IBM Cloud Object Storage System Slicestor 2212... User manual

IBM Cloud Object Storage System
Version 3.14.2
Slicestor 2212 Appliance Manual
3409-S00/3401-S00/3403-S00
IBM

Note
Before using this information and the product it supports, read the following information:
vThe general information in Notices
vThe information in Safety and environmental notices
vThe information in the IBM Environmental Notices and User Guide (provided on a DVD)
This edition applies to IBM Cloud Object Storage System™and is valid until replaced by new editions.
© Copyright IBM Corporation 2016, ..
US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract
with IBM Corp.

Contents
Figures ............... v
Tables ............... vii
Document information ........ ix
Safety and environmental notices ... xi
Safety notices .............. xi
Environmental notices .......... xiv
Declared noise emissions ......... xv
Support information ........ xvii
Chapter 1. Slicestor 2212
ApplianceManual ........... 1
Chapter 2. Appliance safety precautions 3
Physical ................ 3
Electrical................ 3
Electronic components ........... 4
Chapter 3. Specifications and
requirements ............ 5
Appliance specifications .......... 5
Requirements .............. 5
System diagram ............. 6
Chapter 4. Install the appliance into a
rack ................ 7
Prepare for installation ........... 7
Appliance installation ........... 9
Chapter 5. Appliance physical interface 15
Front control panel ............ 15
Rear panel............... 16
Chapter 6. Field replaceable or upgrade
units................ 19
Replacement parts ............ 19
Replace external front components ...... 19
Replace external rear components ....... 24
Battery removal and installation ....... 25
Notices .............. 27
Trademarks .............. 29
Homologation statement .......... 29
© Copyright IBM Corp. 2016, . iii

iv IBM Cloud Object Storage System: Slicestor 2212 Appliance Manual 3409-S00/3401-S00/3403-S00

Figures
1. System diagram ........... 6
2. Drive layout ............ 6
3. 2×M5×20 mm round head screws ..... 8
4. 8×M5×8 mm flat head screws ....... 8
5. 4×M4×4 mm flat head screws ....... 8
6. 8×Cone washers for M5 ......... 9
7. 2×C13-to-C14 connector, 6 ft, 14 AWG power
cables ............... 9
8. 2×Rack rails ............. 9
9. Identifying rail parts .......... 9
10. Extend and release inner rail....... 10
11. Installing the inner rails ........ 11
12. Inner rails installed on appliance ..... 11
13. Extending and releasing the outer rails ... 11
14. Securing the outer rail to the rack with screws 12
15. Extending the outer rail to reach the rear posts
of the rack ............. 12
16. Ball-bearing shuttle in the middle rail .... 13
17. If necessary, secure the appliance handles to
front of rack with screws ........ 13
18. Rear of appliance .......... 14
19. Front of appliance .......... 14
20. Front panel buttons and LEDs for the
appliance ............. 15
21. Rear panel I/O ports for the appliance 16
22. LAN LED connection speed indicator .... 17
23. Extending the handle for a drive from the
chassis .............. 20
24. Removing a drive from the chassis..... 21
25. Extending the handle for a drive from the
chassis .............. 22
26. Removing a drive from the chassis..... 23
27. Removing a PSU from the chassis ..... 25
28. Remove the battery .......... 26
29. Install the battery .......... 26
© Copyright IBM Corp. 2016, . v

vi IBM Cloud Object Storage System: Slicestor 2212 Appliance Manual 3409-S00/3401-S00/3403-S00

Tables
1. Declared noise emissions in accordance with
ISO 9296(1,2,3) ............ xv
2. System components in the appliance .... 5
3. Space and power requirements for the
appliance.............. 5
4. Operating and non-operating temperatures and
humidity for the appliance ........ 5
5. Cabling requirements for the appliance.... 5
6. Appliance location considerations ..... 7
7. Legend for rear panel I/O Ports for the
appliance ............. 16
8. LAN LED connection speed colors ..... 17
9. Power supply LED states ........ 17
10. Conditions indicated by drive carrier LEDs 17
11. Descriptions for the ports represented by this
appliance ............. 18
© Copyright IBM Corp. 2016, . vii

viii IBM Cloud Object Storage System: Slicestor 2212 Appliance Manual 3409-S00/3401-S00/3403-S00

Document information
Intended purpose and audience
This manual contains the instructions for installing and maintaining this appliance. The audience for this
guide consists of those individuals responsible for installing IBM Cloud Object Storage System™
appliances.
Note:
vThe equipment and device described for installation herein are sophisticated and relatively complex to
install. The party or parties installing the equipment must be familiar with installations of computer
hardware and disk drives prior to attempting this installation. Only personnel proficient in working
with computer hardware and disk drives should attempt to install this appliance.
vAfter all appliances have been installed in the rack, refer to the Appliance Configuration Guide to
configure the appliance settings required prior to setting up the system.
vAfter these appliances are configured, refer to the System Manager Administration Guide for information
about how to configure, operate, and maintain your system.
vBoth the Appliance Configuration Guide and the System Manager Administration Guide assume that all
necessary appliances for the system are installed in the rack.
© Copyright IBM Corp. 2016, . ix

xIBM Cloud Object Storage System: Slicestor 2212 Appliance Manual 3409-S00/3401-S00/3403-S00

Safety and environmental notices
Review the safety notices, environmental notices, and electronic emission notices for IBM®Cloud Object
Storage System before you install and use the product.
Suitability for telecommunication environment - This product is not intended to connect directly or
indirectly by any means whatsoever to interfaces of public telecommunications networks.
Examples of a caution and a danger notice. Numbers in parentheses refer to message numbers in the IBM
Safety Notices publication G229-9054, which is included with your product.
CAUTION:
A caution notice indicates the presence of a hazard that has the potential of causing moderate or
minor personal injury. (C001)
DANGER
A danger notice indicates the presence of a hazard that has the potential of causing death or serious
personal injury. (D002)
Safety notices
Safety notices for this product.
Familiarize yourself with the IBM Safety Notices publication G229-9054, which is included with your
product.
© Copyright IBM Corp. 2016, . xi

DANGER: When working on or around the system, observe the following precautions:
Electrical voltage and current from power, telephone, and communication cables are hazardous. To
avoid a shock hazard:
• , connect power to this unit only with the IBM provided powerIf IBM supplied a power cord(s)
cord. Do not use the IBM provided power cord for any other product.
• Do not open or service any power supply assembly.
• Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration
of this product during an electrical storm.
• The product might be equipped with multiple power cords. To remove all hazardous voltages,
disconnect all power cords.
• Connect all power cords to a properly wired and grounded electrical outlet. Ensure that the outlet
supplies proper voltage and phase rotation according to the system rating plate.
• Connect any equipment that will be attached to this product to properly wired outlets.
• When possible, use one hand only to connect or disconnect signal cables.
• Never turn on any equipment when there is evidence of fire, water, or structural damage.
• Do not attempt to switch on power to the machine until all possible unsafe conditions are corrected.
• Assume that an electrical safety hazard is present. Perform all continuity, grounding, and power
checks specified during the subsystem installation procedures to ensure that the machine meets
safety requirements.
• Do not continue with the inspection if any unsafe conditions are present.
• Disconnect the attached power cords, telecommunications systems, networks, and modems before
you open the device covers, unless instructed otherwise in the installation and configuration
procedures.
• Connect and disconnect cables as described in the following procedures when installing, moving,
or opening covers on this product or attached devices.
To disconnect:
1. Turn off everything (unless instructed otherwise).
2. Remove the power cords from the outlets.
3. Remove the signal cables from the connectors.
4. Remove all cables from the devices.
To connect:
1. Turn off everything (unless instructed otherwise).
2. Attach all cables to the devices.
3. Attach the signal cables to the connectors.
4. Attach the power cords to the outlets.
5. Turn on the devices.
• Sharp edges, corners and joints may be present in and around the system. Use care when handling
equipment to avoid cuts, scrapes and pinching. (D005)
DANGER: Heavy equipment — personal injury or equipment damage might result if mishandled.
(D006)
xii IBM Cloud Object Storage System: Slicestor 2212 Appliance Manual 3409-S00/3401-S00/3403-S00

DANGER: Professional movers are to be used for all relocation activities. Serious injury or death
may occur if systems are handled and moved incorrectly. (D008)
DANGER: Serious injury or death can occur if loaded lift tool falls over or if a heavy load falls off
the lift tool. Always completely lower the lift tool load plate and properly secure the load on the lift
tool before moving or using the lift tool to lift or move an object. (D010)
CAUTION:
T
The battery contains lithium. To avoid possible explosion, do not burn or charge the
battery.
Do not: hrow or immerse into water, heat to more than 100ºC (212ºF), repair or disassemble. (C003)
DANGER: Observe the following precautions when working on or around your IT rack system:
• Heavy equipment—personal injury or equipment damage might result if mishandled.
• Always lower the leveling pads on the rack cabinet.
• Always install stabilizer brackets on the rack cabinet.
• To avoid hazardous conditions due to uneven mechanical loading, always install the heaviest
devices in the bottom of the rack cabinet. Always install servers and optional devices starting
from the bottom of the rack cabinet.
• Rack-mounted devices are not to be used as shelves or work spaces. Do not place objects on top
of rack-mounted devices.
• Each rack cabinet might have more than one power cord. Be sure to disconnect all power cords in
the rack cabinet when directed to disconnect power during servicing.
• Connect all devices installed in a rack cabinet to power devices installed in the same rack cabinet.
Do not plug a power cord from a device installed in one rack cabinet into a power device
installed in a different rack cabinet.
• An electrical outlet that is not correctly wired could place hazardous voltage on the metal parts of
the system or the devices that attach to the system. It is the responsibility of the customer to
ensure that the outlet is correctly wired and grounded to prevent an electrical shock.
(R001 part 1 of 2)
Use the following general safety information for all rack mounted devices:
Safety and environmental notices xiii

Environmental notices
This information contains all of the environmental notices for IBM Systems products in English and other
languages.
CAUTION:
• Do not install a unit in a rack where the internal rack ambient temperatures will exceed the
manufacturer’s recommended ambient temperature for all your rack-mounted devices.
• Do not install a unit in a rack where the air flow is compromised. Ensure that air flow is not
blocked or reduced on any side, front or back of a unit used for air flow through the unit.
• Consideration should be given to the connection of the equipment to the supply circuit so that
overloading of the circuits does not compromise the supply wiring or overcurrent protection. To
provide the correct power connection to a rack, refer to the rating labels located on the equipment
in the rack to determine the total power requirement of the supply circuit.
• (For sliding drawers): Do not pull out or install any drawer or feature if the rack stabilizer
brackets are not attached to the rack. Do not pull out more than one drawer at a time. The rack
might become unstable if you pull out more than one drawer at a time.
• (For fixed drawers): This drawer is a fixed drawer and must not be moved for servicing unless
specified by the manufacturer. Attempting to move the drawer partially or completely out of the
rack might cause the rack to become unstable or cause the drawer to fall out of the rack.
(R001 part 2 of 2)
DANGER: Multiple power cords. The product might be equipped with multiple power cords. To
remove all hazardous voltages, disconnect all power cords. (L003)
xiv IBM Cloud Object Storage System: Slicestor 2212 Appliance Manual 3409-S00/3401-S00/3403-S00

The IBM Systems Environmental Notices information includes statements on limitations, product
information, product recycling and disposal, battery information, flat panel display, refrigeration and
water-cooling systems, external power supplies, and safety data sheets.
Declared noise emissions
Table 1. Declared noise emissions in accordance with ISO 9296(1,2,3)
Product description
Declared A-Weighted
Sound Power Level,
LWAd (B)
Declared A-Weighted
Sound Pressure Level,
LpAm (dB)
Operating Idling Operating Idling
Model S00
@ 25 deg. C room ambient
5.6 5.4 39 37
Model S00
@ 35 deg. C room ambient
7.7(4) 7.7(4) 61 61
Model S00
@ 25 deg. C room ambient
Acoustical Doors Feature codes
FC EC07 = back FC EC08 = front
5.2 5.0 34 32
Model S00
@ 35 deg. C room ambient
Acoustical Doors Feature codes
FC EC07 = back FC EC08 = front
7.0 7.0 55 55
Notes:
1. Declared level LWAd is the upper-limit A-weighted sound power level; Declared level LpAm is the mean
A-weighted sound pressure level measured at the 1-meter bystander positions.
2. All measurements made in conformance with ISO 7779 and declared in conformance with ISO 9296.
3. B, dB, abbreviations for bels and decibels, respectively. 1 B = 10 dB.
4.
Note: Government regulations (such as those prescribed by OSHA or European Community Directives) may
govern noise level exposure in the workplace and may apply to you and your server installation. This IBM
system is available with an optional acoustical door feature that can help reduce the noise emitted from this
system. The actual sound pressure levels in your installation depend upon a variety of factors, including the
number of racks in the installation; the size, materials, and configuration of the room where you designate the
racks to be installed; the noise levels from other equipment; the room ambient temperature, and employees'
location in relation to the equipment. Further, compliance with such government regulations also depends upon
a variety of additional factors, including the duration of employees' exposure and whether employees wear
hearing protection. IBM recommends that you consult with qualified experts in this field to determine whether
you are in compliance with the applicable regulations.
Safety and environmental notices xv

xvi IBM Cloud Object Storage System: Slicestor 2212 Appliance Manual 3409-S00/3401-S00/3403-S00

Support information
For more information on the product or help with troubleshooting, contact IBM Support at
[email protected] or visit the Directory of worldwide contacts.
© Copyright IBM Corp. 2016, . xvii

xviii IBM Cloud Object Storage System: Slicestor 2212 Appliance Manual 3409-S00/3401-S00/3403-S00

Chapter 1. Slicestor®2212 ApplianceManual
This manual contains the instructions for installing and maintaining the Slicestor®2212A appliance.
© Copyright IBM Corp. 2016, . 1

2IBM Cloud Object Storage System: Slicestor 2212 Appliance Manual 3409-S00/3401-S00/3403-S00