ........19
Install removable media devices with 825 power on 20
Prepare to install aremovable media device ..20
Details: Install removable media devices with 825
powered on .............20
Install removable media devices with 825 powered
off .................22
Details: Install removable media devices with 825
power off ..............22
Chapter 7. Replace concurrent
removable media backplane .....25
Chapter 8. Install concurrent removable
media backplane ..........27
Details: Install concurrent removable media
backplane ...............28
Power down the system unit .....31
Unit Covers.............33
270, 800, 810 and 820 System Units ......33
270, 800, or 810 unit in arack .......35
Appendix. Notices ..........37
Trademarks ..............38
Terms and conditions for downloading and printing
publications ..............39
Code disclaimer information.........39
Electronic Emission Notices .........40
Federal Communications Commission (FCC)
statement ..............40
Electronic Emission Notices .........42
Federal Communications Commission (FCC)
statement ..............42
©Copyright IBM Corp. 2000, 2005 iii

iv 45xx, 46xx 270, 800, 810, 820, 825 Removable Media Device V5R3

Chapter 1. Removable media device
Replacing and installing this feature are customer tasks. When you use these instructions, you will
perform some or all of the following tasks:
vPerform prerequisite tasks.
vPower down the system unit.
vRemove the system unit covers.
vRemove hardware.
vInstall new hardware.
vInstall covers.
vIPL your operating system.
vVerify your new hardware configuration.
It will take approximately one hour to perform these tasks. You may need to allow additional time to
complete your jobs, back up your system, IPL your system, and verify your hardware configuration.
You can choose to perform these tasks yourself or contact IBM(R) or an authorized service provider to
make arrangements for them to perform the tasks for afee. Should you encounter difficulties when
performing atask, contact your authorized dealer or service provider.
Select the instructions for the task you want to perform:
vChapter 3, “Replace removable media devices in iSeries 270, 800, 810, or 820,” on page 5
vChapter 5, “Replace removable media devices in iSeries 825,” on page 13
vChapter 7, “Replace concurrent removable media backplane,” on page 25
vChapter 4, “Install removable media devices in iSeries 270, 800, 810, or 820,” on page 7
vChapter 6, “Install removable media devices in iSeries 825,” on page 19
vChapter 8, “Install concurrent removable media backplane,” on page 27
©Copyright IBM Corp. 2000, 2005 1

245xx, 46xx 270, 800, 810, 820, 825 Removable Media Device V5R3

Chapter 2. Before you begin
Before you begin areplacement or installation task, follow these steps:
__ 1. For an installation and if possible, for areplacement, ensure that you have acurrent backup of
your system (including operating system, licensed programs, and data). If you have backed up
the operating system and licensed programs since the last time you applied PTFs, that backup is
acceptable.
__ 2. Ensure that you take afew minutes to become familiar with these instructions.
__ 3. Ensure that you have access to amedium flat-bladed screwdriver.
__ 4. If there are incorrect, missing, or visibly damaged parts, contact one of the following:
vYour authorized service provider
vIn the United States: IBM
® Rochester Manufacturing Automated Information Line (R–MAIL) at
1–800–300–8751
vIn countries outside of the United States: Use the following Web site to locate your service and
support numbers:
http://www.ibm.com/planetwide
__ 5. If you are installing new hardware in logical partitions, you need to plan and understand the
requirements to be successful. Go to Logical partitions in the Information Center.Then return to
these instructions.
__ 6. If you encounter difficulties during the procedure, contact your authorized service provider or
your authorized dealer.
__ 7. Determine if there are any existing PTF prerequisites before you install your new feature. Go to the
following Web site:
http://www-912.ibm.com/s_dir/slkbase.NSF/slkbase
a. Select All Documents.
b. Select General Information.
c. Select Offerings.
d. Select Feature Prerequisites.
e. Select Customer Installation Features Prerequisites.
f. Locate your feature number and OS/400
® release, and check the prerequisites.
©Copyright IBM Corp. 2000, 2005 3

445xx, 46xx 270, 800, 810, 820, 825 Removable Media Device V5R3