IBM System x iDataPlex dx360 User manual

System xiDataPlex dx360 FAQ for
Ty pes 6313, 6316, 6385, 6390, 7831, and 7833
Hints and Tips


System xiDataPlex dx360 FAQ for
Ty pes 6313, 6316, 6385, 6390, 7831, and 7833
Hints and Tips


Note: Before using this information and the product it supports, read the general information in “Notices,” on page 13.
First Edition (November 2008)
©Copyright International Business Machines Corporation 2008.
US Government Users Restricted Rights –Use, duplication or disclosure restricted by GSA ADP Schedule Contract
with IBM Corp.

Contents
Chapter 1. Introduction ......................1
Related documentation ......................1
Getting updated documentation ...................2
Features and specifications .....................2
Operator panel controls, LEDs, and connectors .............3
System-board tray components ...................4
Chapter 2. Hints and tips .....................5
Boot order ...........................5
Diagnostic programs .......................6
Firmware updates ........................6
Hardware configuration ......................7
IP settings and alerts .......................7
Management tools ........................8
Memory ............................8
Microprocessors .........................9
Operating systems ........................9
Passwords and security ......................9
System-error LED ........................10
Video ............................10
Chapter 3. Getting help and technical assistance ...........11
Before you call .........................11
Using the documentation .....................11
Getting help and information from the World Wide Web ..........11
Software service and support ...................12
Hardware service and support ...................12
IBM Taiwan product service ....................12
Appendix. Notices .......................13
Trademarks ..........................14
Important notes.........................15
Index ............................17
©Copyright IBM Corp. 2008 iii

iv IBM System xiDataPlex dx360 Hints and Tips

Chapter 1. Introduction
This document is intended to supplement the documentation provided with the IBM®
System x™iDataPlex™dx360. It contains answers to some frequently asked
questions about the components in the customized iDataPlex server solutions. For
the iDataPlex dx360 servers, these components consist of the IBM System x
iDataPlex dx360 Type 6316, 6390, or 7833 system-board tray, the IBM System x
iDataPlex Types 6313, 6385, or 7831 2U flex chassis, and the IBM System x
iDataPlex storage enclosure.
With the exception of the warranty period, the iDataPlex products are functionally
equivalent as follows:
vIBM System xiDataPlex dx360 system-board tray Types 6316, 6390, and 7833
are functionally equivalent
vIBM System xiDataPlex 2U flex chassis Types 6313, 6385, and 7831 are
functionally equivalent
For specific information about the warranty type or warranty duration, see the IBM
Machine Types 6313, 6316, 6385, 6386, 6388, 6389, 6390, 7825, 7831, 7832,
7833, 7834, and the Rear Door Heat eXchanger for the iDataPlex Rack Warranty
and Support Information document.
Related documentation
The following documentation is available for the IBM System xiDataPlex dx360
hardware configurations:
vIBM System xiDataPlex dx360 Types 6313, 6316, 6385, 6390, 7831, and 7833
User's Guide
This document contains general information about how to use, upgrade, and
configure the 2U chassis, the dx360 system-board tray, and the System x
iDataPlex storage enclosure.
vIBM System xiDataPlex dx360 Types 6313, 6316, 6385, 6390, 7831, and 7833
Problem Determination and Service Guide
This document contains information to help you solve problems yourself and
information for service technicians. It contains information about the POST beep
codes, error messages, and error logs; basic and advanced checkout
procedures; troubleshooting tables; and Dynamic System Analysis (DSA) Preboot
diagnostic programs.
vIBM iDataPlex Rack Type 7825 Installation and User's Guide
This document provides general information about the iDataPlex rack, including
information about planning and how to get help.
vIBM Rear Door Heat eXchanger for the iDataPlex Rack Installation and
Maintenance Guide
This document contains instructions and additional information for installing,
setting up, and maintaining the IBM Rear Door Heat eXchanger for the iDataPlex
Rack. Only professional movers, installers, or trained personnel may move,
install, replace, remove, or transport the heat exchanger.
vIBM System xiDataPlex Warranty and Support Information
This document contains information about the terms of the warranty and getting
service and assistance.
©Copyright IBM Corp. 2008 1

vIBM Safety Information
This document contains translated caution and danger statements. Each caution
and danger statement that appears in the documentation has anumber that you
can use to locate the corresponding statement in your language in the Safety
Information document.
vRack Safety Information
This document contains translated caution and danger statements. Each caution
and danger statement that appears in the documentation has anumber that you
can use to locate the corresponding statement in your language in the Rack
Safety Information document.
Getting updated documentation
The iDataPlex documentation might be updated occasionally, or technical updates
might be available to provide additional information that is not included in the
documentation. These updates are available from the IBM Systems Information
Center. To check for updated iDataPlex information and technical updates, go to
http://publib.boulder.ibm.com/infocenter/systems/scope/idataplex/index.jsp .
The updated iDataPlex documentation also is available from the IBM Support Web
site. To check for updated documentation and technical updates, complete the
following steps.
Note: Changes are made periodically to the IBM Web site. The actual procedure
might vary slightly from what is described in this document.
1. Go to http://www.ibm.com/systems/support/.
2. Under Product support,click System x.
3. Under Popular links,click Publications lookup.
4. From the Product family menu, select System xiDataPlex dx360 server and
click Go.
Features and specifications
The following information is asummary of the features and specifications of the
iDataPlex dx360 hardware. Depending on the hardware configuration, some
features might not be available, or some specifications might not apply.
Racks are marked in vertical increments of 4.45 cm (1.75 inches). Each increment
is referred to as aunit, or “U.” A1U-high device is 1.75 inches tall.
2IBM System xiDataPlex dx360 Hints and Tips

Table 1. Features and specifications
Microprocessor: Supports two
dual-core or quad-core Intel®Xeon™
microprocessors in each system-board
tray
Note: Use the BIOS Setup Utility
program to determine the type and
speed of the microprocessor.
Memory:
vFour-channel DIMMs: 16 DIMM
connectors
vTypes: Fully buffered double-data
rate (DDR2) 667 MHz DIMMs with
AMB+ or DDR2 800 MHz DIMMs
with AMB+
vSupports 2GB and 4GB DIMMs
(as of the date of this publication)
with up to 64 GB of total memory in
each system-board tray
Hard disk drives:
vThe system-board tray supports
one 3.5-inch simple-swap SAS or
one 3.5-inch simple-swap SATA
hard disk drive.
vThe system-board tray with a
storage enclosure attached can
support up to four 3.5-inch
simple-swap SAS hard disk drives
or up to five 3.5-inch simple-swap
SATA hard disk drives.
PCI expansion slots:
vEach system-board tray supports
one PCIe expansion slot
Integrated functions:
vIntel baseboard management
controller (BMC) with Intelligent
Platform Management Interface
(IPMI) 2.0 compliant firmware
vATI ES1000 video controller with
32 MB DDR2 SDRAM
vDual 10 Mb/100 Mb/1 GB network
interface controllers
vWake on LAN®support
vI/O Controller with six Serial ATA
(SATA) ports
vFront panel connectors:
–Two Universal Serial Bus
(USB) 2.0 ports
–One systems management
serial port
–VGA video port
–Two Ethernet ports
Size (2U chassis):
vHeight: 86 mm (3.386 inches)
vDepth: 473 mm (18.6 inches)
vWidth: 446 mm (17.56 inches)
vMaximum weight: 6.98 kg (15.5 lb)
Environment:
vAir temperature:
–Server on: 10°C to 35°C (50°F to
95°F); altitude: 0to 914.4 m(0 to
3000 ft). Derate maximum
temperature by 1°C for every
304.8 m(1000 ft) increase in
elevation to amaximum of
3,048.0 m(10000 ft) at an
ambient temperature of 28°C.
–Server off: 10°C to 43°C (59°F to
109.4°F); maximum altitude: 2133
m(7000 ft)
v
Humidity:
–Server on: 10% to 80%
–Server off: 8% to 80%
Electrical Input:
vInput voltage low range: 100 Vac
(minimum) to 127 Vac (maximum),
50 to 60 Hz, sine-wave input
vInput voltage high range: 200 Vac
(minimum) to 240 Vac (maximum),
50 to 60 Hz, sine-wave input
Operator panel controls, LEDs, and connectors
The following illustration shows the controls, LEDs, and connectors on the front of
the dx360 system-board tray. The operator panel on the system-board tray is the
same for all dx360 server configurations.
Chapter 1. Introduction 3

System-board tray components
The following illustration shows the major components in the dx360 system-board
tray.
Note: The illustrations in this document might differ slightly from your hardware.
4IBM System xiDataPlex dx360 Hints and Tips

Chapter 2. Hints and tips
This chapter contains answers to some frequently asked questions about the
iDataPlex dx360 servers. The topics are arranged alphabetically so that you can
find the information easily. This information is intended to supplement the iDataPlex
documentation listed in “Related documentation” on page 1.
Boot order
vWhat is the iDataPlex dx360 boot order?
As shipped, the boot order for the iDataPlex dx360 server is set as follows:
1. Network boot
2. Hard disk drive boot
3. Unified Extensible Firmware Interface (UEFI) boot
v
What is the factory default iDataPlex dx360 boot order?
If you reset the boot order for the iDataPlex dx360 server to its factory default
setting, the boot order reverts to the manufacturer's setting, which is as follows:
1. Hard disk drive boot
2. Network boot
3. Unified Extensible Firmware Interface (UEFI) boot
v
How can Ichange the iDataPlex dx360 boot order?
You can use the BIOS Setup Utility to change or temporarily override the boot
order settings. To use the BIOS Setup Utility to change or override the boot order
settings, complete the following steps:
1. Turn off the system-board tray.
2. Restart the system-board tray.
3. Press F2.
4. Select one of the following:
–Boot Options
Select this choice to view or permanently change the boot order settings
in BIOS.
–Boot Manager
Select this choice to temporarily override the boot order settings in BIOS
without changing the settings in the BIOS Configuration Utility. The next
time the system-board tray is started, it returns to the startup sequence
that is set in the BIOS Configuration Utility program.
5. Select the startup device and press Enter to boot from the selected device.
©Copyright IBM Corp. 2008 5

Diagnostic programs
vDoes the iDataPlex dx360 support the IBM Dynamic System Analysis (DSA)
Preboot programs?
The IBM Dynamic System Analysis (DSA) Preboot diagnostic programs are the
primary method of testing the major components of the iDataPlex servers. There
are some limitations to the number of DSA Preboot tests supported for the
iDataPlex dx360.
vHow can Iobtain acurrent image of the DSA Preboot diagnostic programs?
To download the latest version of the DSA Preboot programs, complete the
following steps.
Note: Changes are made periodically to the IBM Web site. The actual procedure
might vary slightly from what is described in this document.
1. Go to http://www.ibm.com/systems/support/.
2. Under Product support,click System x.
3. Under Popular links,click Software and device drivers.
4. Click Dynamic System Analysis (DSA).
For additional information about using the DSA diagnostic programs, see the IBM
System xiDataPlex dx360 Problem Determination and Service Guide.
Firmware updates
vCan Iupdate just the BIOS?
The firmware-update package contains the BIOS and BMC code. When you
install the package, it automatically updates the BIOS and BMC code
simultaneously. To view the current firmware levels, you can use the DSA
Preboot program, or you can press F2 during startup to enter the BIOS Setup
utility.
vHow can Iobtain the current firmware-update package?
To download the latest firmware package for the iDataPlex dx360, complete the
following steps.
Note: Changes are made periodically to the IBM Web site. The actual procedure
might vary slightly from what is described in this document.
1. Go to http://www.ibm.com/systems/support/.
2. Under Product support,click System x.
3. Under Popular links,click Software and device drivers.
4. Click System xiDataPlex dx360 server to display the matrix of
downloadable files.
5. Select the applicable file for your operating system and the file type for the
medium that you want to use; then, download the flash update.
For additional information about updating the firmware, see the IBM System x
iDataPlex dx360 Problem Determination and Service Guide.
6IBM System xiDataPlex dx360 Hints and Tips

Hardware configuration
vCan Imix iDataPlex dx320, dx340, and dx360 servers in the same rack?
To avoid potential problems, do not change the mixture of servers installed in a
configured iDataPlex rack solution.
As of the date of this publication, no iDataPlex rack solutions are available with a
mixture of dx320, dx340, and dx360 servers. For up-to-date information about
iDataPlex rack solutions that contain multiple types of servers, contact your IBM
marketing representative or authorized reseller.
vWhat iDataPlex dx360 server configurations are available?
Two basic server configurations are available as follows:
–The 2U compute server consists of two identical iDataPlex dx360
system-board trays installed in a2U chassis. The system-board trays function
as two independent 1U servers. Each iDataPlex dx360 system-board tray
supports one 3.5-inch simple-swap hard disk drive.
–The 2U storage server consists of adx360 system-board tray with astorage
enclosure installed in a2U chassis. The storage enclosure provides four
additional 3.5-inch drive bays and enables the server to have up to four
3.5-inch simple-swap SAS hard disk drives or up to five 3.5-inch simple-swap
SATA hard disk drives.
Note: The drive bay in the system-board tray is not used when the storage
enclosure contains 3.5-inch simple-swap SAS drives.
IP settings and alerts
vWhere are the BMC IP settings for the dx360 system-board tray?
You must issue IPMI commands to obtain the baseboard management controller
(BMC) IP settings. Instructions for obtaining the BMC IP settings are provided in
Retain Tip 9693.
vWhy can't Iget Alerts from the iDataPlex dx360 system-board tray during
the Address Resolution Protocol (ARP) process?
To receive Alerts during the ARP process, you must enter both the media access
control (MAC) address and the IP address of the target device.
Note: The BMC MAC address is on alabel that is to the left of the PCIe slot on
the front of the dx360 system-board tray.
Chapter 2. Hints and tips 7

Management tools
vWhat management tools are available for the iDataPlex dx360?
The following tools have been tested and approved for use with the iDataPlex
dx360:
–Avocent 5300
–IPMItool (available at http://ipmitool.sourceforge.net/)
–Extreme Cluster Administration Toolkit (XCAT) (available at
http://xcat.sourceforge.net/)
vIs there autility program that Ican use to set all of the configuration
parameters for all of the dx360 servers in my iDataPlex rack?
As of the date of this publication, the only utilities that are available to set all of
the configuration parameters are the Intel sysconfig utilities. The sysconfig
utilities are provided and supported by Intel, and you can download the utilities
from the following sites:
–Save and Restore System Configuration Utility for Linux:
http://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&inst=yes
&productid=2859&dwnldid=16919&stross=all&osfullname=all%20operating
%20systems&lang=eng
–Save and Restore System Configuration Utility for the EFI Shell:
http://downloadcenter.intel.com/Detail_Desc.aspx?agr=Y&inst=yes
&productid=2859&dwnldid=16923&stross=all&osfullname=all%20operating
%20systems&lang=eng
Memory
vAre memory upgrades available for the iDataPlex dx360?
Memory upgrades are not available for the iDataPlex dx360 servers. To avoid
potential problems, do not attempt to upgrade the number or type of DIMMs in an
iDataPlex dx360 system-board tray.
vWhat type of memory is available for the iDataPlex dx360?
The iDataPlex dx360 system board has 16 DIMM connectors and supports fully
buffered double-data rate (DDR2) 667 MHz DIMMs with AMB+ or DDR2 800
MHz DIMMs with AMB+. As of the date of this publication, the dx360 supports
the following 2GB and 4GB DIMMs with up to 64 GB of total memory in each
system-board tray.
2GB DIMM, DDR2–667 PC2-5300 555 fully buffered DIMM with AMB+
4GB DIMM, DDR2–667 PC2-5300 555 fully buffered DIMM with AMB+
2GB DIMM, DDR2–800 PC2-6400 666 fully buffered DIMM with AMB+
4GB DIMM, DDR2–800 PC2-6400 666 fully buffered DIMM with AMB+
Notes:
1. The 667 MHz DIMMs operate with all supported microprocessors. (See
“Microprocessors” on page 9for the list of supported microprocessors.)
2. The 800 MHz DIMMs operate with only the Intel Xeon E5462 2.80 GHz/1600
MHz quad core and Intel Xeon E5472 3.00 GHz/1600 MHz quad core
microprocessors.
8IBM System xiDataPlex dx360 Hints and Tips

Microprocessors
vAre microprocessor upgrades available for the iDataPlex dx360?
Microprocessor upgrades are not available for the iDataPlex dx360 servers. The
microprocessors are field replaceable units (FRUs). FRUs must be installed,
removed, or replaced only by trained service technicians.
vWhat microprocessors are available for the iDataPlex dx360?
The iDataPlex dx360 system board supports two dual-core or quad-core Intel
Xeon microprocessors. As of the date of this publication, the following
microprocessors are available for the iDataPlex dx360 system board:
Intel Xeon L5410 2.33 GHz/1333 MHz quad core 50W
Intel Xeon L5420 2.50 GHz/1333 MHz quad core 50W
Intel Xeon E5420 2.50 GHz/1333 MHz quad core 80W
Intel Xeon E5430 2.66 GHz/1333 MHz quad core 80W
Intel Xeon E5462 2.80 GHz/1600 MHz quad core 80W
Intel Xeon E5440 2.83 GHz/1333 MHz quad core 80W
Intel Xeon L5240 3.00 GHz/1333 MHz dual core 40W
Intel Xeon E5472 3.00 GHz/1600 MHz quad core 80W
Operating systems
What operating systems are supported for the iDataPlex dx360?
As of the date of this publication, the iDataPlex dx360 servers support Red Hat
Enterprise Linux®5.1 and SUSE Linux Enterprise Server (SLES) 10.1. For
up-to-date information about the operating systems supported for the iDataPlex
dx360, contact your IBM marketing representative or authorized reseller.
Passwords and security
vWhy did the iDataPlex dx360 server stop working and display the message
Invalid Password?
The iDataPlex dx360 server will stop operating when an incorrect power-on
password is entered three consecutive times. You can regain access to the
dx360 server in any of the following ways:
–If an administrator password is set, type the administrator password at the
password prompt. Start the BIOS Setup Utility program and reset the user
password.
–Clear the password by using the clear jumper. (See the IBM System x
iDataPlex dx360 Problem Determination and Service Guide for instructions.)
vWhy are all users allowed to connect to the iDataPlex dx360 with an IPMI
command?
The iDataPlex dx360 is shipped with no configured password. When the
iDataPlex dx360 is installed, the customer must set the password and
authentication level if they want to restrict access to the server.
Chapter 2. Hints and tips 9

System-error LED
Why is the system-error LED on the iDataPlex dx360 system-board tray lit
when there are no other error indications?
If the system-error LED on the front of the system-board tray is lit but there are
no error indications, clear the BMC system-event log. This log does not clear
itself, and if it begins to fill up, the system-error LED will be lit. Also, after you
complete arepair or correct an error, clear the BMC system-event log to turn off
the system-error LED.
Video
Why does the video take so long to appear during startup?
During startup, the iDataPlex dx360 BIOS Power on Self-Test (POST) verifies
the memory and all hardware subsystems. The last step in the BIOS POST
process is the video display initialization. BIOS requires approximately 40
seconds to complete the POST process and initialize the video display.
10 IBM System xiDataPlex dx360 Hints and Tips

Chapter 3. Getting help and technical assistance
If you need help, service, or technical assistance or just want more information
about IBM products, you will find awide variety of sources available from IBM to
assist you. This section contains information about where to go for additional
information about IBM and IBM products, what to do if you experience aproblem
with your system, and whom to call for service, if it is necessary.
Before you call
Before you call, make sure that you have taken these steps to try to solve the
problem yourself:
vCheck all cables to make sure that they are connected.
vCheck the power switches to make sure that the system and any optional
devices are turned on.
vUse the troubleshooting information in your system documentation, and use the
diagnostic tools that come with your system. Information about diagnostic tools is
in the Problem Determination and Service Guide on the IBM Documentation CD
that comes with your system.
vGo to the IBM support Web site at http://www.ibm.com/systems/support/ to check
for technical information, hints, tips, and new device drivers or to submit a
request for information.
You can solve many problems without outside assistance by following the
troubleshooting procedures that IBM provides in the online help or in the
documentation that is provided with your IBM product. The documentation that
comes with IBM systems also describes the diagnostic tests that you can perform.
Most systems, operating systems, and programs come with documentation that
contains troubleshooting procedures and explanations of error messages and error
codes. If you suspect asoftware problem, see the documentation for the operating
system or program.
Using the documentation
Information about your IBM system and preinstalled software, if any, or optional
device is available in the documentation that comes with the product. That
documentation can include printed documents, online documents, readme files, and
help files. See the troubleshooting information in your system documentation for
instructions for using the diagnostic programs. The troubleshooting information or
the diagnostic programs might tell you that you need additional or updated device
drivers or other software. IBM maintains pages on the World Wide Web where you
can get the latest technical information and download device drivers and updates.
To access these pages, go to http://www.ibm.com/systems/support/ and follow the
instructions. Also, some documents are available through the IBM Publications
Center at http://www.ibm.com/shop/publications/order/.
Getting help and information from the World Wide Web
On the World Wide Web, the IBM Web site has up-to-date information about IBM
systems, optional devices, services, and support. The address for IBM System x
and xSeries®information is http://www.ibm.com/systems/x/.
©Copyright IBM Corp. 2008 11

The address for IBM iDataPlex information is http://publib.boulder.ibm.com/
infocenter/systems/scope/idataplex/index.jsp. The address for IBM BladeCenter®
information is http://www.ibm.com/systems/bladecenter/. The address for IBM
IntelliStation®information is http://www.ibm.com/intellistation/.
You can find service information for IBM systems and optional devices at
http://www.ibm.com/systems/support/.
Software service and support
Through IBM Support Line, you can get telephone assistance, for afee, with usage,
configuration, and software problems with System xand xSeries servers,
BladeCenter products, IntelliStation workstations, and appliances. For information
about which products are supported by Support Line in your country or region, see
http://www.ibm.com/services/sl/products/.
For more information about Support Line and other IBM services, see
http://www.ibm.com/services/, or see http://www.ibm.com/planetwide/ for support
telephone numbers. In the U.S. and Canada, call 1-800-IBM-SERV
(1-800-426-7378).
Hardware service and support
You can receive hardware service through IBM Services or through your IBM
reseller, if your reseller is authorized by IBM to provide warranty service. See
http://www.ibm.com/planetwide/ for support telephone numbers, or in the U.S. and
Canada, call 1-800-IBM-SERV (1-800-426-7378).
In the U.S. and Canada, hardware service and support is available 24 hours aday,
7days aweek. In the U.K., these services are available Monday through Friday,
from 9a.m. to 6p.m.
IBM Taiwan product service
IBM Taiwan product service contact information:
IBM Taiwan Corporation
3F, No 7, Song Ren Rd.
Taipei, Taiwan
Telephone: [phone]
12 IBM System xiDataPlex dx360 Hints and Tips

Appendix. Notices
This information was developed for products and services offered in the U.S.A.
IBM may not offer the products, services, or features discussed in this document in
other countries. Consult your local IBM representative for information on the
products and services currently available in your area. Any reference to an IBM
product, program, or service is not intended to state or imply that only that IBM
product, program, or service may be used. Any functionally equivalent product,
program, or service that does not infringe any IBM intellectual property right may be
used instead. However, it is the user’s responsibility to evaluate and verify the
operation of any non-IBM product, program, or service.
IBM may have patents or pending patent applications covering subject matter
described in this document. The furnishing of this document does not give you any
license to these patents. You can send license inquiries, in writing, to:
IBM Director of Licensing
IBM Corporation
North Castle Drive
Armonk, NY 10504-1785
U.S.A.
INTERNATIONAL BUSINESS MACHINES CORPORATION PROVIDES THIS
PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
OF NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. Some states do not allow disclaimer of express or
implied warranties in certain transactions, therefore, this statement may not apply to
you.
This information could include technical inaccuracies or typographical errors.
Changes are periodically made to the information herein; these changes will be
incorporated in new editions of the publication. IBM may make improvements and/or
changes in the product(s) and/or the program(s) described in this publication at any
time without notice.
Any references in this information to non-IBM Web sites are provided for
convenience only and do not in any manner serve as an endorsement of those
Web sites. The materials at those Web sites are not part of the materials for this
IBM product, and use of those Web sites is at your own risk.
IBM may use or distribute any of the information you supply in any way it believes
appropriate without incurring any obligation to you.
©Copyright IBM Corp. 2008 13

Trademarks
The following terms are trademarks of International Business Machines Corporation
in the United States, other countries, or both:
BladeCenter iDataPlex System x
IBM IntelliStation Wake on LAN
IBM (logo) ServerProven xSeries
Intel, Intel Xeon, Itanium, and Pentium are trademarks or registered trademarks of
Intel Corporation in the United States, other countries, or both.
Microsoft, Windows, and Windows NT are trademarks of Microsoft Corporation in
the United States, other countries, or both.
Adobe and PostScript are either registered trademarks or trademarks of Adobe
Systems Incorporated in the United States, other countries, or both.
UNIX is aregistered trademark of The Open Group in the United States and other
countries.
Java and all Java-based trademarks are trademarks of Sun Microsystems, Inc. in
the United States, other countries, or both.
Adaptec and HostRAID are trademarks of Adaptec, Inc., in the United States, other
countries, or both.
Linux is aregistered trademark of Linus Torvalds in the United States, other
countries, or both.
Red Hat, the Red Hat “Shadow Man” logo, and all Red Hat-based trademarks and
logos are trademarks or registered trademarks of Red Hat, Inc., in the United States
and other countries.
Other company, product, or service names may be trademarks or service marks of
others.
14 IBM System xiDataPlex dx360 Hints and Tips