IBM Deskstar 22GXP User manual

IBM storage products
Installation guide
Deskstar 22GXP & 25GP
AT/IDE
DJNA-352500, DJNA-352030, DJNA-351520,DJNA-351010
DJNA-350510,DJNA-372200, DJNA-371800, DJNA-371350
DJNA-370910,DJNA-370450
Models:

Table of contents
Page 31
Glossary
.............................................................
....
Page 26
Warranty
.................................................................
Page 23
Appendix
................................................................
Page 21
Step 8: Operating system installation
..........................................
Page 21
Formatting
...............................................................
Page 18
FDISK
...................................................................
Page 18
Boot computer
............................................................
Page 16
Bios settings
.............................................................
Page 16
Step 7b: Custom install
.....................................................
Page 13
Ontrack Disk Manager
......................................................
Page 13
Step 7a: Easy install
........................................................
Page 13
Step 7: Installation and configuration
.........................................
Page 12
Step 6: Complete physical installation
.........................................
Page 12
Step 5: Connectors
........................................................
Page 11
Step 4: Mounting
..........................................................
Page 9
Step 3: Jumper settings
......................................................
Page 8
Step 2: Prepare for installation
................................................
Page 8
Step 1: Installation checklist
..................................................
Page 6
Hard disk drive installation flow chart
..........................................
Page 5
Hard disk drive handling guide
................................................
Page 4
Hardware description
........................................................
Page 3
Introduction
..........................................................
.....
IBM storage products
Page 2
IBM Hard Disk Drive Technical Support Center version 1.0

Introduction
This manual was prepared to help you install your IBM Deskstar 22GXP or 25GP hard drive in most
computer systems. If you do not feel comfortable installing this drive yourself, contact a qualified installer
to assist you.
International Business Machines Corporation provides this publication "AS IS" without warranty of any
kind, either expressed or implied, including, but not limited to, the implied warranties of merchantability or
fitness for a particular purpose. Some states do not allow disclaimers of express or implied warranties in
certain transactions. Therefore, this statement may not apply to you.
This publication could include technical inaccuracies or typographical errors. Product data and
specifications are subject to change without notice. Changes are periodically made to the information
herein; these changes will be incorporated in new editions of the publication. IBM may make
improvements or changes in the products or the programdescribed in this publication at any time.
This publication may contain reference to or information about IBM products (machines and programs),
programming, or services that are not available in your country. Such references or information must not
be construed to mean that IBM intends to make available such IBM products, programming, or services
in your country.
Product description data contained herein represents IBM’s design objectives and is provided for
comparison among IBM products; actual results may vary based on a variety of factors. Except as
explicitly stated in the Warranty section of this Guide, the product data contained herein does not
constitute a warranty. Questions regarding IBM warranty terms or the methodology used to derive data
should be referred to an IBM representative.
Technical information about IBM hard disk drive products can be obtained via the Internet at:
http://www.ibm.com/harddrive
or by calling the IBM Hard Disk Drive Technical Support Center at 888.426.5214.
©Copyright International Business Machines Corporation 1999. All rights reserved. Note to US
Government Users - Documentation related to restricted rights - Use, duplication or disclosure is subject
to restrictions set forth in GSA ADP Schedule Contract with IBM Corp.
IBM is a registered trademark of the International Business Machines Corporation. The following are also
trademarks or registered trademarks of the International Business Machines Corporations in the United
States, other countries, or both: Deskstar, OS/2, and Surepath. Any other products or trademarks are
the property of their respective owners.
IBM storage products
Page 3
IBM Hard Disk Drive Technical Support Center version 1.0

Hardware description
The Deskstar 22GXP and 25GP are available in various models with the following options:
5,400
DJNA-350510
5.1GB
5,400
DJNA-351010
10.1GB
5,400
DJNA-351520
15.2GB
5,400
DJNA-352030
20.3GB
5,400
DJNA-352500
25GB
7,200
DJNA-370450
4.5GB
7,200
DJNA-370910
9.1GB
7,200
DJNA-371350
13.5GB
7,200
DJNA-371800
18GB
7,200
DJNA-372200
22GB
RPM
Model
Capacity
The Deskstar 22GXP and 25GP family has an advanced Ultra ATA interface that supports transfer rates
of up to 66.6 MB/sec. To take advantage of the higher transfer rate, your computer will need to have a
controller that supports the Ultra ATA/66 interface and a 40-pin, 80 conductor cable. If you have an older
interface such as Multi-word DMA Mode-2, PIO Mode-4, or Ultra ATA/33 the drive will still function, but
will be limited to data transfer speeds significantly lower than 66.6MB/sec due to the lower speed of your
controller. If you have a slower controller, you may wish to purchase an Ultra ATA/66 controller card to
take advantage of Deskstar’s 66.6MB/sec data transfer rate. An Ultra ATA/66 controller card will fit into
any available slot in your computer. At this printing, Promise Technology is the only company offering an
Ultra ATA/66 controller card. For more information, see their Web site at:
http://www.promise.com
The Deskstar 22GXP and 25GP are designed for desktop applications that demand advanced data
storage solutions, such as audio/video editing, computer-aided design and manufacturing (CAD/CAM),
3D graphics, animation and photo manipulation, Web page design, or data mining and warehousing.
They are ideal for use in entry servers, entry workstations, and desktop personal computers.
The Deskstar 22GXP and Deskstar 25GP families are designed to work with MMX systems.
Compatibility listings are included in the Appendix. Before you begin installation, please read the “Hard
disk drive handling guide” on the following page.
IBM storage products
Page 4
IBM Hard Disk Drive Technical Support Center version 1.0

Hard disk drive handling guide
These notes are designed to provide a simple overview of the need for cautionwhen handling a disk
drive.
Disk drives can be easily damaged by electrical static shock or rough handling. In order to minimize the
risk of damage to a disk drive, it is essential that the drive be handled while resting on a cushioned,
electrostatically safe surface. Examples of static-safe mats available at the time of this printing are 3M's
8210 table mat and 3M's "First Touch" computer pad.
Great care should be taken when handling disk drives. Do not bump them against any object. When
attaching brackets or mounting the drive in the computer, be very careful. It is very easy to
unintentionally introduce shocks which exceed specifications.
Please note that the capacity of each disk drive to withstand electrical or mechanical shock varies
according to its design. The IBM Hard Disk Drive Technical Support Center can advise you on the
suitability of your Deskstar drive for a specific application.
Damage incurred to a drive might not be immediately evident and could cause the drive to fail months
later.
IBM storage products
Page 5
IBM Hard Disk Drive Technical Support Center version 1.0

Hard disk drive installation flow chart
IBM storage products
Page 6
IBM Hard Disk Drive Technical Support Center version 1.0
Step 1
Installation checklist
Page 8
Step 2
Prepare for installation
Page 8
Step 3
Jumper
settings
Page 9
Step 5
Connectors
Page 12
Connect cable to add-on
Ultra ATA/66 controller
Page 12
Connect cable
to onboard IDE
ports
Page 12
Secondary
port
Page 12
Primary
port
Page 12
Step 4
Mounting the drive
Page 11
Step 6
Complete
physical
installation
Page 12
Step 7
Installation and
configuration
Page 13
Step 7a
Easy Install
Page 13
Step 7b
Custom Install
Page 16
Ontrack® Disk Manager
Page 13 BIOS settings
Page 16
Boot computer
Page 18
FDISK
Page 18
Formatting
Page 21
Step 8
Install operating system if required
Page 21

Step 1: Installation checklist
To install the Deskstar drive you may need the following items depending on your computer:
ŸThe installation kit (as shown in the diagram below) containing the Deskstar drive,4 mounting
screws, IDE cable, Ontrack® Disk Manager, and any related publications. Save the box the drive
came in.
ŸThe documentation that came with your computer or storage enclosure.
ŸA small, flat-blade screwdriver.
ŸAn IDE controller, which is either built in or an adapter inside your computer, and any related
documentation.
ŸMounting brackets, if required for your computer. Contact your place of purchase if you are not
certain if mounting brackets are required.
ŸA bootable DOS diskette. (See the section entitled Making a Bootable Diskette in the Appendix.)
ŸIf you are replacing an older internal drive with the new Deskstar drive and want to copy all of the
files from the older drive to your new one, you may need additional software. (See the section
entitled Drive Copy in the Appendix.)
IBM storage products
Page 7
IBM Hard Disk Drive Technical Support Center version 1.0
Installation
Guide
Ontrack
Jumpers
Screws
Screwdriver
Disk Manager
IDE Cable
Installation Guide
Hard Disk Drive

Step 2: Prepare for installation
Begin by backing up your existing drive to avoid any loss of data during installation. (See the section
entitled Backup and Restore in the Appendix.) After completing the backup, shut down as normal.
Opening your computer
ŸTurn the system off.
ŸUnplug the power cord from the wall outlet.
ŸRemove all cables from the back of your computer, labeling them if necessary.
ŸRemove the cover from your computer. (Consult your user's guide for instructions if needed.)
Unpackaging your hard drive
ŸIf available, use an ESD (Electronic Static Discharge) wrist strap while handling your drive.
ŸIf an ESD wrist strap is not available, discharge static electricity by establishing a common voltage
between your body and the hard drive. Simultaneously touch the hard drive in its anti-static bag and
an unpainted metal surface on the outside of your computer system with your bare hands.
ŸRemove the drive from the anti-static package that it was shipped in. Handle the drive only by the
sides and avoid excessive movement until the drive has been mounted.
ŸDo not touch the main computer chip board.
ŸDo not drop the drive. A drop from only 1/4 inch could permanently damage your hard drive.
ŸPlace the drive carefully on a static free area.
ŸRecord the following information:
Drive Model ________________ Date of Purchase_________________
Drive P/N __________________ Place of Purchase_________________
Serial # ____________________
ŸIf you currently have a hard drive in your system you may want to record the CMOS settings. This
information is in your BIOS setup. You can enter your BIOS setup by pressing the key sequence for
your system while booting. (See Custom Install on page 16.)
Cylinders _______________________ Sectors/Track_____________________
Heads __________________________ Landing Zone _____________________
Write Pre Comp (if you have this category) __________________
Note:Do not low-level format your drive! IBM drives are low-level formatted by the manufacturer and
reformatting may cause permanent damage to your drive and your system. (See the section entitled
Utilities in the Appendix.)
IBM storage products
Page 8
IBM Hard Disk Drive Technical Support Center version 1.0

Step 3: Jumper settings
The jumper settings are found on the hard drive next to the interface connector, as shown below.
Jumper settings are physical settings that must be changedfor different uses of ahard drive. If your
drive will be used as a single drive or as a boot drive, no changes are required. The drive is shipped with
jumpers set for Master.
Master
This setting should be used if you are removing your current drive from the system and replacing it with
the Deskstar drive. Place a jumper on pins A-B and G-H to make this drive the Master.
Slave
Use this setting if you want to retain your old drive as the boot drive and have the new drive available for
program and data storage. Place a jumper on pins A-B and C-D to make this drive the Slave.
Cable Select
This setting should be used if your system requires special “cable select” cables. Place a jumper on pins
A-B and E-F for Cable Select.
Slave Present
This setting should be used if your BIOS setup does not detect the slave drive. Place a jumper on pins
E-F and G-H.
IBM storage products
Page 9
IBM Hard Disk Drive Technical Support Center version 1.0

Some BIOSs have a limitation when translating the cylinder, head, and sector information which prevents
them from correctly detecting the capacity of larger drives. If your BIOS is reporting the Deskstar’s
capacity incorrectly, use the 15 logical head settings rather than the 16 logical heads, shown below.
Jumper settings
IBM storage products
Page 10
IBM Hard Disk Drive Technical Support Center version 1.0

Step 4: Mounting
After setting the jumpers, mount the hard drive in your system. Thedrive can be mounted with any of its
six surfaces facing down. See below for mounting hole locations.
Mounting hole locations
You must ensure that the drive has sufficient air flow. Mount the drive in the system using four 6-32 UNC
screws. The maximum screw length is 4.0 mm for the side holes and 4.5 mm for the bottom holes.
Mount the drive securely enough to prevent it from excessive motion or vibration.
If you are mounting your drive in a 5 inch bay, you may need to purchase mounting brackets from your
computer manufacturer for the drive to be mounted securely.
IBM storage products
Page 11
IBM Hard Disk Drive Technical Support Center version 1.0

Step 5: Connectors
After the drive has been carefully mounted, connect the IDE cable (included) and the power cable to the
drive. If you are using a cable already installed in your computer, ensure that the cable length does not
exceed 18 inches (45.7 cm). (Note that the IDE connector and power connector are keyed for proper
insertion.)
Connector locations
Step 6: Complete physical installation
Plug the cable into the onboard port. If you have added an Ultra ATA/66 controller card plug the cable
into the controller. The figure below shows the possible location of the onboard ports. Each port is
marked on the motherboard.
IBM storage products
Page 12
IBM Hard Disk Drive Technical Support Center version 1.0
Interface Connector Power Connector
Jumper Block

To take advantage of the Ultra ATA/66 transfer rate available with the Deskstar 22GXP and 25GP, an
add-on Ultra ATA/66 controller must be used. This card can be plugged into one of the expansion slots.
The Deskstar drive would then be connected to the Ultra ATA/66 card rather than the primary or
secondary slot on the motherboard.
If you are not using an Ultra ATA/66 card, plug the IDE cable into one of the two available slots on the
motherboard. The first two devices should be connected to the “primary” slot and the second two
devices should be connected to the “secondary” slot. These devices may be hard drives, CD-ROMS,or
removable drives.
Complete the physical installation by replacing the cover on the computer, connecting all cables, and
plugging the power cord into the wall.
Step 7: Installation and configuration
Step 7a: Easy install
When you purchased this drive from IBM, you received a copy of Ontrack® Disk Manager. This software
is necessary if your BIOS does not support drives over 8.4 GB. This easy installation will use the Disk
Manager diskette to partition and format your drive. If the easy installation does not work, or you choose
not to use Disk Manager, continue to the section entitled Custom Installation.
Ontrack ® Disk Manager
Turn on your computer after you have inserted the Ontrack® Disk Manager diskette. Note: The following
screen shots are examples and may not appear in the same format on your system.
A large blue IBM screen will appear after several seconds, followed by the screen below. Select Easy
Disk Installation.
The screen on the following page will appear.
IBM storage products
Page 13
IBM Hard Disk Drive Technical Support Center version 1.0
IBM
Disk Manager Version 9.42.02
Select an Installation Option
(E)asy Disk Installation
(A)dvanced Disk Installation
(M)aintenance Menu
(U)pgrade Disk Manager
(V)iew/Pring Online Manual
Exit Disk Manager

If the drive list is correct, select (Y)es. The screen shown below will follow.
Select the operating system you plan to install (or the operating system installed on an existing drive). If
you are using Windows® 95 version B or Windows® 98, Disk Manager will create a FAT 32 file system
which will allow you to create 1 partition using all existing space on your hard drive. If you do not wish to
use the FAT 32 file system, you can select the FAT 16 file system by choosing (N)o from the following
screen.
IBM storage products
Page 14
IBM Hard Disk Drive Technical Support Center version 1.0
IBM
Disk Manager Version 9.42.02
Select an Installation Option
(E)asy Disk Installation
(A)dvanced Disk Installation
(M)aintenance Menu
(U)pgrade Disk Manager
(V)iew/Pring Online Manual
Exit Disk Manager
Drive List
1) IBM-DTTA-351680
Disk Manager found 1 drive.
Is the drive list correct?
(Y)ES
(N)O
IBM
Disk Manager Version 9.42.02
Select an Installation Option
(E)asy Disk Installation
(A)dvanced Disk Installation
(M)aintenance Menu
(U)pgrade Disk Manager
(V)iew/Pring Online Manual
Exit Disk Manager
Select the operating system you
are using or plan to install.
Windows 95 (or OSR1)
Windows 98 (or Windows 95 OSR2)
Windows NT 3.51 (or earlier)
Windows NT 4.0 (or later) or OS2
DOS/Windows 3.1x
Other
Return to previous menu

Select (Y)es to continue. After Disk Manager has finished partitioning and formatting your drive, the next
screen will appear.
Your drive has now been partitioned and formatted. If there isn’t already an operating system on an
existing drive, load an operating system.(See the section entitled Operating Systems on page 21.)
IBM storage products
Page 15
IBM Hard Disk Drive Technical Support Center version 1.0
IBM
Disk Manager Version 9.42.02
(E)asy Disk Installation
(A)dvanced Disk Installation
(M)aintenance Menu
(U
(V
EDisk 1 has been successfully installed!
The DOS partitions that have been created are now formatted.
Each partition will be accessible as a logical drive letter after rebooting
(Any key to continue)
Disk Manager Status
IBM
Disk Manager Version 9.42.02
Select an Installation Option
(E)asy Disk Installation
(A)dvanced Disk Installation
(M)aintenance Menu
(U)pgrade Disk Manager
(V)iew/Pring Online Manual
Exit Disk Manager
Disk Manager can format your hard drive using the 32-Bit FAT file system.
Would you like to install thi sdrive using FAT32?
(Y)ES
(N)O

Step 7b: Custom install
If you do not wish to use Ontrack® Disk Manager, or if your system will install the drive without the
overlay program, continue by checking your drive’s settings in your BIOS.
BIOS settings
Begin by checking the CMOS settings. The example below is an Award© BIOS version 4.51. Other
BIOSs should be similar. Follow the instructions provided with your system. To enter the CMOS setup
screen press the key sequence designated by your system manufacturer (i.e. <F1>; <DELETE> <ESC>;
<CTRL> <ALT> <S>) during the initial boot process. Select “Standard CMOS Setup”. This selection will
bring up the following screen.
IBM storage products
Page 16
IBM Hard Disk Drive Technical Support Center version 1.0
INTEGRATED PERIPHERALS
SUPERVISOR PASSWORD
USER PASSWORD
IDE HDD AUTO DETECTION
HDD LOW LEVEL FORMAT
SAVE & EXIT SETUP
EXIT WITHOUT SAVING
: Select Item (Shift)F2: Change Color
F10 Save & Exit Setup
Time, Date, Hard Disk Type...
STANDARD CMOS SETUP
BIOS FEATURES SETUP
CHIPSET FEATURES SETUP
POWER MANAGEMENT SETUP
PNP/PCI CONFIGURATION
LOAD BIOS DEFAULTS
LOAD SETUP DEFAULTS
ROM PC/ISA BIOS (2A5IHROB)
STANDARD CMOS SETUP
AWARD SOFTWARE, INC.

The above example shows an 8455MB drive connected to the primary port on the motherboard and set
as a Master drive. The drive used in this example has a capacity of 16.8 GB. This BIOS will not
recognize capacities over 8.4 GB. Ontrack® Disk Manager will be needed to overcome the limitation.
(Go back to the section entitled Easy Installation.)
If the previous screen shows a drive other than the Deskstar 22GXP or 25GP or shows nothing at all, you
will need to go into the “IDE HDD Auto Detection”. You can get there from the main menu of the BIOS
setup.
IBM storage products
Page 17
IBM Hard Disk Drive Technical Support Center version 1.0
Date (mm:dd:yy) : Tue, May 27 1998
Time (hh:mm:ss) : 18:12:49
HARD DISKS TYPE SIZE CYLS HEAD PRECOMP LANDZ SECTOR MODE
Primary Master : User 8455 16383 16 65535 16382 63
AUTO
Primary Slave : None 0 0 0 0 0 0 -------
Secondary Mst : None 0 0 0 0 0 0 -------
Secondary Slv : None 0 0 0 0 0 0 -------
Drive A : 1.44M, 3.5 in.
Drive B : None
Video : EGA/VGA
Halt On: All Errors
Base Memory: 640K
Extended Memory: 64512K
Other Memory: 384K
Total Memory: 65536K
: Select Item PU/PD/+/- : Modify
F1 : Help (Shift) F2 : Change Color
ROM PC/ISA BIOS (2A59IR09)
STANDARD CMOS SETUP
AWARD SOFTWARE, INC.
HARD DISKS TYPE SIZE CYLS HEAD PRECOMP LANDS SECTOR MODE
Primary Master :
Select Primary Slave Option (N = Skip) : N
OPTIONS SIZE CYLS HEAD PRECOMP LANDZ SECTOR MODE
2(Y) 8447 1027 255 0 16382 63 LBA
1 8455 16382 16 65535 16382 63 Normal
3 8455 8191 63 65535 16382 63 Large
Note: Some OSes (like SCO-UNIX) must use "NORMAL" for installation
ESC : Skip
IDE HDD Auto Detection
ROM PC/ISA BIOS (2A5IHROB)
STANDARD CMOS SETUP
AWARD SOFTWARE, INC.

Make a selection and return to the main menu. Click on “Standard CMOS Setup”. You will see that the
BIOS recognizes only 8455 MB and will need to use Ontrack® Disk Manager for the entire 16 GB to be
recognized. (Go back to the section entitled Easy Installation.)
If you can answer “yes” to any of the following, proceed with FDISK.
ŸYou have purchased a smaller capacity drive (under 8.4 GB) and the BIOS recognizes
the correct capacity.
ŸYour BIOS recognizes the full capacity of the drive.
ŸYou have connected your drive to an Ultra ATA/66 card.
Press [ESC] to continue and then select Save and Exit.
Boot computer
Turn on your computer after you have inserted a bootable diskette such as DOS or your Windows®
startup diskette. You will need to use Windows® 95 OS/R2 or Windows® 98 FDISK for drives larger
than 8 GB. DOS FDISK will not recognize drives larger than 8 GB.
FDISK
Type FDISK at the A:\ prompt after booting to a bootable diskette. If Windows® 95 OS/R2 or Windows®
98 is used, the following screen will appear.
Type Yto select the FAT 32 file system. Type Nto select the FAT 16 file system.
IBM storage products
Page 18
IBM Hard Disk Drive Technical Support Center version 1.0
Your computer has a disk larger than 512 MB. This version of Windows
includes imporved support for large disks, resulting in more efficient use of
disk space on large drives, and allowing disks over 2 GB to be formatted as
a single drive.
IMPORTANT: If you enable large disk support and create any new drives on
this disk, you will not be able to access the new drive(s) using other
operating systems, including some versions of Windows 95 and Windows
NT, as well as earlier versions of Windows and MS-DOS. In addition, disk
utilities that were not designed explicitly for the FAT32 file system will not be
able to work with this disk. If you need to access this disk with other
operating systems or older disk utilities, do not enable large drive support.
Do you wish to enable large disk support (Y/N)...............? [N]

The following screen allows you to create partitions. You will have five options if you have more than one
drive. Option 5 allows you to select the drive you wish to partition.
Select option 1 to Create DOS partition.
Select option 1 to Create Primary DOS Partition. If this is to be the boot drive, set this partition to
“Active”.
Press [ESC] to return to the FDISK options. Create an Extended DOS Partition by selecting option 1
from the main menu and option 2 from the second menu. (Both menus shown above.)
IBM storage products
Page 19
IBM Hard Disk Drive Technical Support Center version 1.0
PC DOS Version 7.0
Fixed Disk Setup Program
Copyright IBM Corporation 1983-1994
FDISK Options
Current fixed disk drive: 1
Choose one of the following:
1. Create DOS partition or Logical DOS Drive
2. Set active partition
3. Delete partition or Logical DOS Drive
4. Display partition information
5. Change current fixed disk drive
Enter choice:[1]
Press ESC to exit FDISK
Create DOS Partition or Logical DOS Drive
Choose one of the following:
1. Create Primary DOS Partition
2. Create Extended DOS Partition
3. Create Logical DOS Drive(s) in the Extended DOS partition.
Enter choice: [3]
Press ESC to return to FDISK Options

The previous example is based on the Deskstar 16GP model DTTA-350320 which is a 3.2 GB drive.
Note that the Maximum Capacity shows only 3099 MB instead of 3240 MB. This is because some
system BIOSs recognize a Megabyte as 1,048,576 bytes (binary). Drive manufacturers recognize a
Megabyte as 1,000,000 bytes (decimal). The capacities are the same in actual number of bytes.
After creating the Extended DOS Partition, press [ESC] to return to the FDISK main menu. Select option
1 to create a Logical DOS Drive, then option 3 to create a Logical DOS Drive in an Extended Partition.
Press [ESC] to return to FDISK and [ESC] again to restart the system. The system must be restarted for
the partitions to be recognized.
IBM storage products
Page 20
IBM Hard Disk Drive Technical Support Center version 1.0
PC DOS Version 7.0
Fixed Disk Setup Program
Copyright IBM Corporation 1983-1994
Create Extended DOS Partition
Current fixed disk drive: 2
Partition Status Type Volume Label Mbytes System
Usage
D:1 A PRI DOS 2047 UNKOWN 66%
Total disk space is 3095 Mbytes (1 Mbyte = 1048576 bytes)
Maximum space available for partition is 1047 Mbytes (34%)
Enter partition size in mbytes or percent of disk space (%) to create an
Extended DOS Partition.........[1047]
Press ESC to return to FDISK options
Create Logical DOS Drive(s) in the Extended
DOS Partition
No logical drives defined
Total Extended DOS Partition size is 1047 Mbytes
(1 MByte = 1048576 bytes)
Maximum space available for logical drive is 1047Mbytes (100%)
Enter logical drive size in Mbytes or percent of disk space (%).....[1047]
Press ESC to return to FDISK Options